Thank you!! I had my 10/22 air rifle less than a day before it jammed. Umarex was useless. As soon as I took the barrel off I was able to clear the jam.
wow , i already have a couple newer versions of the crosman 1077 . i have had a couple older ones in the past also . i have one modded and one stock for fun now . my modded one gets about 25 to 28 shots and the stock one about 60 per 12 gram co2 ! . i been thinking on this a while , could have gotten one half off a year or two , i like it and see where i could def mod it . the hammer could be made stronger to hit harder , a lighter valve spring , take restrictor out and drill those 3 holes . thank you for this video my friend !!! i enjoyed it !!!
Do not do this!!! Companies like Umarex spend loads of time and money designing and engering quality products like this. I tried this mod removing the small meetering valve, and what a waste if time. The gun fired about 4 weak shots (very loudly) and then ran out of air on the fifth only pushing out the pellet enough to get stuck not allowing the mag to release. Had to dissamble, reinstall valve and all is back to normal, if you need a stronger gun buy a stronger gun!!!
So I decided to make a video to prove that my mod works since some people are saying that it doesn't work. Watch my new video and I guarantee you will see what you did wrong.
removal of the "restrictor" resulted in a loss of seal in the valve... causing a massive leak every time the gun was fired, barely able to spit the pellets out of the gun... I did however come up with a simple way to increase the hammer spring pressure, resulting in more power ( along with a super stiff first stage of the trigger) .You can also dig out the rubber pad that is embedded in the hammer, and replace it with a steel pin, preferably one that sits a mm or two proud of the hammer surface...
So I decided to make a video to prove that my mod works since some people are saying that it doesn't work. Watch my new video and I guarantee you will see what you did wrong.
I seriously wanna put my Umarex Ruger 10/22 into a new body, like the Magpul Hunter Stock, but it’s tough because of the C02 containment system in the back buttstock.
So I decided to make a video to prove that my mod works since some people are saying that it doesn't work. Watch my new video and I guarantee you will see what you did wrong.
Mine has a slow leak . Shoots fine, but it's completely empty if i leave it sitting overnight. Any tips on where it could be leaking? Would it be a good idea to tear it down to a certain point, and then spray it with soapy water to see if bubbles show up where it might be leaking? Great video detailing how to disassemble. Never thought about trying to increase power. Trying to figure out how to fix the leak is what brought me here. I got it to shoot at varmints that keep killing my chickens at night. I didn't want a real gun. Thoughts?
Thank you for the comment. I'm not sure why for some people it leaks but if you watch my other video you can see me do the mod again and show that it doesn't leak. I think the problem might be the small o ring that goes on the tube you have to make sure to put it on correctly.
Papi781 - thank you for video. The tube / chamber on my gun that holds the air cartridges is a little loose. It moves a bit when you put a small amount of pressure on it such as when tightening up the new cartridges. That results in the compressed air venting into the mechanism and all air is lost. Your video shows a small O ring sealing the mechanism end of the brass tube. Is there a similar O ring on the tube / chamber end of the brass tube ? could that O ring be the problem do you think ? Cheers from New Zealand and well done on the video
That's a good question. I don't remember if there was a small o ring on that end of the tube but that could very well be a possibilty. I don't think I tinkered with that end of the brass tube so that's probably why I don't remember but I would definitely go in there and check it out. It's fairly easy to disassemble the 10/20 I hope you figure out your problem. Good luck!
The Airgun Detectives channel suggests placing a dime between the 2 CO2 cartridges to take up any slack....this also ensures the piercing of both CO2 cartridges. [ th-cam.com/video/9Ju6icGoT4A/w-d-xo.html ]
@@valdivia1234567 Hi Craig, I took rifle back to retailer who returned it to New Zealand import agent. They replaced the rifle with a new one - I did not hear anything from them re the problem, whether it could be fixed or otherwise. I think the repair by a gunsmith would be likely to cost the agent more than simply replacing faulty rifle with the new one.
Hi sorry for such a late response. That might not work since the restrictor is not fixed in place it would probably just spin with the drill bit but you can try it.
Removing the little brass restrictor allows more CO2 to continually dump into the valve at the moment the hammer hits the valve and the gas is released into the chamber. The little brass restrictor is there to prevent CO2 to keep dumping into the valve so that it doesn't waste too fast. Yes this will give your shots more power but the downside is that you will get way less shots per CO2 cartridge. Why don't you try it and you'll see the difference. You will hear how much louder the gun sounds when you shoot it. You can always just reinstall the little restrictor if you don't like it afterwards.
