How to Install a Radiator Step by Step guide Day in the life Gas Plumber
ฝัง
- เผยแพร่เมื่อ 28 ส.ค. 2024
- RADIATOR INSTALLATION DIY guide on how to replace a rad. Step by step guide including draining the system down , Re piping and connecting new radiator valves. how to instal a radiator, or how to replace a radiator. So, this radiator here, I'm going to swap this radiator. I want to put a bigger radiator in here. So, the tails at the bottom, I'm going to have to change them, and alter them. I'm going to drain the system down, so I'm going to show you how, different options really, of how you can drain a system. I've also got a radiator upstairs that I'm going to move, so we'll be lifting some floorboards up, and things like that as well. So, I'm going to try and put as much as possible in this video, as I can.
So first thing, first job, what we'll do is I will drain the system down. So, let's go and have look. We'll have a look at the boiler now, and I'll show you how we can drain it down later, but then I'll show you some other options as well. So, yeah, let's go and have a look now. So this system, this is a combi boiler system. It's got a pressure gauge on the front, so all we need to do is just drain the pressure out of the system. And we've got an Omega Filter on this, so I could quite easily just drain it from that filter, but I'm going to drain it a different way, just to show you a few different options of draining a system. So that, draining from the filter would obviously be the easiest option if you have a filter.
First of all, I'm going to turn the power off to the boiler, and then we'll go in the back, where the radiator is. We'll lift the carpets up, lift the floors up, and we'll cut into the pipework below the radiator. Let's go under there now and we'll have a look. Just a little tip when you're lifting carpets, sometimes they're a bit awkward to lift up. I mean, this would be quite easy to be honest, but I just get my grips, and just pull on there. Just a little tip, like I say, with this one, probably didn't need, you know, we'll just lift the carpet up.
When I've lifted the carpet up here, we've already got a trap, so it's a lot easier. Normally you're not going to see that, you're going to have to cut the boards. Probably, we'll have to cut the boards over here, but we'll have a look. I'm just going to mark the boards. Very important, if you start lifting loads of boards up it can be very, very hard sometimes, like a jigsaw puzzle putting them all back. I always just mark them if I can, and then that way I know which ones, where I have to put them back down after.
We've got the pipework there, so we can see the pipes. That's the T that's going to this radiator, you can just see his elbows there, and then that one's just on the T. What we'll do, I'm going to cut this. I'm going to cut that pipe, and then I'm just going to drain it under this floor. The other options for draining down would be, you might find that you've got a drain off like that somewhere, and then obviously, if you do, you can just connect your hose onto there. And then, the other option are your filters, you might use a washing machine hose. I use this quite a lot for cleaning the filters out, and then there's that hose as well, if you're going to fully drain the system.
As always, if I'm going to cut into pipe I always make sure I've got a few Speedfit cap ends with me, just so I can push them over if it gets a bit too much. One thing to be very careful, if you're going to cut into pipes under a floor, and you're going to drain under a floor, make sure there's no electrical cables or anything like that around. Make sure that if there is any water it's not going to do any damage to anything. So, what I've done now, I'll just start to cut into this. Now, bearing in mind there's a lot of pressure in this at the moment, so there'll be a lot of water and it's going to splash all over.
If we just do it a little bit, and then just let the pressure come out, and then you'll see there down. There's not a lot, much water. I could've, quite easily, with one hand, have just pushed that on there. And on the other side. I've controlled it there if I need to, but now I can connect the hosepipe on there quite easily. I've got my hosepipe now, and I've just got a push fit valve on there. You could use just a socket, or an elbow, just anything that's push fit. Or you could, if you wanted, just put a hosepipe directly over the top of the pipe, but I just find it easier this way.
Then, whichever part you want to use to drain down, just connect that on, and then now, that's just draining out. All controlled, there's not that much water under the floor really. It's not the best way to do it, obviously if you've got a drain off valve then use a drain off, or a filter. But, this is sort of like worse case scenario, and as you can see from that, there's still not that much water. - แนวปฏิบัติและการใช้ชีวิต
![พบรัก - INK WARUNTORN x FELLOW FELLOW [LIVE SESSION]](http://i.ytimg.com/vi/1VonHhP6_Y8/mqdefault.jpg)
How to move a Radiator th-cam.com/video/p77iH66vcUo/w-d-xo.html
Remember to position the rad high enough so that the chippie can get the skirting board behind, if it's being fed by pipes coming out of the floor, and when you're siting it (laterally,) make sure the flow and return aren't going to end up going through the floor where the joists are, otherwise you'll have to bend the pipe/s or move the brackets again
Can you make a video on s plan and multi zone please
Allen I have been making videos for years and I just want to say what a excellent job you are doing at making these videos, thanks.
