Mazda remote keyless entry key DIY programming, keyfob only (DOORS ONLY)
ฝัง
- เผยแพร่เมื่อ 16 พ.ย. 2012
- Visit us at www.carandtruckremotes.com/
Do it yourself Mazda keyless entry remote programming. Works for most Mazda remotes. One working key is required for programming.
THIS WILL NOT WORK FOR THE SMART KEY SYSTEM
NOTE: A maximum of 3 key remote transmitters can be programmed.
Obtain all key remote transmitters.
NOTE: Any existing key remote transmitters not used during programming will become inoperative.
Remove key from ignition switch.
Close all doors.
Open driver's door.
Carry out the following procedure within 24 seconds:
Turn ignition switch ON and back to LOCK position 3 times.
Press and release driver's door courtesy light switch 3 times.
Ensure doors lock and unlock.
If not, wait 40 seconds and repeat procedure starting with driver's door already open.
Press UNLOCK button of each key remote transmitter twice.
Ensure doors lock and unlock after each operation.
If not, proceed as follows:
Press and release driver's door courtesy light switch once.
Ensure doors lock and unlock twice.
Repeat procedure starting with driver's door already open. - ยานยนต์และพาหนะ
![ภาพนี้ก็ฮาเหมือนกันนะเนี้ย #2 SS8 [ พากย์นรก MEME.EXE ] | easy boy](http://i.ytimg.com/vi/RMhUgxxD49Q/mqdefault.jpg)
2011 Mazda 2. Seven years ago my daughter lost the key and we had to use the spare. I found it a year later down the back of the couch. The buttons no longer worked. FOR SIX YEARS I have been manually locking and unlocking the car. SIX YEARS! I have no idea why this video came up in my feed at 1am as I was going to bed. But I just tried it and it works!!! Thank you!!!!
This works!! It took a few moments to cycle through, but after that I am back in business! Thank you so much for saving me time and money!
Just wanted to say a BIG THANK YOU! Your instructions worked perfectly, even though my Mazda is a right hand drive! I'd seen previous instructions about turning the light on and off three times - total twaddle.
I'd just replaced my battery and was very peed off that it wouldn't work. I watched your video once, and 'hey presto' - spot on. Thanks again, you've saved me £££'s. If anyone wants to know I have a 2002 Mazda Premacy Gxi 1.8 litre. Thank you sweetcheeks, I'm thrilled :-D
WOW! worked perfectly. Even the locksmith couldn't do it with his fancy gadgets, but this worked. I'm STOKED! Thanks (2010 mazda 6)
Thank you so much! This totally solved my problem where both my remotes stopped working! The people I talked to all said I should change the battery. After paying $5 to change one, nothing happened so I found your video when I googled the problem, did the steps at the same time as you, and it worked!!
Thank u man! Works like a charm on my 2012 Mazda 2 and also starts working third button for trunk release that i've never had before! Thank you!
Im about to buy a 2012 Mazda 2. Thanks for verifying!
Thanks for this video; it worked and now my wife loves me again! I tried a few times and the last time I skipped the 'lock and unlock door' step and went to the 'press the unlock on the remote twice' and it reprogrammed that time.
Thanks for you help. I'm in Western Australia and your TH-cam video just worked for my son's 2009 Mazda 3 hatch in Nov 2020. Love it.
I used it on a PK 2011 Ford Ranger with a Key Fob in Australia. Meaning right hand drive. Worked perfectly first time. Thanks for posting the video.
It works on my 2007 Mazda 3. Thank you! Just bought a used key fob from eBay and programmed it using this technique. Now I just need to get it cut and program the chip at the locksmiths :)
Hi, I'm really struggling with the same car as yours, please help
7:49 PM, 6/21/2021 - just programmed a fob for my Protege5, with the help of this video. Thank you!
Thank you!!!!!!!!! I just programmed my remote by following your directions 😀
It worked like a charm on my 2003 Mazda Protege5! Thank you very much. It was the second time I had to reprogram the remote key. The first time I went to a Mazda dealer and the key was reprogrammed at no charge, but it's much more convenient (and empowering!) to be able to do it myself! Thanks again.
Michel Bruyère did your Mazda keyless entry stopped working and you reprogrammed it? Or did you buy a new key and programmed that one? Please help!
Wow it actually worked on my 2006 mazda 3. Took 3 tries but finally synced. Thanks
I have a mazda 3 2006 which has issues with the remote. Can you plz recommend me where i can buy a replacement remote from?
You're a genius, It was so simple to reprogram my Madza Protégé 5. I followed instructions to the letter and figured it out on the first attempt. You have no idea how much your video helped. I saved myself 100.00 dollars or more programming my own vehicle. Again, thanks alot.
Many thanks for this video, it was annoying me that I couldn't get my central locking to work after changing the battery in the fob but this video showed me where I was going wrong 👍
Worked great on my 2008 mazda 3. Was not a smart remote key, but never came with keyfobs. So an aftermarket keyfob and this video gave me keyless entry after owning the car for several years not having it.
