I watched tons of mounting installation videos and NO ONE covered the detail that you did. Searched everywhere for those black circle pieces that you can use for uneven walls (if needed) they are not even mentioned! Your video was extremely detailed and made my install a success!! THANK YOU
Got this tv and hired an installer through the Samsung website and set up to have them come out 5 days after it was supposed to get here in the morning. Now there’s a delay and of course the tv can be delivered just a few hours after my installation appointment. Try to reschedule and it’s 2 more weeks out. Then I think why am I going through all this. I installed a movable wall mount and the same size tv last time. I can do this. So here I am. Grew up with an extremely handy and mechanical brother and sister, so I’ve always thought of myself as incapable. But forget that! I’ve been doing all kinds of stuff since I bought my house 2 years ago. Thanks for the video. It’s very straightforward
Super helpful video - thank you! Just a heads up for those who have a 50 inch frame - the measurements provided by Samsung were materially off for the measurement labelled "D" for my TV (2022 frame, 50inch). It states 566mm on the sheet, but it is actually more like 547mm-ish. I would recommend doing the following before using the Samsung measurement blindly: place the brackets on the TV in the exact same position that B The Installer does at the start of the video (with the screw in the middle of the 3 leaf clover thingy). Then, with your TV resting on the ground, attach the wall brackets to the TV bracket and position it how it would theoretically hang on the wall. Perform the 'D' measurement manually with a tape measure to confirm the true measurement. This was 547mm for me and not the 566mm stated. This might not be a huge difference, but I had some drywall holes near the lower end of my desired final TV hanging space and if I had used Samsung's 566mm provided measurement, the holes would have showed. Anyway - good luck all, thanks again for the video!
I'm an installer and have done this tv once before. I have another one to do today and wanted to brush up on it. Your video is nice and detailed. This video will help me move faster during installation. I just wonder how in the world does Samsung push all of that power and data through a single cable!
Great installation video! My wife and I treated ourselves to the same 75” Frame TV that you demonstrated. I’ve hung a number of flat screen TV’s over the years, bet never a Frame. I didn’t know about the separate controller box-it makes total sense with the overall design of the TV. Now I’ll be able to get the installation location prepped properly Thanks, again!
Seems like B the Installer is really the best installation coach on TH-cam! For a non-handy guy like me super helpful. Thanks a lot and continue to motivate us to understand how things are done properly.
The One Wire is a game changer to replace existing TV with prior premiere installs having all the ports and boxes already installed behind the TV and client wanting TV to be flush to wall. Good to know that reworking wall and old wires will add time to install. One Wire looks great for new location. Thanks for the how to tips! I had not done a flush mount until today and the client has stuff from old system. Good job on everything!
I noticed you installed the toggle bolts in horizontally versus vertically. For the correct weight load distribution, the metal tabs need to be vertical to support the advertised weight of the toggle bolt. That is very important. Installing them with the metal tab horizontally reduces the weight the toggle can support and could cause a heavier tv to fall off the wall. Just an FYI. I use to install these in best buy stores for years.
Just so everyone is clear on this... 1. The toggle bolts will hold most weight vertically, but if you have two, one above the other... the metal hits metal when placing them vertically so it's best to angle them a little. 2. The weight of this tv is not a concern, 4 toggle bolts can hold a 300 LB tv, which this is not. Glad people enjoy the video and are saying attention. 😀 ✌️
Compreshensive intructional video. Thanks! Even without the template, using the Samsung provide directions he references: A=3.2 down and B= 8.6 in or whatever, along with this made the install clear. Then double check with the template, if you have it. As he mentions in the video, as long as the two brackets are the right distance apart (also a letter-identified measurement on the Samsung diagram, the self-leveling capacity of the brackets sliding on the slippery stick-on pieces should level it out. Don't be afraid! You got this. TIP: Depending on the size of the screw head you use, you might want to buy some smallish washers. The large-headed black screws provide are fine, if you're fastening to a stud. However, the oblong holes in the mounting plates are fairly wide, up and down, and small screw heads slip right through.
Thank you for this very helpful video! Your demo is 100% better than the instructions from Samsung - it enabled us to the Frame TV above our fireplace mantle without any issues.
Thank you for your expert guidance. We followed your directions and were successfully able to mount our 55-inch Frame TV. Much better than the directions provided by Samsung!
Make sure you put the black plastic film in the square pockets. It is used as a slider after all is installed on the wall. It let's you do a final level just like a picture on the wall. Hope Samsung reads some of the comments. There are tiny fixes that need to be made.
My microphone is off but I’ve already hung the TV. It’s a 2024 Frame TV bought in April 2024. Where do I find the microphone switch on the back of the TV, and can it be reached without taking the tv off the wall?
Subscribed! Thankful! You have helped so much! 2 Questions 1) Can you use a different drill bit for 3/16in toggle bolts? I only have 1/4in as my biggest bolt. 2) What drill bit do you use if you have a stud? This would be helpful to help me finish.
