Thanks for the tips. I cannot believe how little info is out there on a simple adjustment for an old Ford clutch. My pedal is almost on the floor to engage in my Mustang. I am going to check it when I get home. Subscribed!
Thanks for the video man it really helps to have someone on TH-cam that has alot of knowledge on old fords. Long time subscriber and i enjoy all your videos! Helped once again!
Gotta tail light out lol, nice to see another old truck saved, wish I could afford to pick up something older to play with but being a single dad of a 9 year old money don't last long.
Derek Joon the drive off clip is from the day we got it, iv had to track down a few electrical issues from mice and sitting. Everything works currently except for dash lights and the left brake light.
I definitely need to adjust my clutch. It sits so low to the floor and when I try and put it in gear some times it grinds a bit, only in first, second and reverse. I have a T18 so I often skip first gear.
As kids, back in the day, this stuff was automatic for a kid to learn from day one. Basically the old rules were 1 inch of free play in the clutch peddle. That way you stay off the throw out bearing. If you liked less peddle travel you could adjust the linkage for less than an inch of free play. If you liked the clutch near the floor you would increase the free play in the peddle. He's covering this because clutches have been hydraulic for a very long time, and many of you have no clue what he is talking about. Mechanical or cable linkage was the standard until the 1990s rolled around. This is old school tech.
I took my rod out as I’m in a complete rebuild , I loosened the two jam nuts and noticed the rod slides freely. Is it supposed to be threaded inside? I thought it would be but peering inside with a flashlight and no threads.
My beast is a 1996 Bronco 5.0 5speed with 6" lift. When it qualifies for historical tags, I plan on replacing the radius arms and see if that's what causes it to vibrate shaking over 30mph.
I had a 90 bronco for awhile and it wanted to wander pretty bad. I never quite figured it out before we sold it, the tie rods and ball joints weren’t great. I’m sure that played a large part
I actually own a 90 Bronco and when I see vibration in a vehicle at a certain speed I think of a few things. First I check tire balance. Move tires around to see if vibration follows. Next, I check for driveline issues - driveshaft, u joints, pinion angle etc. Bronco's dont have a lot of driveshaft to spare so if its really hanging out of the dustboot slip-joint, I'd certainly get that sorted out before I hit the trails. Perhaps the biggest thing I see with Bronco's is the improper installation of lift kits or just the real "slap it together let's get it on the road" mentality. I hope this helps you.
Nice instructions on doing this...But be careful ,, too much adjustment with the nuts by spreading it out farther and you run the risk of the Large end piece falling off....Especially if driving on rough roads or off roading... I found this out the hard way...By myself In the middle of nowhere,, back before there were Cell phones.... I did manage to get back,, many hours later...only because I was able to put it in gear and creap along... For anyone who is unsure.... This procedure you just showed,, works for both floor shifters and 3 on the tree...because it's clutch adjustment only.... not shift linkage adjustment... Enjoy the Videos...Keepem' coming....
I have the same motor on my 67 mustang. My engagement point is high, but it’s almost uncomfortable to drive because the clutch pedal is almost at my knee. Can I move the height of the pedal so the whole mechanism is closer to the firewall?
It will be out again soon. It’s been a slow process because parts are hard to find. Hopefully starting it up this month. I don’t think there is actually anything left to do but hit the key now
Ok so I have a 75 f100 with an automatic transmission and it wont start in park, I half to slide it between park and reverse to start it and I have the problem of it sliding in reverse when it's in park while it's running. Can someone help me to solve this issue because I can't find any videos on how to fix it.
I wish you could check on a a bar adapter for my bell housing. We just put 302 in a 78 took the 6 cylinder out there is no bracket to mount the ball on the motor
I have a 66 f350 and the clutch engages almost at the floor. I did a couple turns on the linkage and still having trouble with 3rd and 4th gear grinding trying to go into gears. How do I know I have a bad clutch?
Are you talking about the video he did while he was away on a 3 month job or something? If so that was his Galaxy 500. I've never seen a video where he did with a truck. I could be wrong though.
