Some people would say having commercial-grade safety systems installed in a residential structure is redundant and unnecessary. Way i see it as thats probably the most fire safe house in your county, and its your house, you do what you want with it. I would love to do something like this myself to my house honestly. Problem is i dont own one yet 😂. At the bare minimum if that equipment never really helps you in an incident [though I know at least the power backup and emergency lighting systems have], the experience and knowledge gained from doing all that work - very clean and professionally done by the way - is more valuable than all of the equipment monetary costs combined. Love to see it. Be back for the next one.
The only redundancy is emergency lighting as it's not needed when the generator is there however it's still nice to still have light during the 20 seconds before the generator starts as it allows me to still move around and stop whatever I'm doing safely
@@nics-systems-electricI have a demo system in my room - one board , messy and two systems in my house one basement and one my bedroom and the one in my bedroom is the P2R/W L on code 3 no sync module but the P2R/Wls don’t need sync modules on 2 devices
Would like to see the security system tested on the garage I recently installed a DSC NEO on my house and would like to see testing to see how you do it. This could be a separate video. Thank You
Regarding your comment about your generator videos: I actually discovered your channel through that content as opposed to your more popular FA videos. I’d love to see more.
Would it be possible to enable audible silence on just the chime strobe? Maybe it would be nice to know if the garage building is still in alarm without the noise after you silence it.
Hi Nic, is there a use case and/ or method of generator being monitored for it starts up like in a building when the power goes out and the generator like supervisory condition ? I enjoy your videos.
Yeah it's a requirement for generators supplying life safety power for a fully legal generator it needs to be supervised for running as well as low fuel and other trouble conditions in order for it to be considered a legal power source that will change your fire alarm battery calculations
09:25 For a second I thought your Garage Building B fire alarm system went off again from a detector that randomly activated like from last time but it turns out it's from the System Sensor P2W horn strobe installed in some sort of storage room of your house where that exit sign is as it kinda creates confusion when you're outside and the fire alarm goes in in the garage or in the house as it's confusing of which system activated as to better avoid that confusion replace the P2W with an L-Series set on the 3K tone because it allows you to tell the difference of which System activated but in a minor part of your house when you're outside as the 3K tone isn't needed on the garage System because they're a major part of the building. And this can be useful to tell the difference if both systems activated at the same time
@@nics-systems-electric Just looking at the panel's manual. And what I found on Page 12 of the manual, it says that when it is flashing "Signals Silenced" like that it means that there are some outputs that are off and some that are on. And that's due to the fact that you have the NAC 3 set on something else so right now it is not energized with an Alarm state like NAC 1 & 2 are.
@@nics-systems-electric Almost all openers (except some of the latest models) just use dry contacts for the wall button. Add a magnetic reed switch (to tell if the door is closed or not) and then a relay could activate the button. That should be reliable enough but won't work if the door is only partially open. A more reliable way could be to hold the safety sensor circuit open while the alarm is active and pulse the button. That should only fail if the door is already moving the moment the alarm comes in.
@@nics-systems-electric You must have one of those super-new ones then. You could still solder a pair of wires across the actual button in the controller if you really wanted to.
If i was you i would keep the 2 in main foyer of garage and washroom and the generator and outside and get rid of the non needed ones and you most Definitely need one in Furnace/Fire Alarm Panel Room
Nick Are you going to place a switch after the fuse holder to prevent electric shock when plugging the the fuse back in to restore from testing the generator.
You should make it so that when you silence the garage system, the chime strobe silences but the amber strobe keeps flashing until the garage system is reset.
I know you did a tutorial of how to wire a pull station non addressable to a horn strobe but could you possibly do another but with a non addressable fire light dual action pull station and a different horn strobe?
Hi, I have an NFS 320 notifier fire alarm panel with 138 smoke detectors and 25 modules. Now my panel is showing multiple trouble"INVERB". The same device showing "inverb" trouble blinks a green colour as a normal device, sometimes the same device blinks a red colour and sometimes the same device keeps the LED red in colour. Could you please suggest to me your expert advice?