Thanks for this amazing video. We bought a 65" open-box Frame last weekend, and, using this video I was able to put it up on the wall with no issues! Also, thanks for the zoom of the B and D measurements so I could get them for my TV!
It's too bad samsung split the wall bracket up into 2 small parts, if it were one big one you would have been able to drill right into studs and the whole install would have been a lot easier.
This, as all things in the world, is explained by money. If they were to have one single piece, they would have to make different mounts for all tv sizes. Having two pieces, they are one size fits all. Easier and cheaper production
Probably worked this out already but if it's 3mm at the bottom and 25mm at the top, the hooks are probably not snapping down into the bottom part of the latch. It requires more force than reasonably expected. A Samsung forum poster recommends removing the hooks from the TV to snap them on and off a couple of times before handing the TV.
Hey awsome video. I am going to be mounting my 55" fram tv onto a plaster wall above fireplace mantel. Behind the plaster is brick chimney. Would you have any tips on what to use for mounting this way?
Thanks for this video. I used it to hang 2 Frame TVs. Question: I need to hang an 85lb 2’ wide wall mirror. It has two strap hangers on the back and says don’t use a wire. To center it I can’t hit a stud, only drywall. Do you think the 100lb Adjustable J-Hooks (50lbs each) on Amazon could really do it? Instead of using the included 2 nails each hook into the drywall I could use 1 toggle bold each hook. And as a backup, if they failed, I could have a 100lb wire to catch on a nail into a stud (not centered). I just can’t believe drywall can hold so much weight. Thanks. This video was my go to video form both my 55” and 65” Frame TVs.
Thank you for the video. Great instructions. I drilled in 3 toggle bolts you recommended but on 2 of them, the screw doesn't grab on to the back end. It's just loose. Only 1 of the toggle bolts grabs on and I can tighten that one. Any idea why the other 2 don't tighten correctly?
Hung up my 2022 Frame thanks to your videos. I did a bunch of research and found an easy solution for the One-Wire. I used "Thermoflex Flexo F6 Flame Retardant, 3/8" (1/4" would work too) around the One-Wire. Easier than a plastic conduit. Obviously, you can just not do anything, but thought I'd share another solution. Also, have you had an issue with the TV not sitting flush against the wall within the bracket? Mine looks like it's very slightly angled down. I read online that some people have had a problem with this. I don't want to force the TV all the way down in the bracket for fear of damaging the TV.
I recently installed our model (thanks b the installer!!!) and did some poking around prior to hanging the TV up. The hook that goes onto the mount need to "click" when you slide it on vertically. Those metal tabs on the mount makes the hook snug once it's in place, so you can't just slide the TV on and let it rest against the wall. You need to pull it down when sliding the hooks hang onto the mount and hear some clicks (which means the tabs have made room for the hooks). I think a fix for your current setup is to slide your TV up, angle it outwards to get some viewing room where the hooks are, and slide it back down and listen for the click. You need to use a little force 😅 but I get that it can be scary. Best of luck!! Mine is flush against the wall after doing the above 😄
Fantastic instructional video. Thanks! Definitely use the longer screws for the part of the mount that screws into the back of the tv if you have electrical or hdmi outlets on the wall that the tv will be hanging over. He mentions this towards the end of the video, but in case anyone doesn’t make it that far…
Thanks! Got it done in under an hour thats to your video. Appreciate the simplicity while still touching on everything needed to get it done accurately.
Hello from Netherlands! I have almost the same configuration (same anchors and same wall mount). However, I'm still unsure about hanging my 85" Samsung on the drywall. Do you think it's safe with 85" as well?
Mate.... Moved into our new home, (my missus and I) bought a frame tv, we're wanting to put up acoustic panel slats on our TV wall. Your vid has helped out heaps. With the slats being 20ml thick, I'm thinking the flush wall mount won't suffice. Any thoughts on raised mounts that will work with the Frame tv 65inch?? New fan and subscriber from Darwin NT Australia 🇦🇺 Ps: Don't spose you do outcalls to Aus? Cheers mate 👍
Definitely get that in-wall rated cable. Yes I know it seems like a pain, cuz it is, but in the event of a home fire, it could end up being the difference between your insurance company covering it or not. Definitely worth the price then. To be honest, with how Samsung seems to intend for this to be installed, I think it's kinda stupid that they even supply a cable that isn't in-wall rated and then make you buy the other one for an extra fee. Just supply every one with the in-wall rated cable so people don't get confused.
The in-walp cable is much thicker and looks bad externally. The thin wire they provide is barely visible if outside wall. This is at least 1 year ago anyways. The one wire is thicker on other models.