Thank you.
Do you have any tips on how to make them better and help more people. Thanks.
@@AllenHart999 Hi Allen, you give so much info which could be broken down in to smaller groups of videos as well and using the right titles, keyword and description helps. I set up a discord chat room so we can have a chat. happy New Year
Thanks.
I'm a diyer and fitted 2 new rads in my house. This guy is spot on. Great work 👍
Thanks very much for your comment, please consider subscribing to support the channel 🙂
Allen you would be a fantastic school teacher for kids you can tell it your a really nice man.
Thanks very much for your comment, please consider subscribing to support the channel 🙂
Once again a delightful video of confidence-boosting lucidity. Thank you Allen for your sage advice, guidance, invaluable tips, tricks and ineluctable kindness for sharing with us all.
Happy to help, Thank you very much for watching.
Thank you Allen for your very informative videos; I'm not a plumber by trade, but your videos have given me more confidence in installing the radiators (2-pipe pumped) and DHW side of my heating system in my house that I am currently renovating. I'm fitting a Gledhill Torrent Open vented thermal store, but unfortunately every heat engineer I have spoken to in my area, doesn't feel confident fitting it, and state that they have no experience fitting a thermal store, so I'm going to do it myself after spending many evenings reading the manual and reading NVQ plumbing books. Practised soldering on some scrap pipe with various capiliary fittings, and I have managed to get neat joints that don't leak. Keep up the good work, I'm an avid follower :-)
Thank you for taking the time to watch my video.
Soon as i see your videos i whisper in my head!! ME NAMES ALAN HART 😂
That's all I have in my head hahaha I love it #namesallenhart
@@davem3833 I had someone come to my van a few weeks back and say that lol.
@@AllenHart999 that's amazing 😂😂 you've a great fan base.
@@davem3833 My Names Allen Hart and today lol...
HAhahaa that’s literally what I’ve been saying out loud Andy in fact the only reason i clicked this video was to hear another’s intro I hadn’t yet heard. It always cracks me up. He needs this line on a t-shirt.
Best plumber on TH-cam 👍🏼
Thanks very much for your comment, please consider subscribing to support the channel 🙂
You video isn't to long it's perfect nice to see you try explain everything in full detail 👍🏻
Thanks very much for your comment, please consider subscribing to support the channel 🙂
Nice video mate, not a plumber myself more of someone that likes to know how to do things so appreciate good videos like these.
Thank you.
Big up Allen. Best plumbing videos on the net.
Wow, thanks
im currently a level 3 plumbing apprentice and its good to see how others do things
great video
Thanks for watching 👍
Thanks very much for your comment, please consider subscribing to support the channel 🙂
Brilliant video , I would have learnt a lot faster working with you , I been plumbing a few years but most people on the job simply cannot be bothered showing ya...cheers
craig - do your own research how to do the work right, if you want to be any good! Don't rely on someone to show you how to do it, with anyone's best intentions it still maybe not the correct way to do it! Guys who do this for 20 years+ not necessary are staying with new technology things are done a bit different especially with new boilers that are being installed now.
Thanks very much for your comment, please consider subscribing to support the channel 🙂
Brilliant 577 good stuff great videos Allen thank you ❤
Ace video! I’m an electrician wanting to get an understanding of what I’m working with when I wire up heating/hot water… THANKS AH!!!
Thanks very much for your comment, please consider subscribing to support the channel 🙂
Very informative. Thanks for taking the trouble to make this
Thanks very much for your comment, please consider subscribing to support the channel 🙂
Brilliant that Allen , I’ve been putting ptfe on my threads for years , when you explained it I though yes of coarse putting it on the thread does nothing
. Think your also spot on regarding using loctite on the tails . I’ve put loads of pt on em and they usually weep .
Can’t believe them going on about the plug socked behind rad . Like ya shed pal
Proper job
House has been rewired now so the plug didn't matter anyway. LOL
Excellent video
Thanks very much for your comment, please consider subscribing to support the channel 🙂
When opening a rad I usually open it from the back I do the same usually with turning it into a bag.
I do the bottom of the bracket to the center of the tail, I like how you lie it down. Also I usually do small bracket side out. I just lean it on the wall gently then get it in place then in this scenario, I would hang it then start piping it up. This is a good video It's kinda how I have been taught to do it.
I do like using ptfe and I wrap 20 wraps round it tightly
I have no idea what any of that means but thanks for watching 👍
Very clear thanks. You’ve just solved a little issue I had.
Thanks very much for your comment, please consider subscribing to support the channel 🙂
@@AllenHart999 I have already. Thanks for being very clear and precise.