For May 1st inspection have somebody help you with the testing. And set the house in the garage off at the same time. The second person will pull one on the inside switches. Why you do the other
Why did you replace your Led alarm back to the strobe and I expected you replaced your advances in the building with L series Strobes and also you have a bathroom in your house are you gonna put a remote strobe in there
@@nics-systems-electric your just like me then, i pretend, act, and think im a fire marshall, but in reality im just an unpaid assistant, but the thing i get "paid" with gifts do :/
@@HydraBOOM120 I don't pretend to be a fire marshal i've never claimed to be one. I am apprentice electrician that's what I do. depending on the company you're with you will often be handling lots of fire alarm as an electrician and working closely with technicians.
@@Corwin09-ji8sx you asked so I told you... currently almost all of British Columbia is at very low or low danger rating however that has nothing to do with my April fools video.
Some people would say having commercial-grade safety systems installed in a residential structure is redundant and unnecessary. Way i see it as thats probably the most fire safe house in your county, and its your house, you do what you want with it. I would love to do something like this myself to my house honestly. Problem is i dont own one yet 😂.
At the bare minimum if that equipment never really helps you in an incident [though I know at least the power backup and emergency lighting systems have], the experience and knowledge gained from doing all that work - very clean and professionally done by the way - is more valuable than all of the equipment monetary costs combined.
Love to see it. Be back for the next one.
Thank you I appreciate the support! That's exactly how I see it myself.
loved it😊😊 thank for sharing your experience and your experience
Dude has backup lights and a monitored fire alarm system and strobe in the shed. Man we should all be this protected.
No kidding. But it is major overkill lol so much redundancy
The only redundancy is emergency lighting as it's not needed when the generator is there however it's still nice to still have light during the 20 seconds before the generator starts as it allows me to still move around and stop whatever I'm doing safely
@@nics-systems-electricI have a demo system in my room - one board , messy and two systems in my house one basement and one my bedroom and the one in my bedroom is the P2R/W L on code 3 no sync module but the P2R/Wls don’t need sync modules on 2 devices
You should pull the fire alarm pull station next to the main control panel next system test
You should pull the fire alarm pull station next to the main control panel next system test
Good video, I think that you should do the pull station by the panel in the house, and the shed heat detector for the garage.
Great video. Activate the garage with the pull station in the pool shed. Activate the house with pull station in the shed under the porch.
I have to tell you, Nic. I’m one of the few people who actually find your generator videos to be SUPER interesting, so keep on making them!
Awesome, thank you!
Awesome. On your May test. For the house system can you do the pull station in the shed
Great one nic
Would like to see the security system tested on the garage I recently installed a DSC NEO on my house and would like to see testing to see how you do it. This could be a separate video. Thank You
I did a test not too long ago I may do one again at some point just not something I show much as I do not have much knowledge on it
Love the vids, keep it up. Waiting for the next install! Love the install videos.
Thank you I'm glad you enjoyed
@@nics-systems-electricUPLOADD EVERYDAYYYY
@@nics-systems-electricI LOVE YOUR VIDSSS
Regarding your comment about your generator videos: I actually discovered your channel through that content as opposed to your more popular FA videos. I’d love to see more.
Me who found him by the railroad crossing video: 💀
Would it be possible to enable audible silence on just the chime strobe? Maybe it would be nice to know if the garage building is still in alarm without the noise after you silence it.
I don't believe it's an option on these Canadian panels I could be wrong though
@@nics-systems-electric wait but dont those panels be the same here in the US? or no?
@@HydraBOOM120 this is a 320C the C is for Canadian it is different than the US model
You should do the duct detector in the house again!
Awesome job as always Nic
Hi Nic, is there a use case and/ or method of generator being monitored for it starts up like in a building when the power goes out and the generator like supervisory condition ? I enjoy your videos.
Yeah it's a requirement for generators supplying life safety power for a fully legal generator it needs to be supervised for running as well as low fuel and other trouble conditions in order for it to be considered a legal power source that will change your fire alarm battery calculations
@@nics-systems-electric thanks
09:25 For a second I thought your Garage Building B fire alarm system went off again from a detector that randomly activated
like from last time but it turns out it's from the System Sensor P2W horn strobe installed in some sort of storage room of your house where that exit sign is as it kinda creates confusion when you're outside and the fire alarm goes in in the garage or in the house as it's confusing of which system activated as to better avoid that confusion replace the P2W with an L-Series set on the 3K tone because it allows you to tell the difference of which System activated but in a minor part of your house when you're outside as the 3K tone isn't needed on the garage System because they're a major part of the building. And this can be useful to tell the difference if both systems activated at the same time
You can tell which system if there is strobe going off on the garage that's why there is a blue strobe for building annunciation
Are you going to add to the house system a couple of co alarms and a a strobe on the front of the house ?