@BTheInstaller I am confused! There must be two separate cables! One is the cable that runs from the ONE Connect Box to the TV and the other is the power cord that runs from the ONE Connect Box to the power outlet. If run within walls, would not both of these cables need to be in-wall rated? Now, we intend to mount a box behind the television to house the One Connect Box. To just run the cable from the tv to the One Connect Box that sits directly behind the tv, I would not think an in-wall rated cable would be required. Or would it? That still leaves the power cord that runs from the Box to the wall outlet. Is this power cord in-wall rated or must one be purchased? Thanks for your help.
After checking out those toggle bolts you recommended, it says right on the package "Do not use for mounting televisions".... curious why you use them then?
What size low voltage box would be needed to mount the one connect box inside the wall behind the 85" Samsung Frame? Thanks for ALL the help you give us DIYers!
Did you ever figure out the low voltage box size and where did you purchase it? My daughter needs me to mount her controller in a recessed box since it is being mounted over a fireplace and she has nowhere to put the controller other than in a recess.
@@JT_70 I decided to go a different route. But I did find this on Amazon…”Legrand - OnQ 17 Inch Media Enclosure”…but I didn’t use it, so double check that it will work.
Can the wall mounts that come with the TV allows it to be mounted on a portrait mode? Can the brackets that attach to the TV be attached in a way that allows the TV be hanged down on a portrait mode?
Hi, just purchased this TV in 55, looking as if mounting could be a problem as power, internet/Ethernet and antenna connections are on the wall behind where I plan to install the frame and was suitable to our old tv design. I assume the Ethernet is not required any more, just go wifi but the antenna connection sticks out as also the power connection. I’ll use a remote power connection, just stumped about the antenna? Any suggestions, I’d upload photos if I could
Great video. Tonnes of help. Will do the install myself now. Strongly suggest people play around with the wall bracket piece and the square tv bracket before installing them to the wall and t.v.. You'll see how to hang the tv bracket, close the bracket, then raise it slightly to see how the magnet in the tv bracket strongly grabs the tv bracket to the wall bracket. Pretty cool how it is designed. You'll also see how to lift the bottom of the tv bracket to get it to release from the wall bracket.
We use toggle bolts on plaster and lath to hang floating shelves that hold books. They work great! We haven’t installed our mount yet but plan on using toggle bolts.
I just installed a Samsung The Frame 55" and found the included instructions and template to be awful. As far making it easy to mount the tv where you want it - if you, say, think you want to mount it 61" on center from the floor, the template isn't marked to show you how far up from the brackets you're mounting that the tv will sit It doesn't even give you a centering line. And I would say most people want to know how far off the ground the tv will sit or if it's centered on a wall or in a particular space. I should also note: I'm a carpenter and I mount a lot of tvs for clients as a courtesy after punch listing a job, so it's not like this was my first rodeo. I got it done - no thanks to Samsung - but for the many DIYers out there who might not have the experience, you're video should be a big help.
How wide are the wall bracket pieces? I’m looking to buy this to buy I have an outlet on the wall that might get in the way of the bracket. Wanted to get those measurements before I purchase and realize it won’t work.
Great video. Interesting that the one connect box cable is not wall rated as a lot of people are going to want to hide it in a wall. It seems as though Samsung made a wall version, but I can’t seem to find one to purchase. Is there a workaround for this or do you basically have to go against code to do it?
@BTheinstaller I have a customer who wants to put F TV over the GAS fireplace. This fireplace HAS a chimney to the roofline. There is a window on each side of the fireplace which means there will be at least 4 1/2" of lumber between the window. You have made it look so easy she didn't understand why I couldn't simply run the wire into the wall and out at the bottom. Can you come to Michigan and explain? LOL
I’m on the search for toggle bolts in the size you mentioned with flathead screws but can’t find. I too will have to use them as the studs aren’t where I would need to center the tv
I used your video to hang my 2 frame TVs 65” And 55” but now I wonder if all this was necessary. Have you seen the 3M Claw 65 hooks? It’s crazy that you could used two of these to hang a frame TV into drywall only… and have almost no mark on the wall of you ever took it down.
Quick question I just did the day before yesterday a 65 inch Samsung now with the rear bracket, on the back of the bracket it says rear bracket to the right and it has one to the left. He put the right on the left and the left on the right, all the measurements was good but he kept getting an error so all he really did was slid the mount over so that it could latch on. I think that’s what he did wrong. He had them on backwards the opposite way if he would’ve listened to me he would have no problems, but he didn’t want to listen, am I correct?
Super helpful video that clears up some of my questions. But I’m planning to install my Samsung 55” Frame TV on a wall with wood panelling. Any suggestions about working on this uneven surface?
With this install the 'One Box' is inside a cabinet, and I am assuming the remote control still works. Does this mean it is not using IR to communicate with the box? If so, does anyone know how this works? I would like to install the One Box in the room behind the wall (single layer brick). My only other option is to have the cable coming down the wall as there is no cavity for me to be able to chase the cable into the wall and install the box anywhere else. Thanks
I guess im a little wacky, i usually measure from floor or top of the stand to find a mounting area . My apt is 97 years old and the building itself isnt even level lol. Also , Why not just use the level to draw a guide line straight across?