Yeah dude, no one needs to spend all that time necessarily. If your there doing work, great - but no reason that someone has to lay the truck up for awhile to do that if they need to make an adjustment
Hey bud I just got me a 68 Windsor Fairlane with a Toploader 4 speed how do I determine whether this is a close Ratio or wide ratio I think it's a close ratio because first gear is so terrible High you can barely negotiate a parking lot or a speed bump but once you're rolling 25 mile an hour you can rip through the gears like nothing they seem real close I want to put a T5 post 86 so I can have that 335 first gear if I have a close ratio top loader I've got a 220 something first gear you got any ideas for me
@@MattsRageFitGarage another generation of Ford fullsize trucks I rarely see around nowadays are the 1980-86 ones too which came right after those 1973-79 ones.
Ive got a '58 F100 that clutch won't even engage anymore. Used to work okay but grinded in R and 1st. (3 on the tree). Lemme get under there and see what I can see. Will report back when I got something...
Please tell me this works on the brake line as well. My Brakes pedal sags slightly triggering the brake light even with the engine off. I have to use a steering wheel club or rock behind it so it wont engage. AND there is no video on youtube about it. NONE. This is the closest I've gotten for my 69 f100
You just have a weak master cylinder is all. Your pedal resistance is directly correlated to master cylinder opposing force. No other tricks between the two
@@ThunderHead289 Thanks you sir! Big fan of the channel. Your videos are truly an inspiration. So much so I've mustered up the courage to change a fuel line, valve cover gaskets, oil and filter. I even checked for vacuum leaks using propane and a hose today. This coming from someone totally intimated by cars. No BS my friends honestly thought I had a new mechanic named Thunderhead 289 because I learned so much LOL. One asked about headers today. He's getting interested in classic cars now! We grew up in NY in a building with maintenance on staff, none of us can fix anything. Sorry for the long reply, just want you to know your work is making a difference, putting smiles on people's faces, and making guys like myself proud to have fixed even the simplest repair.
@@ThunderHead289 I may have explained it wrong but I just got back from my mechanic, there's a linkage underneath the dashboard He adjusted which fixed it. I wish I could have filmed it but it was definitely not enough room for him and I under there LOL
I bleed FoMoCo Blue....Don't get me wrong,, I have owned other vehicles by the other Manufactures,,, But I always came back to the Blue Oval....And due to the fact that your video's content is FORD related,, I have watched them all...I really enjoy the content and your input / Knowledge as to what your working on....Be it new or old... SOooo, I got to ask.... Did you go to School or Auto Tech, to learn this ?? I never took any Autoshop in school,,, everything I know about working on autos, I learned by doing it myself or watching it be done... alot of trial and error along the way,,, not to mention all the Busted Knuckles and cuts and Bruises...lol Here's a phrase I once heard an Old Mechanic say,,, "Anybody can work on a Chevy, But it takes a REAL Mechanic to work on a FORD".....
so what do you think happened to my 68 mustang clutch? car sits most all year and one day the clutch stopped working. checked it out it looks the same set up as yours. i dont see any broken springs, linkage still all hooked up nothing bent/fall out of place. pedal goes all the way to the floor it wont clutch at all and what ever it is it happened just from sitting not my fault. before that it always worked great. sometime before winter when its not so hot/humid was thinking of pulling the engine/transmission out just to see. 289 with 3 speed
That’s interesting. But doesn’t engage .... 2 things it could be - clutch disk age welded itself to the flywheel. A lot of times if I’m going to leave a carrot a long time, I’ll set the clutch pedal so that the clutch is always pressed in by something. Either that, or the throw out bearing has become dislodged from the fork. You should be able to feel a difference in that though - it wouldn’t feel right. At some point you could simply drop the tranny and inspect. Let me know your thoughts here
i went under the car the fork still has pressure on it because i though it became dislodged from the bell housing pivot. must be something inside i cant see
There are two attachment points, the fork will go onto the bell housing and the throw out bearing with two tabs each. When you say it goes to the floor, does it feel different, like you can’t feel a “catch point” like what I describe in my video?
clutch is always engaged. pedal goes all the way to the floor feels the same with pedal springs still working like before this happened. only way to drive it now is shut engine off, shift into 1st, start engine. car takes off driving soon as the starter starts moving. can take out of gear without clutch
Sounds like the clutch disk welded itself to the flywheel from sitting. Sometimes if you stomp on the clutch pedal really fast a few times while turning it over it will free itself up. This happened on a friends 66 galaxie 4 speed 428. It had sat in a barn for almost a year. Might not be the issue, but if the linkage works right and feels right, I wouldn’t be surprised if it’s the problem
My buddy drove by in his new truck and said he waved and I didn’t wave back, I said you got one of those new trucks and they all look the same, I don’t notice if it’s not vintage. Also, people will move out of the way for you in an old truck, probably they think the brakes don’t work, lol.
