Reason to be proud of your garage Adam. A great space, facility, workshop. The envy of many, and all your own work too. A great achievement. Well done. 👏
Your garage is a thing of envy. I'm sure there are many others who watch and wish. It's coming on great. Only thing I'd mention is about the heater venting at top, heat rises, what it not be better at the bottom?
When you mentioned insulating to stop your neighbours having to hear you. I laughed as some of them might see you go in there on your own and then hear you talking to yourself. Anyway keep up the great videos and I am well jealous of your garage.
Coming from a cold country it always amazes me how cold, humid and uninsulated many garages and workshops are in the uk :) it wasn't very thick insulation but roof insulation is really effective. Next step would be a small heat pump, so nice to have in the garage :)
make a wood frame around the roller shutter, + make 2 lift out insulation "doors", makes a hell of a difference, especially with grinder noise,. use some old roof grab-handles on them, 10 seconds to lift them out, best thing i ever done [says the neighbour]
Had to use that foil tape outside for preparing the foundations for houses. Same idea as what your doing but the insulation goes down then concrete is poured on top. What a nightmare of a job in the winter 😝
I've just done mine between the joists. Was a right pain, had to go between though as I have a flat roof. Next I'm using tongue and groove uPVC to cover it over and make it light and bright
Hi Adam, I was pleased at 3.20 to hear you say you were going to pull the car out first! (I was getting a bit nervous as getting an Adam sized dent out of the cossie’s roof wouldn’t be too easy ha ha!) 😂
Nice work mate 👍 another good tip from a thermal insulator (hvac and pipes) always hang the tape from a lose belt around your waist for easy access, and never rip the backing off.
Shame you only built it single skin with no cavity but I know it was done for maximum width inside. I built 1 3 years ago, fully insulated roof, insulated door, insulated cavity and breeze blocks and it still condensed up in winter. I think I should have insulated the floor under the concrete as I think the cold rises up out of the ground. I’ve had to put a small heater and a dehumidifier in over winter months.
Adam I think that looks absolutely brilliant and I guess and also will reflect a lot more light than just the dark felt and timber joists. Very nice job sir! 👍
Few bits, wear a mask with this stuff the dust is bad and gets on your chest. And rather than doing the tape in small sections, just peel a load back, stick it down and rip the tape but not the backing. makes it easier to peel and stops it curling up.
Great garage mod that is. Better working/storage conditions & better light. Thought about doing the same many times, this may be the inspiration I need to finally do it! 👌🏻
You have done a nice job that am a plasterer by trade so somehow we have adopted this job on sites horrible stuff a mask is a must. I would board and skim the frount part before the rafters change make it nice and bonny haha Whys they 2 sort of rafters
Want to do this in my garage but I use frame for storage,it’s always cold and condensation everywhere,even me dart board started to mold,too job fella 👍
They do what’s called a midget 2 post ramp. It’s a ramp but only lifts the car up about 3 foot but enough room to work under the car for use in garages that have limited roof space
From somebody who's done this in his own house loft I can completely agree Adam, also you've covered all the points that I found out (the hard way) doing this job myself so well done. Great video mate
I've just put a Meaco dehumidifier in mine as anything metal (+ other stuff) was getting really wet from lots of condensation, especially in the tail end of Autumn and Spring when there's bigger temperature fluctuations and as wer fella here says condensation. Defo helps.
Looks miles better...could have used cavity batts (1200mm x 450mm) usually same gaps between trusses etc then plasterboarded over to give an even better look/finish!
@@elobiretv perhaps there are different grades of cheap chinese diesel heaters?, my friend's "quality" item was nice + warm, but the garage walls + ceiling were soaking next night, when he didnt use the heater, it was fine
“Shaking like a shitting dog” I haven’t heard that expression for years lol 😂
Back on with the Saph on the next video fellas.
Can’t wait for it mate
Donuts ?
Absolutely love how from needing a sunroof frame this has turned into one of my favourite channels go on lad
Cheers fella 👍🏻
Good insight for someone looking too insulate a garage or shed. How much did the 20 sheets of insulation cost mate? Cheers looking good Adam.
Probably the best channel on here by far now like….keep up the fantastic job mate
This is great...lovely Cossy in the garage as well..Peace from Ireland Mate!
Reason to be proud of your garage Adam. A great space, facility, workshop. The envy of many, and all your own work too. A great achievement. Well done. 👏
Lovely job Adam. You've given me some inspiration for a video on insulating our drying room
Crazy to think how far you have come Adam. It was going on the hunt for a sun roof that started your epic channel. Keep up the great work mate 👍
Thanks Shane. Are you missing your Sierra?