Thank you so much bru, my key just stopped working after i removed the battery, tried ur instructions and it worked instantly.
Lost of words but thank you so much appreciate it
I bought yesterday two new keyfob remote control. I will try programming them next week. Hope this steps will work.
That is correct. The "switchblade" key is only available for 2010 on the Mazda 3 model. The 2004 Mazda 3 has a separate key and remote as shown on our website; however, the programming procedure is the same for the remote whether it is separate or switchblade.
Thanks heaps! Struggled to find the right thing to do for my KQ Ford Laser. This worked a treat! (Mazda 323/ Ford Laser are very similar). Legend!
Worked great on my uk spec Mazda 3. Thanks for the info and an easy to follow video.
thank you for showing this. works a treat.
Thank you - followed your instructions and it worked spot on. I have noted that some other instructions say to remove the key from the ignition after turning the ignition on and off three times however this did not work for me. Leaving the key in the ignition as per your instructions worked. Thanks again and all the best - Cheers.
Perfect! Worked like a charm for my 2008 Mazda 5. Thank you for posting your video.
@David Gorris Mine wasn't a new key/keyfob ... my old one just stopped working for the door locks. Once I replaced the battery I had to go through the procedure noted in the video to get the keyfob synched to the car again. It's been a LONG while since I needed a key/keyfob for a vehicle. Last one was for a Ford more than 10 years ago. I did have to get that done at the dealer and it cost about $75, but I'm sure prices have changed since then.
thank you so much, I just went to a Mazda dealer and they only take my money, because I buy the remote control in eBay and not with them, but now I did program my remote control by my self .
Thanks for this instructional video. Worked first time reprogramming my remote for a Mazda 323 ba Astina hardtop.
This worked for me. Thank you for sharing.
2008 Mazda 6, 2 years thinking the fob didn’t work for me. THIS PROGRAMMING WORKED FOR ME!!
Thanks heaps! I did it on my 2005 Mazda 3 and it worked. I would only add that I first needed to start the car with the door closed, then turn off the engine, open the door and follow the rest. I also left the key in the ignition. Crazy but brilliant!
Thanks a lot! I was able to program one of my mazda 3's key fob to work on my mazda 6. AMAZING
OMG! You saved me $225!!!!! Thank you!
I can confirm this works with Mazda DEMIO on a fob model No 41601.
Really great! Thanks a lot.
Just programed a second remote. Thank you very much!
2009 MX5 - it worked for me - thank you
Thank you very much sir for this lovely video . I got my new remote working just following the steps you showed in this video.
Just worked!! Thank you so much!
Thank you so much for making this video I almost payed 300$ to program my vehicle and your steps actually work.
If anyone is having trouble getting their Mazda 3 into programming mode like I was at first, I discovered that, at least for my car, I had to additionally manually press lock/unlock on the driver's side door at the beginning after you open the door but before the key cycling. Every thing else as explained in this video worked great. Thanks!
Daniel MacDonald Some cars are a little quirky and require a few tweaks to the programming process. Glad to hear you got it working :)
My car wouldn't go into programming mode. I had to push my key inwards and hold it inwards the whole time to make sure it knew my key was in the ignition. After I did that it worked flawlessly. I've been trying to figure this out for years.
BumperPlates dude you're a life saver. After I held my key in, it finally works. Thank you veryone for the tips.
HOLDING THE KEY IN THE ENTIRE TIME FOR MAZDA 3 - THANK YOU 🙏🏻
Yes, you simply have to push the button on each other remote before exiting the programming mode. You can have up to 4 working remotes.
Thank you so much! great video, very helpful!
First try and it worked. Thanks for the video. 😃😀
Thank you Sir, great instructions and very helpful.
Thanks a lot you save me time I do exactly what you are saying and my remotes work great 👍 Thanks a lot
Worked on 2013 Mazda5 Sport. Thank you so much! This saved me $140!
ptys007 What I found is that this just enables the remote to work. The key still needs to be programmed by the dealership or else it won't start the engine...
+ptys007 *** YES ***this is often over looked. The original remote has a transponder chip which controls the engine immobiliser feature which needs to be programmed by a Mazda dealership or professional locksmith.
Thanks!! I'm going buy your guys remote pretty soon! :)
Worked like a charm
great video, very easy to program
Thank you, this procedure worked on my UK 2007 mazda RX-8..happy days
worked very well with me. Thanks
2012 MAZDA 2 WORKED PERFECT THANK YOU SO MUCH
Im about to buy a 2012 Mazda 2. Thanks for verifying!
@@hagar6908 Good luck wish you the best !
thanks a lot!! worked for my mazda5 and saved me 130 bucks !!
Thanks. It worked with my Mazda 3 2005
Thank you! This worked like a charm. You saved me $288, per the dealer price to buy a new one and reprogram it. I have a 2008 Mazda 3.
I’m going to do this tonight. Also have a Mazda 3 and was nervous until I read your comment.