Hey Luke, I just dropped in a hopped up 390 into my 67 f100, replaced clutch, TO bearing etc as well. Happy with how it runs etc but while running, won't go into gear. I thought that since it was adjusted for the old worn out clutch that might have been the issue. I adjusted it back out so much so that the clutch pedal feels to disengage about 1/4 of the way up, still won't go into gear while running. I'm not sure what the issue would be, I'm thinking if it's an adjustment issue the clutch would work still, albeit poorly. But it doesn't work at all. Any ideas?
Push in the clutch pedal and turn it over - if it starts, mash the gas pedal a few times to shock load it - obviously don't hit anything and do it in a safe area
@@ThunderHead289came back to your video, my original clutch was seized to the flywheel and actually fell to pieces when I pulled the transmission, watching your video actually helped me figure out that my linkage was also screwed
I need advice (help) lol! I have a 74 f100, I swap motor and T5 ( manual transmission ) from a 90 mustang gt, my problem is that my cable clutch goes through my headers, and after 6months of driving daily it came to the point to where the plastic around the steel cable melted😵, my question is what replacement can I use is there a kit I can buy. Please HELP!
@@ThunderHead289 yes, now I see what you did, but I didn't know u could use the original, so I also swapped the clutch pedal, that is why I used the cable😅 how can I send you pictures of my set up, big fan of your channel, and junkyard digs, 👍!
ThunderHead289 lol. I am 6'4 and you look tall on your vids, and we both have short girlfriend's. Now that is funny. Mine is Japanese. So to see her in my f-250 is really funny. Her getting in is even funniest yet.
Thanks for the tips. I cannot believe how little info is out there on a simple adjustment for an old Ford clutch. My pedal is almost on the floor to engage in my Mustang. I am going to check it when I get home. Subscribed!
Holy mackerel! I was about to buy a new clutch! Thank you SO much. My ‘82 bronco is very grateful. Like night and day.
Just did this to my 73 bronco and the clutch grabs a whole lot better and has more throw. I’ve done a lot to it off this channel thank you!
just got 78 F150 3 on the tree. You described my cluch symptoms to the tee. Did the Z bar tune its golden
Thk you.
Will be upgrading to a T5 soon.
Awesome job, you got that carb. tuned really good! That old beast is purring great!
Literally just fixed my truck dude!! Thank you 🙏 🤣🤣 I thought the transmission finally went bad! It just needed a tightening Wowowow 🤣🤣
What was it doing? Mine stalls when I go into gear and give it gas.
Thanks for the video man it really helps to have someone on TH-cam that has alot of knowledge on old fords. Long time subscriber and i enjoy all your videos! Helped once again!
Thank you that was helpful just bought a 69 Ford F100 it's a sweet one.
Good video man, sweet looking truck and helper..
Gotta tail light out lol, nice to see another old truck saved, wish I could afford to pick up something older to play with but being a single dad of a 9 year old money don't last long.
Derek Joon the drive off clip is from the day we got it, iv had to track down a few electrical issues from mice and sitting. Everything works currently except for dash lights and the left brake light.
thanks for the video, I just bought a 77 f150, really helpful
No problem. That’s what I like to hear, that my efforts were worth it 👍
I am indeed engaging my throw out bearing. That you for the video I have like 1/2 unroll i engage from the top. That you for this video. God bless you
I definitely need to adjust my clutch. It sits so low to the floor and when I try and put it in gear some times it grinds a bit, only in first, second and reverse. I have a T18 so I often skip first gear.