Amazing video, much more confident now. You had to level the TV after hanging it. Does that mean you have a little wiggle room after hanging it as well, without adjusting the back brackets?
Great Installation Video, well done! That said, I am looking to replace my 2010 Vintage LG TV but was hoping I could re-use my pre-existing mount as it is attached to a brick fireplace wall.
Check out how to make your own website and run your small biz @ www.squarespace.com/btheinstaller
You mentioned 1/4 toggle bolts. But what size did you actually use in this video?
I watched tons of mounting installation videos and NO ONE covered the detail that you did. Searched everywhere for those black circle pieces that you can use for uneven walls (if needed) they are not even mentioned! Your video was extremely detailed and made my install a success!! THANK YOU
Got this tv and hired an installer through the Samsung website and set up to have them come out 5 days after it was supposed to get here in the morning. Now there’s a delay and of course the tv can be delivered just a few hours after my installation appointment. Try to reschedule and it’s 2 more weeks out. Then I think why am I going through all this. I installed a movable wall mount and the same size tv last time. I can do this. So here I am. Grew up with an extremely handy and mechanical brother and sister, so I’ve always thought of myself as incapable. But forget that! I’ve been doing all kinds of stuff since I bought my house 2 years ago. Thanks for the video. It’s very straightforward
Super helpful video - thank you!
Just a heads up for those who have a 50 inch frame - the measurements provided by Samsung were materially off for the measurement labelled "D" for my TV (2022 frame, 50inch). It states 566mm on the sheet, but it is actually more like 547mm-ish.
I would recommend doing the following before using the Samsung measurement blindly: place the brackets on the TV in the exact same position that B The Installer does at the start of the video (with the screw in the middle of the 3 leaf clover thingy). Then, with your TV resting on the ground, attach the wall brackets to the TV bracket and position it how it would theoretically hang on the wall. Perform the 'D' measurement manually with a tape measure to confirm the true measurement. This was 547mm for me and not the 566mm stated.
This might not be a huge difference, but I had some drywall holes near the lower end of my desired final TV hanging space and if I had used Samsung's 566mm provided measurement, the holes would have showed.
Anyway - good luck all, thanks again for the video!
I'm an installer and have done this tv once before. I have another one to do today and wanted to brush up on it. Your video is nice and detailed. This video will help me move faster during installation. I just wonder how in the world does Samsung push all of that power and data through a single cable!
Great installation video! My wife and I treated ourselves to the same 75” Frame TV that you demonstrated. I’ve hung a number of flat screen TV’s over the years, bet never a Frame. I didn’t know about the separate controller box-it makes total sense with the overall design of the TV. Now I’ll be able to get the installation location prepped properly Thanks, again!
@BTheInstaller do you have a link for the dry wall anchor bolts you mention during the Tools portion of this install?
Seems like B the Installer is really the best installation coach on TH-cam! For a non-handy guy like me super helpful. Thanks a lot and continue to motivate us to understand how things are done properly.
⬆️⬆️⬆️⬆️Thanks for watching and leaving a comment, you have been selected among my shortlisted winner's 🎁🎁 hit me up to claim your price,,
The One Wire is a game changer to replace existing TV with prior premiere installs having all the ports and boxes already installed behind the TV and client wanting TV to be flush to wall. Good to know that reworking wall and old wires will add time to install. One Wire looks great for new location. Thanks for the how to tips! I had not done a flush mount until today and the client has stuff from old system. Good job on everything!
Good job covering everything. Would have been nice to see the side view to see how flush it is to the wall after new install.
Out of curiosity which toggle anchors are you using? Want to make sure I get the proper ones. There seem to be so many out there.
I noticed you installed the toggle bolts in horizontally versus vertically. For the correct weight load distribution, the metal tabs need to be vertical to support the advertised weight of the toggle bolt. That is very important. Installing them with the metal tab horizontally reduces the weight the toggle can support and could cause a heavier tv to fall off the wall. Just an FYI. I use to install these in best buy stores for years.
Ay thank you!
What toggle bolts do you recommend? I was planning to post for OP and saw your comment so whoever replies the fastest 😂🙏🏻
Just so everyone is clear on this...
1. The toggle bolts will hold most weight vertically, but if you have two, one above the other... the metal hits metal when placing them vertically so it's best to angle them a little.
2. The weight of this tv is not a concern, 4 toggle bolts can hold a 300 LB tv, which this is not.
Glad people enjoy the video and are saying attention. 😀 ✌️
Compreshensive intructional video. Thanks!
Even without the template, using the Samsung provide directions he references: A=3.2 down and B= 8.6 in or whatever, along with this made the install clear. Then double check with the template, if you have it.