No because CO detection is not necessary and outside strobes are too aesthetically not pleasing
There is no gas in the house so whats the point
who wants to see him collab with ser safety?
Why was the "Signals Silenced" LED flashing on the panel for the house? It never usually does that... does it?
You'd have to give a timestamp to see which you are referring to
@@nics-systems-electric 10:31 It was flashing with the "Fire Alarm" LED
@@IanGSully yeah, I'm not sure why
@@nics-systems-electric Just looking at the panel's manual. And what I found on Page 12 of the manual, it says that when it is flashing "Signals Silenced" like that it means that there are some outputs that are off and some that are on. And that's due to the fact that you have the NAC 3 set on something else so right now it is not energized with an Alarm state like NAC 1 & 2 are.
@@IanGSully interesting thanks for the research
What tome do you have the System Sensor L-series horn strobe in the main garage set to?
All of them are on low
What do the notifications look like on your phone? (What do they say, what pictures do they have if any, what system is in alarm, etc)
No detailed information just a power loss but I showed that in both of my videos on installing it in the garage and house system
Dude that's awesome!
Thank you
What did Jackson do that got him banished to the back yard?
That LF horn strobe closest to the panel really makes the wall vibrate lol
Because he's freaking out and being an ass. I think the F clips need to be tightened on the box
Idea for another update. You can have the garage door open automatically, when the CO alarm goes off.
If residential garage doors had contacts that could be tied into
@@nics-systems-electric Almost all openers (except some of the latest models) just use dry contacts for the wall button. Add a magnetic reed switch (to tell if the door is closed or not) and then a relay could activate the button. That should be reliable enough but won't work if the door is only partially open.
A more reliable way could be to hold the safety sensor circuit open while the alarm is active and pulse the button. That should only fail if the door is already moving the moment the alarm comes in.
@@eDoc2020 mine does not operate with a dry contact
@@nics-systems-electric You must have one of those super-new ones then. You could still solder a pair of wires across the actual button in the controller if you really wanted to.
Oh wow nice sneak peek of the new addition ;-----)
for the garage, you should use the tower pullstation if it is still there
It isn't
Nic have you tried that trick I told you about with air freshener and the CO detector?
I have not yet
Whats the trick
@@DanTDMJaceyou spray air freshener on a CO detector and it’s supposed to go off
@@Harper_DobniYT Pretty sure that could damage the detector. There's a reason they make detector-rated sprays
Nice Great video
Thanks
If i was you i would keep the 2 in main foyer of garage and washroom and the generator and outside and get rid of the non needed ones and you most Definitely need one in Furnace/Fire Alarm Panel Room
Have you ever thought about replacing the KDM-R2 with an NCA-2 on the house system?
No as it makes programming difficult or impossible without using verifier
@@nics-systems-electric Yeah that’s true.
i want to see the pull station in the house. love the video
Which one? There's four of them and we did one in this video.
@@nics-systems-electric the one in laundry room
Great videos you have
Bring the fog machine back
I think you should try testing heat detectors next month. Not the attic ones but the addressable ones
Trying to find the video on installing a massive lever switch on the demo board
27:53 You should buy a muzzle for Jackson if you want to stop him from barking for no reason
That's not what they are meant for
2:20 how about put feu fire once out side the house
Great video
U should do a drill test on the annunciator
I could do it separately however it can't be used as the monthly test as it's not a legal test
Let’s see for may tests
For the garage: the pull in the storage shed
For the house the smoke by the front door
22:33 POV: nick thinking on a good aprils fools joke but then remebering that the video is coming out later
Nick
Are you going to place a switch after the fuse holder to prevent electric shock when plugging the the fuse back in to restore from testing the generator.
I just talked about that because people keep complaining and explained it
You should make it so that when you silence the garage system, the chime strobe silences but the amber strobe keeps flashing until the garage system is reset.
How would that be possible
I know you did a tutorial of how to wire a pull station non addressable to a horn strobe but could you possibly do another but with a non addressable fire light dual action pull station and a different horn strobe?