As kids, back in the day, this stuff was automatic for a kid to learn from day one. Basically the old rules were 1 inch of free play in the clutch peddle. That way you stay off the throw out bearing. If you liked less peddle travel you could adjust the linkage for less than an inch of free play. If you liked the clutch near the floor you would increase the free play in the peddle. He's covering this because clutches have been hydraulic for a very long time, and many of you have no clue what he is talking about. Mechanical or cable linkage was the standard until the 1990s rolled around. This is old school tech.
I took my rod out as I’m in a complete rebuild , I loosened the two jam nuts and noticed the rod slides freely. Is it supposed to be threaded inside? I thought it would be but peering inside with a flashlight and no threads.
Worked for me today on my 69 Bronco!
My beast is a 1996 Bronco 5.0 5speed with 6" lift. When it qualifies for historical tags, I plan on replacing the radius arms and see if that's what causes it to vibrate shaking over 30mph.
I had a 90 bronco for awhile and it wanted to wander pretty bad.
I never quite figured it out before we sold it, the tie rods and ball joints weren’t great. I’m sure that played a large part
I actually own a 90 Bronco and when I see vibration in a vehicle at a certain speed I think of a few things. First I check tire balance. Move tires around to see if vibration follows. Next, I check for driveline issues - driveshaft, u joints, pinion angle etc. Bronco's dont have a lot of driveshaft to spare so if its really hanging out of the dustboot slip-joint, I'd certainly get that sorted out before I hit the trails. Perhaps the biggest thing I see with Bronco's is the improper installation of lift kits or just the real "slap it together let's get it on the road" mentality. I hope this helps you.
Nice instructions on doing this...But be careful ,, too much adjustment with the nuts by spreading it out farther and you run the risk of the Large end piece falling off....Especially if driving on rough roads or off roading...
I found this out the hard way...By myself In the middle of nowhere,, back before there were Cell phones.... I did manage to get back,, many hours later...only because I was able to put it in gear and creap along...
For anyone who is unsure.... This procedure you just showed,, works for both floor shifters and 3 on the tree...because it's clutch adjustment only.... not shift linkage adjustment...
Enjoy the Videos...Keepem' coming....
Very true. I actually lost one on my original f100. It has a custom made piece that is extra long because of this
I have the rod zip tied to the z bar just in case it falls off for that very reason.
I have the same motor on my 67 mustang. My engagement point is high, but it’s almost uncomfortable to drive because the clutch pedal is almost at my knee. Can I move the height of the pedal so the whole mechanism is closer to the firewall?
Where is that militaryJeep that you found two months back I've been waiting to see more progress on it just curious
It will be out again soon.
It’s been a slow process because parts are hard to find. Hopefully starting it up this month. I don’t think there is actually anything left to do but hit the key now
where is the 65' ford f250? for that car i subbed!
I was looking for something on the 1964 F250 on the clutch adjustment.
Love these trucks!
I have a 1973 FORD ECONOLINE VAN. 3 on the tree the is stuck in 1st but its not really in the 1st gear position. Any tips?
Ok so I have a 75 f100 with an automatic transmission and it wont start in park, I half to slide it between park and reverse to start it and I have the problem of it sliding in reverse when it's in park while it's running. Can someone help me to solve this issue because I can't find any videos on how to fix it.
I wish you could check on a a bar adapter for my bell housing. We just put 302 in a 78 took the 6 cylinder out there is no bracket to mount the ball on the motor
F600 owner says thanks!
I have a 66 f350 and the clutch engages almost at the floor. I did a couple turns on the linkage and still having trouble with 3rd and 4th gear grinding trying to go into gears. How do I know I have a bad clutch?
I know this is an older video but are you running a return line to the gas tank like you did in another video?
I had actually just bought this truck the very day of this video I think
Are you talking about the video he did while he was away on a 3 month job or something? If so that was his Galaxy 500. I've never seen a video where he did with a truck. I could be wrong though.
I have a 1979 F150 4X4 and have rebuilt the linkage with new bushings from LMC. That should be done before you make adjustments.
Yeah dude, no one needs to spend all that time necessarily. If your there doing work, great - but no reason that someone has to lay the truck up for awhile to do that if they need to make an adjustment
Love Ford Blue!
I have the same truck. In 4x4 (I use it as a plow truck), I noticed the rear wheels will spin, but the front kinda engages????