So I decided to make a video to prove that my mod works since some people are saying that it doesn't work. Watch my new video and I guarantee you will see what you did wrong.
Thank u for taking time to walk us thru the internals of this lil great plinker. It's very few videos depicting the internals so I subbed straight away out of respect
You have to make sure you look at the pins when you take them out, they can be any way round. Just tap out far enough to see which end is which, you need to see a knurled bit on the end, if it is, tap out from the other, plain, end.
DONT LISTEN TO THIS DUDE I just watched his video and removed the valve limiter and the consequence is the co2 pressure is too much for the upper valve and I got a not stop steady leak and can't store it with co2 for the road
So I decided to make a video to prove that my mod works since some people are saying that it doesn't work. Watch my new video and I guarantee you will see what you did wrong.
Thank you!! I had my 10/22 air rifle less than a day before it jammed. Umarex was useless. As soon as I took the barrel off I was able to clear the jam.
wow , i already have a couple newer versions of the crosman 1077 . i have had a couple older ones in the past also . i have one modded and one stock for fun now . my modded one gets about 25 to 28 shots and the stock one about 60 per 12 gram co2 ! . i been thinking on this a while , could have gotten one half off a year or two , i like it and see where i could def mod it . the hammer could be made stronger to hit harder , a lighter valve spring , take restrictor out and drill those 3 holes .
thank you for this video my friend !!! i enjoyed it !!!
Thanks for the comment
Just finished a trigger mod using your videos. The trigger pull dropped from the factory 10lbs to approx.5lbs. Could not have done without your help.
@@dorecannon9640 That's great man. How did you do it?
prima Video , DANKE , sehr gut und anschaulich gemacht , perfekt zum Nachbau !!
Do not do this!!! Companies like Umarex spend loads of time and money designing and engering quality products like this. I tried this mod removing the small meetering valve, and what a waste if time. The gun fired about 4 weak shots (very loudly) and then ran out of air on the fifth only pushing out the pellet enough to get stuck not allowing the mag to release. Had to dissamble, reinstall valve and all is back to normal, if you need a stronger gun buy a stronger gun!!!
shut up pls and thanks
So I decided to make a video to prove that my mod works since some people are saying that it doesn't work. Watch my new video and I guarantee you will see what you did wrong.
Thank you so much for the step by step instructional video. Very well done my friend.
You are very welcome
Awesome video, thank you.
removal of the "restrictor" resulted in a loss of seal in the valve... causing a massive leak every time the gun was fired, barely able to spit the pellets out of the gun... I did however come up with a simple way to increase the hammer spring pressure, resulting in more power ( along with a super stiff first stage of the trigger) .You can also dig out the rubber pad that is embedded in the hammer, and replace it with a steel pin, preferably one that sits a mm or two proud of the hammer surface...
Sounds like I’m much better off just leaving it stock and not touching it at all, thanks!
So I decided to make a video to prove that my mod works since some people are saying that it doesn't work. Watch my new video and I guarantee you will see what you did wrong.
Thanks for this video, the disassembly was just what I needed!
I seriously wanna put my Umarex Ruger 10/22 into a new body, like the Magpul Hunter Stock, but it’s tough because of the C02 containment system in the back buttstock.
thank you. been waiting for a year. UK. simpler than I thought. if you tinker with others how about trying to make the trigger lighter.
Made my gun bounce of plywood removing that little valve lol
Really like bounce off the wood?
Lol!!! Maybe the wood was made of rubber or jello
So I decided to make a video to prove that my mod works since some people are saying that it doesn't work. Watch my new video and I guarantee you will see what you did wrong.
Mine has a slow leak . Shoots fine, but it's completely empty if i leave it sitting overnight. Any tips on where it could be leaking? Would it be a good idea to tear it down to a certain point, and then spray it with soapy water to see if bubbles show up where it might be leaking? Great video detailing how to disassemble. Never thought about trying to increase power. Trying to figure out how to fix the leak is what brought me here. I got it to shoot at varmints that keep killing my chickens at night. I didn't want a real gun. Thoughts?
Great video, my gun as soon as you load the C02 it leaks out in the receiver area. Any ideas?
Thank you for the comment. I'm not sure why for some people it leaks but if you watch my other video you can see me do the mod again and show that it doesn't leak. I think the problem might be the small o ring that goes on the tube you have to make sure to put it on correctly.