As he mentions in the video, as long as the two brackets are the right distance apart (also a letter-identified measurement on the Samsung diagram, the self-leveling capacity of the brackets sliding on the slippery stick-on pieces should level it out. Don't be afraid! You got this.
TIP: Depending on the size of the screw head you use, you might want to buy some smallish washers. The large-headed black screws provide are fine, if you're fastening to a stud. However, the oblong holes in the mounting plates are fairly wide, up and down, and small screw heads slip right through.
Thank you for this very helpful video! Your demo is 100% better than the instructions from Samsung - it enabled us to the Frame TV above our fireplace mantle without any issues.
Great video. Do you have a link for the toggle bolts?
There is no way I will attempt this installation myself. Great video.
⬆️⬆️⬆️⬆️Thanks for watching and leaving a comment, you have been selected among my shortlisted winner's 🎁🎁 hit me up to claim your price,
You sir need a laser level!!!! Best tool I have ever purchased for hanging pictures or the tv.
I wish you had gone over the installation of the actual FRAME part and how it connects to the TV etc., overall great video and looks really good.
Thank you for your expert guidance. We followed your directions and were successfully able to mount our 55-inch Frame TV. Much better than the directions provided by Samsung!
Make sure you put the black plastic film in the square pockets. It is used as a slider after all is installed on the wall. It let's you do a final level just like a picture on the wall. Hope Samsung reads some of the comments. There are tiny fixes that need to be made.
wasn't there a video on putting the cable in a flexible conduit? link please!
My microphone is off but I’ve already hung the TV. It’s a 2024 Frame TV bought in April 2024. Where do I find the microphone switch on the back of the TV, and can it be reached without taking the tv off the wall?
THANK GOD I FOUND A PAGE LIKE YOURS!! SUBSCRIBED N READY TO LEARN !
Do you have a link for the toggle bolts your using. I’m installing a The Frame 55”
The included instructions were all but useless. This video saved my installation. Thank you!!!
I just got a super cheap deal on this tv, with the new one being announced, so thanks for the tips! I’ll definitely be tackling this myself!
Is there a suggestion to insulate the wire from fires?
Subscribed!
Thankful! You have helped so much!
2 Questions
1) Can you use a different drill bit for 3/16in toggle bolts?
I only have 1/4in as my biggest bolt.
2) What drill bit do you use if you have a stud?
This would be helpful to help me finish.
⬆️⬆️⬆️⬆️Thanks for watching and leaving a comment, you have been selected among my shortlisted winner's 🎁🎁 hit me up to claim your price..
Any suggestions for mounting over a fireplace given the required use of the 1 connect box.
For the plastic toggle bolts amd screw anchors, can anyone tell me if they are a specific size or brand? TIA
Really enjoyed the whole process! Thank you for all the details. Learned a lot.
Moved in new home and mounting on the wall above fireplace is not possible. Would like to just set it on mantle. Any suggestions? 2:22
Thanks for this amazing video. We bought a 65" open-box Frame last weekend, and, using this video I was able to put it up on the wall with no issues! Also, thanks for the zoom of the B and D measurements so I could get them for my TV!
⬆️⬆️⬆️⬆️Thanks for watching and leaving a comment, you have been selected among my shortlisted winner's 🎁🎁 hit me up to claim your price..
Do you have a video mounting the frame TV to a swivel mount? What’s the best way to mount the wall pieces to a swivel mount?
How did you pull conduit when I am sure there studs between the & outlet
It's too bad samsung split the wall bracket up into 2 small parts, if it were one big one you would have been able to drill right into studs and the whole install would have been a lot easier.
Exactly. Now you have to level between two separate mounts instead of one big mount. I like the lg G mount better
Agreed 💯 because if it were 1 piece 4 anchors would suffice instead of 8. So much more hassle and precision for split mounts 🤦🏻♂️
This, as all things in the world, is explained by money. If they were to have one single piece, they would have to make different mounts for all tv sizes. Having two pieces, they are one size fits all. Easier and cheaper production
It’s so you can use the same mount for different size TVs the template has marks for the different size TVs
Cost cutting
It does have an advantage being split in 2 for some folks where the outlet is centered on the wall behind the TV.
Hi there. Can you do a mounting installatuon for the Frame that rotates 2023 model ?
Help! I can't get the frame to hang 3mm from the wall as it shows in the instructions. There's almost 25mm space. :-(
Probably worked this out already but if it's 3mm at the bottom and 25mm at the top, the hooks are probably not snapping down into the bottom part of the latch. It requires more force than reasonably expected. A Samsung forum poster recommends removing the hooks from the TV to snap them on and off a couple of times before handing the TV.
⬆️⬆️⬆️⬆️Thanks for watching and leaving a comment, you have been selected among my shortlisted winner's 🎁🎁 hit me up to claim your price,
I just purchased the 2024 Samsung Frame TV 75 inch QLED 4K LSAO3D. Do you know if the installation is same as your video?