Hey bud I just got me a 68 Windsor Fairlane with a Toploader 4 speed how do I determine whether this is a close Ratio or wide ratio I think it's a close ratio because first gear is so terrible High you can barely negotiate a parking lot or a speed bump but once you're rolling 25 mile an hour you can rip through the gears like nothing they seem real close I want to put a T5 post 86 so I can have that 335 first gear if I have a close ratio top loader I've got a 220 something first gear you got any ideas for me
Im here for the social experiments......... ooops wrong channel. Nice truck man
I might have to revive that channel. We will see for sure
How sloppy floppy is your stick?
I just got my 77 F250 and it looks like your stick is as loose n flop around as mine
That generation Ford fullsize pickups are super rare nowadays.
They are? I see them all over the place on the west coast. Especially once you get out of the city, they're friggin everywhere.
@@MattsRageFitGarage o wow.
@@MattsRageFitGarage another generation of Ford fullsize trucks I rarely see around nowadays are the 1980-86 ones too which came right after those 1973-79 ones.
@@kevinrichards3288 theres tons of 80-86 and newer here as well. I see several on the road every day.
@@MattsRageFitGarage I do see a lot of the 87-91 & 92-96 generation Ford F-series pickups around tho.
Ive got a '58 F100 that clutch won't even engage anymore. Used to work okay but grinded in R and 1st. (3 on the tree). Lemme get under there and see what I can see. Will report back when I got something...
Just by watching this, I think where part of my problem started.
Isn't this the truck in the "Emily's truck" video you just posted 4 hours ago showing you bringing it home?
Please tell me this works on the brake line as well. My Brakes pedal sags slightly triggering the brake light even with the engine off. I have to use a steering wheel club or rock behind it so it wont engage. AND there is no video on youtube about it. NONE. This is the closest I've gotten for my 69 f100
You just have a weak master cylinder is all. Your pedal resistance is directly correlated to master cylinder opposing force. No other tricks between the two
@@ThunderHead289 Thanks you sir! Big fan of the channel. Your videos are truly an inspiration. So much so I've mustered up the courage to change a fuel line, valve cover gaskets, oil and filter. I even checked for vacuum leaks using propane and a hose today. This coming from someone totally intimated by cars. No BS my friends honestly thought I had a new mechanic named Thunderhead 289 because I learned so much LOL. One asked about headers today. He's getting interested in classic cars now! We grew up in NY in a building with maintenance on staff, none of us can fix anything. Sorry for the long reply, just want you to know your work is making a difference, putting smiles on people's faces, and making guys like myself proud to have fixed even the simplest repair.
@@ThunderHead289 I may have explained it wrong but I just got back from my mechanic, there's a linkage underneath the dashboard He adjusted which fixed it. I wish I could have filmed it but it was definitely not enough room for him and I under there LOL
I bleed FoMoCo Blue....Don't get me wrong,, I have owned other vehicles by the other Manufactures,,, But I always came back to the Blue Oval....And due to the fact that your video's content is FORD related,, I have watched them all...I really enjoy the content and your input / Knowledge as to what your working on....Be it new or old...
SOooo, I got to ask.... Did you go to School or Auto Tech, to learn this ??
I never took any Autoshop in school,,, everything I know about working on autos, I learned by doing it myself or watching it be done... alot of trial and error along the way,,, not to mention all the Busted Knuckles and cuts and Bruises...lol
Here's a phrase I once heard an Old Mechanic say,,,
"Anybody can work on a Chevy, But it takes a REAL Mechanic to work on a FORD".....
so what do you think happened to my 68 mustang clutch? car sits most all year and one day the clutch stopped working. checked it out it looks the same set up as yours. i dont see any broken springs, linkage still all hooked up nothing bent/fall out of place. pedal goes all the way to the floor it wont clutch at all and what ever it is it happened just from sitting not my fault. before that it always worked great. sometime before winter when its not so hot/humid was thinking of pulling the engine/transmission out just to see. 289 with 3 speed
That’s interesting. But doesn’t engage ....
2 things it could be - clutch disk age welded itself to the flywheel. A lot of times if I’m going to leave a carrot a long time, I’ll set the clutch pedal so that the clutch is always pressed in by something. Either that, or the throw out bearing has become dislodged from the fork. You should be able to feel a difference in that though - it wouldn’t feel right.