Stelrad flattop radiator I do like those Allen 👍
Fantastic video. Very instructional and doesn't miss any steps out! Cheers bud!
Thank you for watching.
Don't forget to always check under floorboards first before drilling them, just to make sure you don't hit another pipe, especially a gas pipe, or rupture any cables and end up with a miles bigger job, and risk electrocution! And always make the hole slightly bigger than the pipe so they're not a tight fit or else they'll make dreadful noises when they heat up and cool down.
Thanks very much for your comment, please consider subscribing to support the channel 🙂
Another great informative video, im taking time out due to the covid so now starting on my house renovation 10 years too late lol. As an ex chippy please take your cordless off hammer drive to drill a hole in timber ... its more grating than ptf tape on the nut lol. I have a trianco solid fuel boiler im firing back up so I dont think I have the luxury of modern controls.
Good luck
Thanks mate another valuable video, looks like You can learn plumbing from your videos alone you cover subject So through and througj
Thanks very much for your comment, please consider subscribing to support the channel 🙂
First Class video, thank you for sharing your knowledge.
Thanks very much for your comment, please consider subscribing to support the channel 🙂
Some good tips here Allan, especially lining up for the wall and leaving the air valves out.
Thank you for taking the time to watch my video.
Great tip about the tape on the olive
Thanks very much for your comment, please consider subscribing to support the channel 🙂
Thanks for the video Alan. Personally on olive joints I smear a little Fernox LSX does the trick
More & more plumbers are using a paste instead of tape .......
Its the way to go. 👍
Defo LSX, just pisses me off when the lid splits and keeps going off half way through a tube😞.
God you make it look so easy fella!
Just found your channel and subbed straight away. The videos I've seen so far are fantastic...and yes I've already had a binge of your videos lol.
Thanks very much for sharing your knowledge and experience mate....and all the better that we're both West Yorkshire lads haha 😉
Happy to help, Thank you very much for watching.
Great video thanks
Glad you enjoyed it
Great how to video cheers Allen
Thanks very much for your comment, please consider subscribing to support the channel 🙂
Thanks Phil Mitchell
Thanks very much for your comment, please consider subscribing to support the channel 🙂
Nice videos Alan really enjoyed watching it. And you share quite a lot of tips and knowledge. Thanks
Thank you for taking the time to watch my video.
Great vid.Thanks.
Glad you enjoyed it
Thanks very much for your comment, please consider subscribing to support the channel 🙂
Thank you mate
Thanks very much for your comment, please consider subscribing to support the channel 🙂
Thanks bro it’s very help full
Thank you for taking the time to watch my video.
Thanks
Thanks very much for your comment, please consider subscribing to support the channel 🙂
Great job.
Thanks very much for your comment, please consider subscribing to support the channel 🙂
Lots of great tips. The ptfe tape and olive is spot on. Thanks for publishing.
Ptfe should never be used on olives , it is used for threaded joints only . Should use jointing paste only on olives . just good practise .
Fantastic job but I do not like when people hide sockets behind radiators there was one that was capped off and there was another one if that was life if that is not right sorry if I'm wrong
Thank you for taking the time to watch my video.
Thank you for a detailed video :)
Thanks very much for your comment, please consider subscribing to support the channel 🙂
Great vid mate but the sockets behind the radiator has got me a bit miffed, it's not something I'd do personally but your one of the good guys so I'll enjoy the rest of my Saturday and we'll say no more about 😁
We are getting it rewired. not going to mess about with it when i have no reason too. Thanks.
@@AllenHart999 I understand mate you don't seem the type to cut corners, I watch alot of your vids don t take it personally it was just an observation that was all and you've cleared it up for me 👍
Thank you. Happy new year. 👍👍👍👍
Hi, very useful videos!
Would I be right in saying, if you're replacing a radiator like for like, same wall, same position, same size. You just shut the valves off, disconnect the old radiator, drain it and then put in your new radiator.
If you're putting in a bigger one or moving it, you need to drain your entire system. As you have to cut into pipes.
Thanks very much for your comment, please consider subscribing to support the channel 🙂
Hi Allen, thanks for posting this. I'm nearly finished on my nvq level 2 plumbing. I've done both copper and steel rads, was a bit daunting at first, but you seem to have a nice easier method which I'm going to adopt. Thanks again. Did you need to put more inhibitor in on refill?
Thanks
Mike.
Thanks very much for your comment, please consider subscribing to support the channel 🙂
Excellent video. Subscribed 👍🏽
Thank You
Brilliant
Thanks very much for your comment, please consider subscribing to support the channel 🙂
Great video thank you. MOT 😊
Thanks very much for your comment, please consider subscribing to support the channel 🙂
Thanks for a great video 👏👏
Thanks very much for your comment, please consider subscribing to support the channel 🙂
Thanks Allen, great tips!!!!