It’s working thank you so much even works with the car start up
awesome! thank you! worked for me :)
Great! Glad we could help!
Verry helpful. Thanks a lot for this video. Without it I would've not been able to pair the key with my car.
This seemed to odd to me, but to my suprise I was able to get it on the first try. Thanks !
Thank you! You are a blessing!
You are the best. Thanks
This is so awesome thank you!!
Works great, thanks!
Great! Glad we could help.
Great info! Worked perfect!!!
Thank you this worked for my 2010 Mazdaspeed 3.
What key fob did you get?
@@flynn914 i already had a mazda one from my previous car and had used it as a spare to unlock the car IF i ever locked myself out. the key was already cut to the old car so would not start the car but would save my ass as my vehicle then only came with one fob... so if i locked in in the car, i would be screwed, then this video allowed me to program it and presto, worked like a dream. you can buy these fobs on ebay or amazon, most are pretty generic and will work, i tried this on a later car which subsequently i also sold...
Thank you, just did it on a new remote and it worked right away, took about 2 minutes, thanks for the vid.
hi bro, is that the only remote for your car or you do have another one working just add a new one? as I did exactly the same way but nothing happened after press remote botton twice, I heard that there are two different remote for the rx8, which you do you use? thanks a lot~
Great! Thanks for the feedback!
Great work! Cheers mate!
Thanks so much for the vdeo. it was better than instructions that came with the remote.
A little tip if you have a key release button, you don't have to turn the key to the release position each time. Just turning the key from run to the acc position worked for me. I had some issues at first trying to turn it to the release position until I tried it without pushing the key release each time. Just thought I would share in case anyone else was having this problem.
OMG this is literally the only way that it went into the programming mode. THANK YOU
Sir
How i can programming a new reomte but with out old remote.
Just i have normal key!
It works on my mx5 nbfl. Thanks!
thank you very much, its help with my mazda mpv 2003👍👍👍
Thanks a lot. Worked fine with a new key fob from China. 👌
Thanks for your help
It worked. Thank you.
I followed everything he said to program my new additional key for my 2011 mazda 3. Worked perfect. Only problem was it cancelled out my original working key. So I redid the steps and reprogrammed both keys. very Easy. Thank you vey much!!!
I'm worried it will cancel my original key. Did you manage to get both your keys working?
This worked. For my 2012 Mazda. Had 1 working Key and purchased 2 off-brand keys. Went through these steps and now they all lock/unlock the door. Now have to get the 2 keys cut. I am unclear whether there is a chip that also needs programming in order to start the ignition. Just one note. Be sure to do the working key. My first attempt I managed to program the 2 new keys and unprogram the original key. On the second attempt I pressed the unlock button on all 3 keys and that did the trick. Good luck.
+Michael Phillips Yes, there is also a chip in the key that will require separate programming by dealer or locksmith to be able to start the car with the keys. Happy to hear you got the remotes working. :)
+carandtruckremotes how much on average does it cost to get the other (to start ignition) portion programmed? And what am i asking them to do so that i wont get charged for the programming you just showed us. thanks
Great video.. I just replaced my battery Worked first go...there's so many other videos on this but they don't work thanks again
Thanks car and truck Remotes, funciono perfect in my car!!! Mazda 5 , les recomiendo 💯 % ....
Fantastic mate , I got mine working , yah hoo .
Thanks. Worked with Protege5.
I have a 2008 Mazda 3. When I got the car from the dealer, it didn't come with a remote, just a key. I called Mazda and gave them the vin number of my car and they said that my particular car doesn't come with the remote option. If I got an aftermarket remote, would it work? My car has power locks...
Great job thank you
Thank you very much!! Muchas Gracias!!, funcionó perferctamente en mi MAZDA 2 del 2009. I love you :)
very helpful thank u
Awesome works with the 2004 Miata. Easy Peasy.
Thanks works great!
thank you
Not going to lie I thought I was getting trolled. Very surprised it worked!
Hi. I have a 2007 Mazda 6. When I got the car from a dealer it did not come with a remote control. I only have the key. How can I program a remote to work with my car?
Thank you
does this work on a 2007 Mazda 3?
Thanks, worked for 2006 Mazda 3. However, my lock button was acting as my panic button and vice versa. Very frustrating but I finally figured out it isn't a programming issue. I had purchased replacement fobs from ebay and they installed the circuit board upside down. With a small flat head screw driver it's easy to pop open the fob and reverse the circuit board. now if I could only disable that damn panic button...
The same thing happened to me... Tried programming an eBay fob since the battery fell out of my old one, and set off the alarm. But it's not working now so maybe I'll try again
+roverspinne yes it's very easy to reverse the circuit board and I was even able to pry the panic button off the board (just the tiny white button at the top of the apparatus) so the red button is still there but no longer functions
That did it thank you!
what solutions do you provide for the Mazdaspeed 6 (2006)? Credit card style fob for keyless entry and ignition...
It worked thank u
Thank you sir!
is there a way to get the old remote working again after it died during the programming session?