Great video, and making me realise I need a trip to my sisters, Washington Tyne and Wear ❤
Your garage is a thing of envy. I'm sure there are many others who watch and wish. It's coming on great. Only thing I'd mention is about the heater venting at top, heat rises, what it not be better at the bottom?
Hi Adam
Cars looking spot on mate looking forward to the next video
Awesome inchulashion job Adam 😂
Nice one - looks mint that Adam - well done!
Great video and great job. When I get a garage, I’ll be doing this.
When you mentioned insulating to stop your neighbours having to hear you. I laughed as some of them might see you go in there on your own and then hear you talking to yourself. Anyway keep up the great videos and I am well jealous of your garage.
Well done mate looks a good job!
Brilliant mate . Great how you always have a crack at doing everything yourself to save money💷💰💰
Coming from a cold country it always amazes me how cold, humid and uninsulated many garages and workshops are in the uk :) it wasn't very thick insulation but roof insulation is really effective. Next step would be a small heat pump, so nice to have in the garage :)
This video is awesome. Thanks Adam, I will use this when i do my roof!
Top job mate looking good 👍
Looking good mate. Will definitely be watching these videos again when it comes to building my garage!
Good vid Adam my garage roof is a right pis tek for condensation might invest in some of this stuff !!!
Nice job matey 👍🏻
Resin flooring next for you,my mate has it in his garage with a design and lush sparkle 👌🏻
make a wood frame around the roller shutter, + make 2 lift out insulation "doors", makes a hell of a difference, especially with grinder noise,. use some old roof grab-handles on them, 10 seconds to lift them out, best thing i ever done [says the neighbour]
Had to use that foil tape outside for preparing the foundations for houses. Same idea as what your doing but the insulation goes down then concrete is poured on top. What a nightmare of a job in the winter 😝
Enjoying these garage updates Adam, all useful stuff to know mate 🍻
Brilliant job well done Adam looking brilliant 👍🏽👍🏽
You are clearly very talented. Great video mate well done 👍👏
Loving the hand tattoo 😅
Nice one Adam, good job well done I'd say! you know you want to do the walls now too though! Another video! Cheers mate
I've just done mine between the joists. Was a right pain, had to go between though as I have a flat roof. Next I'm using tongue and groove uPVC to cover it over and make it light and bright
Great job Adam!!! Thumbs up for sure!
Great video - I’ve got a single post lift for my trials car / caterham. Its dead handy. Love the ford - my dad had one as a company car in the 80”s
Hi Adam, I was pleased at 3.20 to hear you say you were going to pull the car out first! (I was getting a bit nervous as getting an Adam sized dent out of the cossie’s roof wouldn’t be too easy ha ha!) 😂
Adam , check you have a few ridge vent tiles to allow the air to flow .
He doesn't need any vents he's got Air Permeable Breather Membrane
Awesome job mate paint the floor will look mint
Nice work mate 👍 another good tip from a thermal insulator (hvac and pipes) always hang the tape from a lose belt around your waist for easy access, and never rip the backing off.
Shame you only built it single skin with no cavity but I know it was done for maximum width inside. I built 1 3 years ago, fully insulated roof, insulated door, insulated cavity and breeze blocks and it still condensed up in winter. I think I should have insulated the floor under the concrete as I think the cold rises up out of the ground. I’ve had to put a small heater and a dehumidifier in over winter months.
Nice job, well done
Adam I think that looks absolutely brilliant and I guess and also will reflect a lot more light than just the dark felt and timber joists. Very nice job sir! 👍
It should stay a lot cooler during the summer too! 👍
Savage job Adam 👍👍
The glitter gekko is a bit of you rocking it buddy 👍
rubber flooring next? that hard rubber with raised circles? will reduce the echo in the room and be much nicer to work in?!
Few bits, wear a mask with this stuff the dust is bad and gets on your chest. And rather than doing the tape in small sections, just peel a load back, stick it down and rip the tape but not the backing. makes it easier to peel and stops it curling up.
Also get a tape gun
"Shaking like a shitting dog"... omg I near on spat my beer out when I heard that!
Good work Adam, better environment for the cars and you now😊🥵
Exactly Alex 😊👍🏼
Mint mate wish I could do something like that it's my dream
Nicely done
Little tip for anyone doing this, put the roll of foil tape on a belt much easier and just pull it off the backing paper to any length you can manage
Good video Adam!
I would love to know what’s best for a steel cladded shed, it’s non drip cladding roof and 50mm box section. Thank you for the video Adam.
tape engineering at its finest
never mind that what's the green ghekko on your left hand about?
Where did you find the best deal for buying the boards please?
Canny job Adam, did my mancave recently and it makes a world of difference.
