So i fitted 2 map sensors after getting the engine red fault on screen and poor sub 4k running and stalling when setting off. I bought 2 cheap ones off amazon. After taking fairing of i decided that it wasnt worth the effort to just change 1. Also after taking the fiddley bolts out i fastened them back in place with a cable tie. They don't warrent a bolt with nylock nut. I also stuck the penny washer in place with some gaffer tape and poked a hole through for the screw. This screw which is in the top corner below the headlight on the inside of the fairing screws into a rubber wellnut that expands. Like the type used on fairing windscreens. Note. For the map sensor at front of bike i used a hex bit and 1/4 " spanner to get in, or you could cut down a allenkey. Anyways, one i changed the map sensors my bike was free from the red engine warning banner displayed on screen, and ran perfectly again below 4k.
Grate video mate. Could you please give me you feedback regarding those map sensors you installed regarding performance and quality? Did you fill any diference compered to the original ones?
Hey there! Install the sensors today on my panigale 1299s. I decided to replace both of them although just one was faulty. The engine light immediately disappeared. The bike is running perfectly. No diference noticed competed to the original ones. Thank you very much once again.
Hi hope you are doing great. How is Germban map sensor working rightnow? Are they still working fine because I am also thinking to buy these will be very helpful for me with your review.
A quick warning if your planing to take your bike to a shop DO NOT DO THIS TEST because when you pull the map sensor plugs the ecu is going to send a map sensor failure code and than the shop is going to charge you for both map sensors
So i fitted 2 map sensors after getting the engine red fault on screen and poor sub 4k running and stalling when setting off. I bought 2 cheap ones off amazon. After taking fairing of i decided that it wasnt worth the effort to just change 1. Also after taking the fiddley bolts out i fastened them back in place with a cable tie. They don't warrent a bolt with nylock nut. I also stuck the penny washer in place with some gaffer tape and poked a hole through for the screw. This screw which is in the top corner below the headlight on the inside of the fairing screws into a rubber wellnut that expands. Like the type used on fairing windscreens. Note. For the map sensor at front of bike i used a hex bit and 1/4 " spanner to get in, or you could cut down a allenkey. Anyways, one i changed the map sensors my bike was free from the red engine warning banner displayed on screen, and ran perfectly again below 4k.
Hey Mate,
Really appreciate this video!
Cheers
Grate video mate.
Could you please give me you feedback regarding those map sensors you installed regarding performance and quality?
Did you fill any diference compered to the original ones?
@@Desmotube100 worked great and really smoothed the throttle response out. Give it a few miles to adjust to the new sensors. Worth every penny.
@@reddoggarageThanks for your fast reply!!!
It's so good to hear that. I'm going to order right now.
Thanks once again!!!
Hey there! Install the sensors today on my panigale 1299s. I decided to replace both of them although just one was faulty. The engine light immediately disappeared. The bike is running perfectly. No diference noticed competed to the original ones. Thank you very much once again.
@@Desmotube100 glad it helped!
@@reddoggarage a lot!!!
Hi hope you are doing great. How is Germban map sensor working rightnow? Are they still working fine because I am also thinking to buy these will be very helpful for me with your review.
A quick warning if your planing to take your bike to a shop DO NOT DO THIS TEST because when you pull the map sensor plugs the ecu is going to send a map sensor failure code and than the shop is going to charge you for both map sensors
But if you've stripped your bike to get to the map, you'd be well advised to change in any case
Did the sensors last ok?
@@gattoflyer yea no issues so far
I wonder howuch Ducati would of charged for that swap.
Any update on the Racing Mower?
Next video will be coming out soon!
Can't wait! I really plan on doing that type of building one day.. @@reddoggarage
Sensor air?
Manifold Air Pressure