Do I need the the Samsung box when installing the 2023 frame if I have a Yamaha receiver, Fios for tv and apple tv?
26:20 - So you don't have to be 100% exact when drilling the mount into the wall, because you can still be able to level it out when its done?
Came to learn about the TV and I'm cracking up with the stairs and escalator fun... great job!
Hey awsome video. I am going to be mounting my 55" fram tv onto a plaster wall above fireplace mantel. Behind the plaster is brick chimney. Would you have any tips on what to use for mounting this way?
You mentioned that the tv was slightly off-level. What adjustment(s) did you make to correct it?
Thanks for this video. I used it to hang 2 Frame TVs. Question: I need to hang an 85lb 2’ wide wall mirror. It has two strap hangers on the back and says don’t use a wire. To center it I can’t hit a stud, only drywall. Do you think the 100lb Adjustable J-Hooks (50lbs each) on Amazon could really do it? Instead of using the included 2 nails each hook into the drywall I could use 1 toggle bold each hook. And as a backup, if they failed, I could have a 100lb wire to catch on a nail into a stud (not centered). I just can’t believe drywall can hold so much weight. Thanks. This video was my go to video form both my 55” and 65” Frame TVs.
Thank you for the video. Great instructions. I drilled in 3 toggle bolts you recommended but on 2 of them, the screw doesn't grab on to the back end. It's just loose. Only 1 of the toggle bolts grabs on and I can tighten that one. Any idea why the other 2 don't tighten correctly?
Hung up my 2022 Frame thanks to your videos. I did a bunch of research and found an easy solution for the One-Wire. I used "Thermoflex Flexo F6 Flame Retardant, 3/8" (1/4" would work too) around the One-Wire. Easier than a plastic conduit. Obviously, you can just not do anything, but thought I'd share another solution.
Also, have you had an issue with the TV not sitting flush against the wall within the bracket? Mine looks like it's very slightly angled down. I read online that some people have had a problem with this. I don't want to force the TV all the way down in the bracket for fear of damaging the TV.
I'm having the same problem with the top of my Frame leaning very slightly forward and not "locking" into place in the mount. :(
I recently installed our model (thanks b the installer!!!) and did some poking around prior to hanging the TV up.
The hook that goes onto the mount need to "click" when you slide it on vertically. Those metal tabs on the mount makes the hook snug once it's in place, so you can't just slide the TV on and let it rest against the wall. You need to pull it down when sliding the hooks hang onto the mount and hear some clicks (which means the tabs have made room for the hooks).
I think a fix for your current setup is to slide your TV up, angle it outwards to get some viewing room where the hooks are, and slide it back down and listen for the click. You need to use a little force 😅 but I get that it can be scary.
Best of luck!! Mine is flush against the wall after doing the above 😄
Hey where did you get the flexo F6 I can’t find it, and how did it workout for you?
@@elizaII Good tips thank you!
@@5sunny01 The Flexo F6 worked great. Super easy to wrap around the one-wire. I bought mine from a website called "Cabletiesandmore"
Recommendations for installing onto stacked stone (above a fireplace) ? Would masonry anchors be sufficient without a stud?
Fantastic instructional video. Thanks! Definitely use the longer screws for the part of the mount that screws into the back of the tv if you have electrical or hdmi outlets on the wall that the tv will be hanging over. He mentions this towards the end of the video, but in case anyone doesn’t make it that far…
⬆️⬆️⬆️⬆️Thanks for watching and leaving a comment, you have been selected among my shortlisted winner's 🎁🎁 hit me up to claim your price..
Thanks! Got it done in under an hour thats to your video. Appreciate the simplicity while still touching on everything needed to get it done accurately.
Super clear and well demonstrated. Bravo!
Do you have to use the black box? Like is the tv smart (Netflix, Hulu) without the box for ports?
Hello from Netherlands! I have almost the same configuration (same anchors and same wall mount).
However, I'm still unsure about hanging my 85" Samsung on the drywall. Do you think it's safe with 85" as well?
Mate....
Moved into our new home, (my missus and I) bought a frame tv, we're wanting to put up acoustic panel slats on our TV wall.
Your vid has helped out heaps. With the slats being 20ml thick, I'm thinking the flush wall mount won't suffice.
Any thoughts on raised mounts that will work with the Frame tv 65inch??
New fan and subscriber from Darwin NT Australia 🇦🇺
Ps: Don't spose you do outcalls to Aus?
Cheers mate 👍
newbie here. so what exactly are the risks you run when running wires that are not in wall rated in the wall?
Definitely get that in-wall rated cable. Yes I know it seems like a pain, cuz it is, but in the event of a home fire, it could end up being the difference between your insurance company covering it or not. Definitely worth the price then. To be honest, with how Samsung seems to intend for this to be installed, I think it's kinda stupid that they even supply a cable that isn't in-wall rated and then make you buy the other one for an extra fee. Just supply every one with the in-wall rated cable so people don't get confused.