Good video, I would have like to see a crono of the the mods though
Yeah me too. I just don't have one at the moment but if I were to guess maybe 50 - 80 extra fps. 🤷
Papi781 - thank you for video. The tube / chamber on my gun that holds the air cartridges is a little loose. It moves a bit when you put a small amount of pressure on it such as when tightening up the new cartridges. That results in the compressed air venting into the mechanism and all air is lost. Your video shows a small O ring sealing the mechanism end of the brass tube. Is there a similar O ring on the tube / chamber end of the brass tube ? could that O ring be the problem do you think ?
Cheers from New Zealand and well done on the video
That's a good question. I don't remember if there was a small o ring on that end of the tube but that could very well be a possibilty. I don't think I tinkered with that end of the brass tube so that's probably why I don't remember but I would definitely go in there and check it out. It's fairly easy to disassemble the 10/20 I hope you figure out your problem. Good luck!
The Airgun Detectives channel suggests placing a dime between the 2 CO2 cartridges to take up any slack....this also ensures the piercing of both CO2 cartridges. [ th-cam.com/video/9Ju6icGoT4A/w-d-xo.html ]
Did you figure out your problem? I'm also having the problem of having all my CO2 empty when tightening up new cartridges.
@@valdivia1234567 Hi Craig, I took rifle back to retailer who returned it to New Zealand import agent. They replaced the rifle with a new one - I did not hear anything from them re the problem, whether it could be fixed or otherwise. I think the repair by a gunsmith would be likely to cost the agent more than simply replacing faulty rifle with the new one.
Watch my new video. You'll see what went wrong
Is it possible to drill the restrainer without remouving it? Thanks for the video!
Hi sorry for such a late response. That might not work since the restrictor is not fixed in place it would probably just spin with the drill bit but you can try it.
How many fps or foot pounds does this mod give the gun?
I have an issue with loosing air when I install my CO2 cylinder. Do you know what causes that. I screw it in and I hear it leaking until it's empty.
I don't know. Maybe you can take it apart and put in the CO2 cartridge while it's disassembled then you might be able to see where your problem is.
@@timr617 thanks. Great idea!
Can we convert this to pcp air rifle with more fps
I'm sure with a little mechanical aptitude it should be possible. That would be awesome make sure to post a video if you do it. 👍
I doubt you got any measurable improvement pulling that brass piece. The limiting factor here is the lower pressure of CO2vs charged air.
Removing the little brass restrictor allows more CO2 to continually dump into the valve at the moment the hammer hits the valve and the gas is released into the chamber. The little brass restrictor is there to prevent CO2 to keep dumping into the valve so that it doesn't waste too fast. Yes this will give your shots more power but the downside is that you will get way less shots per CO2 cartridge. Why don't you try it and you'll see the difference. You will hear how much louder the gun sounds when you shoot it. You can always just reinstall the little restrictor if you don't like it afterwards.
So I decided to make a video to prove that my mod works since some people are saying that it doesn't work. Watch my new video and I guarantee you will see what you did wrong.
Moral to the story...Don't purchase Ruger 10/22 rifles; there crap!
@@dwightjulien5845 Actually they're pretty good.
What would be the result in terms of added ft/lbs of energy? Also, how would it affect the amount of shots per two cartridges of co2?
Great video. Thanks a lot.
Thank u for taking time to walk us thru the internals of this lil great plinker. It's very few videos depicting the internals so I subbed straight away out of respect
Thank you for such a detailed disassembly! Excellent! I want to try to work on the stiff DA trigger!
You have to make sure you look at the pins when you take them out, they can be any way round. Just tap out far enough to see which end is which, you need to see a knurled bit on the end, if it is, tap out from the other, plain, end.
Thanks for the tip 👍
How do I know if I've got the 450FPS model or the 700 FPS ?
DONT LISTEN TO THIS DUDE I just watched his video and removed the valve limiter and the consequence is the co2 pressure is too much for the upper valve and I got a not stop steady leak and can't store it with co2 for the road
Well mine was working fine after the mod I didn't have any leaks at all so maybe you did something different.
@@timr617 Did you have a umarex Colt SAA , Did you think we can get more FPS out of theses ?
So I decided to make a video to prove that my mod works since some people are saying that it doesn't work. Watch my new video and I guarantee you will see what you did wrong.
Still over all a good how to video, thanks for your time
thanx for the foundation of disassembly.. my trigger return sticks. now i feel ok attempting the repair. no need to reply.
Can we modify this gun with wooden buttstock
Your face is showing😐
Lol I know😂
Lol ok
Classic example of taking it apart - no idea how to put back together
huh? he has a video showing how to put back together.