It's the same thing
Hi, I have an NFS 320 notifier fire alarm panel with 138 smoke detectors and 25 modules. Now my panel is showing multiple trouble"INVERB". The same device showing "inverb" trouble blinks a green colour as a normal device, sometimes the same device blinks a red colour and sometimes the same device keeps the LED red in colour. Could you please suggest to me your expert advice?
Do you have alarm in your house for carbon monoxide?
No not necessary
Amazing video
Thanks
1/4 of the way to 100K nice
👍👍👍👍👍👍👍👍👍👍👍👍 that's for you nic
For May 1st inspection have somebody help you with the testing. And set the house in the garage off at the same time. The second person will pull one on the inside switches. Why you do the other
Nice
Your dog cool
Awesome
Do a Bring in your garage, even the high 1:22 1:23
On the next test you shoukd set the house system off using the T-bar by the panel
Next time please set off the tower pull-station!
Part I loved about the video
00:00 - 30:09
Why did you replace your Led alarm back to the strobe and I expected you replaced your advances in the building with L series Strobes and also you have a bathroom in your house are you gonna put a remote strobe in there
No I never had LED alarms up
@@nics-systems-electric are you gonna replace the advance strobes into the L series Strobes except the Outside ones?
@@Earth_Number_12 probably not
Where’s the annunciatior for garage
There isn't one it's not needed
😮😮
Nick we had power outage six times at our house
there are two types of dogs hearing the fire alarm or smoke alarns
ayla (calm dogs) 😇😇😇😇😇😇😇😇😇😇😇😇
jaxson (the angry dogs)🤬🤬🤬🤬🤬🤬🤬🤬🤬🤬🤬🤬🤬🤬🤬🤬🤬🤬🤬🤬
Nick do the house and the garage in May
I do them both once a month
Nj and nyc and Long Island had a 4.8 earth quake at 1036 it went off when I was in a meddle of a test!
Hey how are you this weekend
Hard to tell just started
What salary do you make a month in Canada as a fire Marshall
@@fortniteinminecraftt3794 I have no idea I'm not one
@@nics-systems-electric your just like me then, i pretend, act, and think im a fire marshall, but in reality im just an unpaid assistant, but the thing i get "paid" with gifts do :/
@@HydraBOOM120 I don't pretend to be a fire marshal i've never claimed to be one. I am apprentice electrician that's what I do. depending on the company you're with you will often be handling lots of fire alarm as an electrician and working closely with technicians.
average girl: hey I have a tree house in my yard what do you have
nic: a substation
Its funny how nick has summer and i in sweden has snowstorm and -10 celsius
Hey, Nic, when I was talking to my friends today, they ran away from me! Why? I feel bad about that!
Sounds like a them problem
@@nics-systems-electricOkay! What do you mean?
@@Camporito25 it's their problem
@@CGray1234 How is it their problem
@@Camporito25 They're just bad friends
Yo Wsp nic!
Hi
Under 1 hout club join here
👺👺👺👺👺👺👺
Cringe
8:38
1 hour or less team
Yes
Cringe
Hello😊
Next month activate both the fire alarm system and carbon monoxide system at the same time
Says it’s not a 30 minute test ends I’d being 30 minutes long
Wassup nic how is your weakend right now
Yea
edwards integerty and wheelock ns
do a drill
Can't use drill as a monthly test that does not count
@@nics-systems-electric he/she meant as in the NEXT video you upload
@@HydraBOOM120 I'm aware of that however you cannot use the drill button as a functional test
@@nics-systems-electricdo the drill button
@@dustinkey8885 as I said doesn't count as a test
duct detector in the house and bathroom detector in building b
😂
The so-called fire in your shed was a fake, and was only meant for April Fools. Right?!
April fools
@@nics-systems-electricOf course it was made for April Fools, but the wildfire risk getting higher in the U.S and Canada is real.
@@Corwin09-ji8sx you asked so I told you... currently almost all of British Columbia is at very low or low danger rating however that has nothing to do with my April fools video.
First lol.
Cringe
Cringe
whats wrong with saying "first"?, we ALL do that, stop acting like he/she said the "hard-R"
@@HydraBOOM120 i agree lol
@@HydraBOOM120 💀nobody is acting like anyone said the hard r
I hate fire alarm.🚨🔈🔉🔊
Don't watch the videos then