The in-walp cable is much thicker and looks bad externally. The thin wire they provide is barely visible if outside wall. This is at least 1 year ago anyways. The one wire is thicker on other models.
@BTheInstaller I am confused! There must be two separate cables! One is the cable that runs from the ONE Connect Box to the TV and the other is the power cord that runs from the ONE Connect Box to the power outlet. If run within walls, would not both of these cables need to be in-wall rated?
Now, we intend to mount a box behind the television to house the One Connect Box. To just run the cable from the tv to the One Connect Box that sits directly behind the tv, I would not think an in-wall rated cable would be required. Or would it? That still leaves the power cord that runs from the Box to the wall outlet. Is this power cord in-wall rated or must one be purchased?
Thanks for your help.
After checking out those toggle bolts you recommended, it says right on the package "Do not use for mounting televisions".... curious why you use them then?
⬆️⬆️⬆️⬆️Thanks for watching and leaving a comment, you have been selected among my shortlisted winner's 🎁🎁 hit me up to claim your price..
What size low voltage box would be needed to mount the one connect box inside the wall behind the 85" Samsung Frame? Thanks for ALL the help you give us DIYers!
Did you ever figure out the low voltage box size and where did you purchase it? My daughter needs me to mount her controller in a recessed box since it is being mounted over a fireplace and she has nowhere to put the controller other than in a recess.
@@JT_70 I decided to go a different route. But I did find this on Amazon…”Legrand - OnQ 17 Inch Media Enclosure”…but I didn’t use it, so double check that it will work.
Can the wall mounts that come with the TV allows it to be mounted on a portrait mode? Can the brackets that attach to the TV be attached in a way that allows the TV be hanged down on a portrait mode?
Great video! I just installed the 75" Frame no issues thanks to B . Thank you
What do you recommend for a flush articulating mount?
Is the connect cord from tv to box shielded to run behind wall
Exactly what size toggle bolts did you use?
I know you don't really do soundbars but I'm interested in the s800b that goes along with this TV
Just bought two 85” Frame tvs (2022) and having them professionally installed next week
I wanted the 85” Frame, but I got the 75” instead. I couldn’t bring myself to spend an extra $1300 over the price of the 75” for the 85” one.
⬆️⬆️⬆️⬆️Thanks for watching and leaving a comment, you have been selected among my shortlisted winner's 🎁🎁 hit me up to claim your price,,
Hi, just purchased this TV in 55, looking as if mounting could be a problem as power, internet/Ethernet and antenna connections are on the wall behind where I plan to install the frame and was suitable to our old tv design. I assume the Ethernet is not required any more, just go wifi but the antenna connection sticks out as also the power connection. I’ll use a remote power connection, just stumped about the antenna? Any suggestions, I’d upload photos if I could
What is the link to purchase the toggle bots?
Great video. Tonnes of help. Will do the install myself now. Strongly suggest people play around with the wall bracket piece and the square tv bracket before installing them to the wall and t.v.. You'll see how to hang the tv bracket, close the bracket, then raise it slightly to see how the magnet in the tv bracket strongly grabs the tv bracket to the wall bracket. Pretty cool how it is designed. You'll also see how to lift the bottom of the tv bracket to get it to release from the wall bracket.
Hello, I can’t seem to get my tv flat and I never heard the click of the magnet. Is there anything else that I am missing?
⬆️⬆️⬆️⬆️Thanks for watching and leaving a comment, you have been selected among my shortlisted winner's 🎁🎁 hit me up to claim your price..
If mounting onto cinderblock would 3/8in x 4in Hex Washer-Head Large Diameter Concrete Anchors work?
I enjoy your videos. Thank you. We just got a 65” Samsung Frame tv and my hubby and I will install it ourselves, thanks to your info. 😊
Do you have a link on what to get to hide the Apple TV behind tv ?
Great video! Question... can you put the one box in basement directly below where tv is?
you can put it anywhere the cord will reach and jas power. the remote IR and Bluetooth to the tv.
Can you use those large bolts on plaster and lathe?
We use toggle bolts on plaster and lath to hang floating shelves that hold books. They work great! We haven’t installed our mount yet but plan on using toggle bolts.
if i have brackets mounted for a 65 inch do you think i can mount the 75 on it
Can you mount it so that it could be pulled out from the wall? 25:08
If the tv is slightly off level once on the wall, is there any pivot function to straighten it out?
Thanks for a great tutorial! Will likely set a new Frame up later this week. This video gave me a boost of confidence needed.