Looks mint mate 👏🏼
Great garage mod that is. Better working/storage conditions & better light. Thought about doing the same many times, this may be the inspiration I need to finally do it! 👌🏻
You have done a nice job that am a plasterer by trade so somehow we have adopted this job on sites horrible stuff a mask is a must. I would board and skim the frount part before the rafters change make it nice and bonny haha
Whys they 2 sort of rafters
Great vid, well done
Hiya , you asked me to telegram?
What’s your email? Andy
Excellent video and something I want to do in mine 🙂
Always good content
Does any condensation form on the foil you can see? I want to do this in mine
Mate that’s awesome. I’m literally just looking into similar myself. Im only local - would be mint to take a look sometime!
Want to do this in my garage but I use frame for storage,it’s always cold and condensation everywhere,even me dart board started to mold,too job fella 👍
Stunning Adam
Thanks Dave
Belting job Adam. Await experts opinion in the comments section
About time mate... thought you were MIA!
Belter of a job mate 👍
Looks bang on that buddy and hopefully it sorted the condensation and stops your neighbours hearing you wibble on to the camera lol
They do what’s called a midget 2 post ramp. It’s a ramp but only lifts the car up about 3 foot but enough room to work under the car for use in garages that have limited roof space
Thanks, that was very helpful.
I see you have the big air-gap above the pir board but do you have ventilation to the air-gap?
From somebody who's done this in his own house loft I can completely agree Adam, also you've covered all the points that I found out (the hard way) doing this job myself so well done. Great video mate
Scam ….. that isn’t Adam
@@Bod3009 reported!
You'll be getting a sofa and a big telly on the wall next. Proper man cave😀👍
Make sure you have vented soffit or put some vents into keep the air flow circulating above the insulation that type needs airflow above it
Look at the guns on him man !😊 go on Adam !
Make sure if you are fitting a two post lift that your concrete was mixed to the correct spec or you will get the bolts breaking out.
Been wanting to do this in my two 12x8 joint sheds, walls and roof. any tips any one, I keep my restored 2 strokes in there
Great job Adam I'd love 2 do that 2 my garage bit DIY is not my forte 😀
You can do it Alan, it's not that hard
@@Adam151082 I've only got 2 look at a blade & I bleed mate
No fireboard then?
Will you be filming the next vid in your Speedos? Parental Guidance required.
Great job Sir
brilliant job might do mine is the boards expensive
Adam do you only really need a vapour barrier when you’re gna live in it?
I've got a question, where do you find the time for all the car restoration let alone adding insulation jobs into the mix 😀
@AdamSmithGiveaway. oh whal, really??? Do you want me to send you my bank details now??
Quality video
Did the insulation sort the condensation mate?
How much Adam to complete the project
Let's try that again
How much to complete the project Adam
nice tattoo 😊
True. I noticed when the temp changes my car is soaking wet underneath with condensation. Not good. Factor this thousands of times over a cars life!!
I've just put a Meaco dehumidifier in mine as anything metal (+ other stuff) was getting really wet from lots of condensation, especially in the tail end of Autumn and Spring when there's bigger temperature fluctuations and as wer fella here says condensation.
Defo helps.
A Cosworth, 147mph before cameras up the M11 to Stanstead.
Scared myself 😂😂
Where did you buy the boards from and the cost mate
How far are then rafters looks to much to me min of 800 by regsmight be camera
Your meant to tape the end of the rough edges of the boards. You might a thermal gap. Some spray foam in it.
Looks miles better...could have used cavity batts (1200mm x 450mm) usually same gaps between trusses etc then plasterboarded over to give an even better look/finish!
fantastic mate. well done. what camera do you have? Great pic and sound!
Adam get yourself a little 5kw Chinese diesel heater. About £150. We’ll worth the money,simple to install. Plus it’s another video for you to make😉
1 gall of diesel burnt will make about 2 gallon of water, so dinnit
Cheap Chinese heater an x2 valuable cars don’t mix well
Fire extinguishers 🧯 at the ready
@@weirdobagins8948 the heaters can be installed outside in a box so there is no risk at all from warm air. 😳
@@paulriggers1558 And all that water will go outside in the exhaust? It will actually dry the air because it's replacing the damp air.
@@elobiretv perhaps there are different grades of cheap chinese diesel heaters?, my friend's "quality" item was nice + warm, but the garage walls + ceiling were soaking next night, when he didnt use the heater, it was fine
This guy is a proppa dude!
Is that it or any more cosmetic work to get done up there?
How wide is your garage mate
top tip building a garage have cavity walls. its ok insulating the roof but all the heat is lost through the brick wall