My sp540v it only prints from one head I replaced new heads I also replaced the print heads board still the same when I switched the print head cables the side didn’t print started working and the side was printing stopped working any suggestions?
When you say new heads, you mean brand new heads correct (not 200.00 alibaba or amazon heads which are not new and cause this type of issue) in my opinion the head that originally didn't work has a short in it and it caused the fuse and or transistor on mainboard blow. I have a video on how to check transistors. Unfortunately, these heads are super sensitive and can be shorted out very easily. Even brand new heads.
There are so many things that can cause them errors. I would start at encoder strip cleaning / replacement. Encoder sensor, inspect bearings for resistance. Gladly help you troubleshoot it
I have a vp300 and recently changed my encoder strip and tried to do the linear encoder. When I start the test it would tell me to remove media. Do you know what I can do to fix it?
I've been having trouble with my SP 540V throwing up the service code 0110. I've replace the encoder strip and sensor. Nowl it throws up the same code but says encoder strip is unusual. I've tried getting into service menu with no luck. This has been going on for about 8 months. It also threw up service code 080. Could it be scan motor?
Hi there .. my head is jamming unpredictably without touching anything and i get the motor error .. i cleaned the encoder but nothing.. did the linear check and it ok . i did a motor ageing and it jamms and fails after going 5 times 5 back and forth.
In order to keep the machine as a vinyl cutter, it needs to think it has ink. Probably best to part machine out and buy a vinyl cutter. The aftermarket bulk cartridges have no way of telling machine the ink is low. Might get you a set of those.
Thak you for your answer, the problem is the bearings of print cariage are broken, are them same as cutter head?Do you have the code of those bearings to order?@@reprint217
I'm thinking you may be referring to a 0110 error code, and It's a problem reading the encoder scale, either from a dirty encoder scale, a damaged encoder scale, or a dirty or damaged encoder reader
My sp540v it only prints from one head I replaced new heads I also replaced the print heads board still the same when I switched the print head cables the side didn’t print started working and the side was printing stopped working any suggestions?
When you say new heads, you mean brand new heads correct (not 200.00 alibaba or amazon heads which are not new and cause this type of issue) in my opinion the head that originally didn't work has a short in it and it caused the fuse and or transistor on mainboard blow. I have a video on how to check transistors. Unfortunately, these heads are super sensitive and can be shorted out very easily. Even brand new heads.
@@reprint217 what is thé price for true printhead for sp540v for exemple ? 490€ ht on Digiprint is ok ?
Change the head fuse it will be a really small white fuse
Hi, I have a Roland SP-300V, I use just for cut can disconnect the ink carriage, there are errors 0110,040,080, Thanks!
There are so many things that can cause them errors. I would start at encoder strip cleaning / replacement. Encoder sensor, inspect bearings for resistance. Gladly help you troubleshoot it
I have a vp300 and recently changed my encoder strip and tried to do the linear encoder. When I start the test it would tell me to remove media. Do you know what I can do to fix it?
You may be having a sensor issue. Sometimes people tape over the rear sensor and machine thinks it has media loaded
Do you know where that sensor would be?
I've been having trouble with my SP 540V throwing up the service code 0110. I've replace the encoder strip and sensor. Nowl it throws up the same code but says encoder strip is unusual. I've tried getting into service menu with no luck. This has been going on for about 8 months. It also threw up service code 080. Could it be scan motor?
It could be scan motor or bearings
Hi, how are you? Do you have any plotter for sale at the moment?
Vinyl cutter or printer?
Hi there .. my head is jamming unpredictably without touching anything and i get the motor error .. i cleaned the encoder but nothing.. did the linear check and it ok . i did a motor ageing and it jamms and fails after going 5 times 5 back and forth.
Definitely sounds like it could be the motor. Try cleaning the rail and applying few drops of 3 in 1 oil
But can i disconect the ink carriage to stop moving? I dont need any more!
In order to keep the machine as a vinyl cutter, it needs to think it has ink. Probably best to part machine out and buy a vinyl cutter. The aftermarket bulk cartridges have no way of telling machine the ink is low. Might get you a set of those.
Also, the ink carriage is vital for setup. You can not remove it or its components. If it were me, I would part it out and buy a vinyl cutter
Thak you for your answer, the problem is the bearings of print cariage are broken, are them same as cutter head?Do you have the code of those bearings to order?@@reprint217
Sire, how i can connect with you?
217-413-2532
My Roland vp-540 is printing shadows or background colors
Try cleaning encoder strip
How to perform this in vs 540
It is typically the same process. You can text me at 217-413-2532 if need guidance
Helo sir please help me coz i have problem with Roland rs 640 error 01010 what is the cause of this error. Thanks alot . Gbu
I'm thinking you may be referring to a 0110 error code, and It's a problem reading the encoder scale, either from a dirty encoder scale, a damaged encoder scale, or a dirty or damaged encoder reader
@@reprint217 no sir the machine error is 0101 sir. The limit position doesn't initialize
@@reprint217 the encoder strip is in good condition
I’m getting a 0010 error when a sheet is done printing and it try to automatically sheet cut but gives me scan motor error 0010
Have you tried changing blade? Sometimes dull blades can cause this
Helo sir please help me i haveproblem with my Roland rs 640have error e001010. Thanks alot sir. Gbu from Saudi Arabia
Run limit initialization
how to do it please help coz i am not expert with this machine roland. thanks@@reprint217
my encoder strip is still in good condition@@reprint217
I take the battery out and it still goes into the cleaning mode and i can't get into the service mode!! So frustrated I want to beat it with a hammer
Will it error out before cleaning finishes?
I have this same problem. My printer will error out during the cleaning process. Scan Motor Error 0010
sp540 has no battery i cant get passed cleaning@@ajnangaj123
@@reprint217 Yes it errors out before the cleaning finishes
Just for cutting
I want to send you a picture but I don’t know how to
217-413-2532
Hello your videos are really helpful, I need to show you some problems I'm having with my Roland machine, please send me your WhatsApp contact
217-413-2532