I just installed a Samsung The Frame 55" and found the included instructions and template to be awful. As far making it easy to mount the tv where you want it - if you, say, think you want to mount it 61" on center from the floor, the template isn't marked to show you how far up from the brackets you're mounting that the tv will sit It doesn't even give you a centering line. And I would say most people want to know how far off the ground the tv will sit or if it's centered on a wall or in a particular space. I should also note: I'm a carpenter and I mount a lot of tvs for clients as a courtesy after punch listing a job, so it's not like this was my first rodeo. I got it done - no thanks to Samsung - but for the many DIYers out there who might not have the experience, you're video should be a big help.
What size of toggle screws did you use? The one I got seems too big.
How wide are the wall bracket pieces? I’m looking to buy this to buy I have an outlet on the wall that might get in the way of the bracket. Wanted to get those measurements before I purchase and realize it won’t work.
Hoping to hear your thoughts/review of the 2022 version of the frame!
Great video. Interesting that the one connect box cable is not wall rated as a lot of people are going to want to hide it in a wall. It seems as though Samsung made a wall version, but I can’t seem to find one to purchase. Is there a workaround for this or do you basically have to go against code to do it?
⬆️⬆️⬆️⬆️Thanks for watching and leaving a comment, you have been selected among my shortlisted winner's 🎁🎁 hit me up to claim your price..
@BTheinstaller I have a customer who wants to put F TV over the GAS fireplace. This fireplace HAS a chimney to the roofline. There is a window on each side of the fireplace which means there will be at least 4 1/2" of lumber between the window. You have made it look so easy she didn't understand why I couldn't simply run the wire into the wall and out at the bottom. Can you come to Michigan and explain? LOL
I’m on the search for toggle bolts in the size you mentioned with flathead screws but can’t find. I too will have to use them as the studs aren’t where I would need to center the tv
I used your video to hang my 2 frame TVs 65” And 55” but now I wonder if all this was necessary. Have you seen the 3M Claw 65 hooks? It’s crazy that you could used two of these to hang a frame TV into drywall only… and have almost no mark on the wall of you ever took it down.
Hey, I just bought the flip toggle bolts for the wall by cobra and right on the back it says do not use for mounting televisions. What the heck?!
how long is the wire/cable coming out of the One Connect box? Thanks
Quick question I just did the day before yesterday a 65 inch Samsung now with the rear bracket, on the back of the bracket it says rear bracket to the right and it has one to the left. He put the right on the left and the left on the right, all the measurements was good but he kept getting an error so all he really did was slid the mount over so that it could latch on. I think that’s what he did wrong. He had them on backwards the opposite way if he would’ve listened to me he would have no problems, but he didn’t want to listen, am I correct?
The L one goes on the left as you're looking at the back.
Super helpful video that clears up some of my questions. But I’m planning to install my Samsung 55” Frame TV on a wall with wood panelling. Any suggestions about working on this uneven surface?
This was unbelievably helpful. Thank you!
We have a conduit tubing, is the cord safe in the wall with that?
⬆️⬆️⬆️⬆️Thanks for watching and leaving a comment, you have been selected among my shortlisted winner's 🎁🎁 hit me up to claim your price,
Great video, I used this to install my tv. However we want to decorate and I’m struggling to get it off the wall…. Any advise?
With this install the 'One Box' is inside a cabinet, and I am assuming the remote control still works. Does this mean it is not using IR to communicate with the box? If so, does anyone know how this works? I would like to install the One Box in the room behind the wall (single layer brick). My only other option is to have the cable coming down the wall as there is no cavity for me to be able to chase the cable into the wall and install the box anywhere else.
Thanks
Where can I buy those exact anchors?
⬆️⬆️⬆️⬆️Thanks for watching and leaving a comment, you have been selected among my shortlisted winner's 🎁🎁 hit me up to claim your price..
Any thoughts on the best brick/mason hardware to use? Turns out, 75% of my LR wall is brick (house was built in 39 and has had 2 remodels).
⬆️⬆️⬆️⬆️Thanks for watching and leaving a comment, you have been selected among my shortlisted winner's 🎁🎁 hit me up to claim your price,
glad to hear about the one connect box... would have been screwed for my setup on a brick wall fireplace
How long is the One-Wire? And what is the issue with running that behind a wall on its own? Is it a fire hazard?
⬆️⬆️⬆️⬆️Thanks for watching and leaving a comment, you have been selected among my shortlisted winner's 🎁🎁 hit me up to claim your price,,
I guess im a little wacky, i usually measure from floor or top of the stand to find a mounting area . My apt is 97 years old and the building itself isnt even level lol. Also , Why not just use the level to draw a guide line straight across?
Amazing video, much more confident now. You had to level the TV after hanging it. Does that mean you have a little wiggle room after hanging it as well, without adjusting the back brackets?
I'm curious about this too.
⬆️⬆️⬆️⬆️Thanks for watching and leaving a comment, you have been selected among my shortlisted winner's 🎁🎁 hit me up to claim your price,,
Great Installation Video, well done! That said, I am looking to replace my 2010 Vintage LG TV but was hoping I could re-use my pre-existing mount as it is attached to a brick fireplace wall.