At some point you could simply drop the tranny and inspect.
Let me know your thoughts here
i went under the car the fork still has pressure on it because i though it became dislodged from the bell housing pivot. must be something inside i cant see
There are two attachment points, the fork will go onto the bell housing and the throw out bearing with two tabs each.
When you say it goes to the floor, does it feel different, like you can’t feel a “catch point” like what I describe in my video?
clutch is always engaged. pedal goes all the way to the floor feels the same with pedal springs still working like before this happened. only way to drive it now is shut engine off, shift into 1st, start engine. car takes off driving soon as the starter starts moving. can take out of gear without clutch
Sounds like the clutch disk welded itself to the flywheel from sitting. Sometimes if you stomp on the clutch pedal really fast a few times while turning it over it will free itself up.
This happened on a friends 66 galaxie 4 speed 428.
It had sat in a barn for almost a year.
Might not be the issue, but if the linkage works right and feels right, I wouldn’t be surprised if it’s the problem
My buddy drove by in his new truck and said he waved and I didn’t wave back, I said you got one of those new trucks and they all look the same, I don’t notice if it’s not vintage. Also, people will move out of the way for you in an old truck, probably they think the brakes don’t work, lol.
Hey Luke, I just dropped in a hopped up 390 into my 67 f100, replaced clutch, TO bearing etc as well. Happy with how it runs etc but while running, won't go into gear. I thought that since it was adjusted for the old worn out clutch that might have been the issue. I adjusted it back out so much so that the clutch pedal feels to disengage about 1/4 of the way up, still won't go into gear while running. I'm not sure what the issue would be, I'm thinking if it's an adjustment issue the clutch would work still, albeit poorly. But it doesn't work at all. Any ideas?
Sounds like a backwards clutch disk
Good info. Thank you much.👍
Can't have too much pedal travel after disengagement or you'll take the pressure plate over center too far.
Think I'd go with a hydraulic setup when I replaced the clutch.
How would one go about getting a clutch unstuck in an 82 bronco with a 3speed od and 302 v8
Push in the clutch pedal and turn it over - if it starts, mash the gas pedal a few times to shock load it - obviously don't hit anything and do it in a safe area
@@ThunderHead289came back to your video, my original clutch was seized to the flywheel and actually fell to pieces when I pulled the transmission, watching your video actually helped me figure out that my linkage was also screwed
I need advice (help) lol! I have a 74 f100, I swap motor and T5 ( manual transmission ) from a 90 mustang gt, my problem is that my cable clutch goes through my headers, and after 6months of driving daily it came to the point to where the plastic around the steel cable melted😵, my question is what replacement can I use is there a kit I can buy. Please HELP!
Why are you using the cable is my first question.
I used the old mechanical clutch setup - it’s absolutely immortal comparatively
@@ThunderHead289 yes, now I see what you did, but I didn't know u could use the original, so I also swapped the clutch pedal, that is why I used the cable😅 how can I send you pictures of my set up, big fan of your channel, and junkyard digs, 👍!
For the clutch z bar
Can you do this on a 95 f150?
No. It has a hydraulic clutch slave cylinder that's self adjusting so if your clutch is slipping it is probably worn out and needs replacing.
@@kraigcochran9995 thank you
For motorcycles we call that the friction zone.
Thank you..WoW...
What part of iowa are you from?
Central Iowa. Close to Ames
@@ThunderHead289 hey I live by Sioux city and I just got a 73 f100 4wd with 360, 4 speed, thinking about doing your 390 conversion.
The girlfriend is going to claim that truck I bet. Lol
That has actually already happened
ThunderHead289 lmao. My girlfriend just claimed my f-250 super duty. The funny part is she is all of 4'9.
Mines 5 foot 4 😂
ThunderHead289 lol. I am 6'4 and you look tall on your vids, and we both have short girlfriend's. Now that is funny. Mine is Japanese. So to see her in my f-250 is really funny. Her getting in is even funniest yet.
Send it.
Not gonna pass the visor test.
I see that used to be an automatic from the factory
It's always been a standard 4 speed.
They are all mechanical clutches. I have the 1964 F250 and it looks similar.