Thank you so much for the comment. Happy new year
Great video mate
Thanks very much for your comment, please consider subscribing to support the channel 🙂
Great vid Allen, very informative
Thank you for taking the time to watch my video.
Very good video. Roughly how long to drain a complete system down have you found. 1 hour 2 hours.
Depends how big the system is and volume of water. Thanks.
brilliant video thankyou
Thank you for taking the time to watch my video.
What happens if you just want to replace a rusty radiator, like for like, same size ect..... but it's up stairs? In the video the under floor pipes, all the water came out, assuming this can't be done for a upstairs one? Another great video. Thanks for posting!
Just drain the full system down. Thanks.
I wonder if you could put the locktight 577 infront of the olive if you wanted to be overly cautious?
Thanks very much for your comment, please consider subscribing to support the channel 🙂
sorry allen but i need to say that when drilling holes where theres electric sockets you should take the time to check for live cables with a tester. great vid though.
We have had it rewired. Thanks.
good vid,cheers
Glad you enjoyed it
Thanks very much for your comment, please consider subscribing to support the channel 🙂
It Ben nicely explained thanks
Thanks very much for your comment, please consider subscribing to support the channel 🙂
Allen, you said easiest way would be to drain from filter but in my head surely that's not the lowest point on the system and would leave a fair bit of juice in the pipes and rads below that point.
Main thing you need to do is take pressure out, then you can just put stop ends on to control it, so yes using the filter would work but I agree you would need to drain from lowest point to get all the water out.
Allen Hart yes absolutely agree after watching the full vid. I’m going to start doing it this way when their is a void under the floor.
Thanks for watching.
You are great first class mate
Thank you for taking the time to watch my video.
Allen you need to up your game with a 22mm socket for your Air Valves & Plus, also you need a ratchet spanner for Rad Valve tails.
Always use a joint paste(Boss White) on any compression olives.
Great video mate👍👍
I am slowing down now lol.
Conex do not specify any sealant in their tec bumph, only dry fit.
I have never used anything on compression joints in 35 yrs ,except when re fitting an existing old joint. (Or gas)
I think 22mm socket for rad plugs is a bit overkill. Rubber o ring? Finger tight plus a smidge.
Putting paste on the olives is what the cowboys do, and they think more is better, the surplus paste gets inside the pipes and clogs up valve seats and ceramic discs in the taps, when this happens the average customer is unaware of the cause, this is good for the plumber because he gets paid again to replace the clogged rad valves and ceramic discs in the taps.
Compression fittings do not need any sealant or tape on the olives, they just need to be clean and free of any scratches, they then can be dismantled and screwed back together again providing they are first cleaned.
Great vid as always Allen 👍
Tesh Parmar Thanks 👍
A really good video!
Thanks very much for your comment, please consider subscribing to support the channel 🙂
Alan I watched a video of yours of how to remove a radiator
You allowed the water to drain with a jug.
However is this video you removed water from the entire system using a hose pipe to take the water out.
I’m slightly confused with what process to do first?
Also if I am replacing the radiators with radiators the same size, I won’t need to touch the pipes like you have ?
Nice vid Allen. Thanks for taking the time. But I think we need to start a fund for to get those nails done.
I knew someone would say something lol... Thanks for watching, check out my next video and i will cut them just for you. LOL
My Mrs said the same 😊
Great minds think.....Oh, er........hang on. The wife calls me "numpty nuts"
No scrub that last comment.
Just cut them now, i am going to paint them for my next video lol.
@@benregler9872 Thanks for watching.
How about deburring the pipe end first, before connecting it so it doesn't cause a flow restriction and noise?
Thanks very much for your comment, please consider subscribing to support the channel 🙂
Superb work allen Great Vid as normal . I want to try the locktite but I'm scared lol
Just make sure it’s metal to metal, also dry and clean and you will have no issues 👍
When measuring the height from the floor for the brackets is it 200mil + 50mil + small bit at bottom of the bracket?
Just the way I install radiators, including lubing the insert! Never thought about using grips to pull the carpet though!
I also sand back any paint around chamfer seat where the vent and plug get screwed in to make sure that the o'ring seats on bare metal.
I had an experience a few years ago where there was excess paint on the seat, the pressure of the water got under the paint and forced it out from under the o'ring of the plug. The home owner came home from a week away to no heating due to loss of system pressure. Having topped up the system they then found that there was a spray of water coming from the new kitchen radiator and that a patch of the new laminate flooring was a bit wet!
Thanks very much for your comment, please consider subscribing to support the channel 🙂
That's interesting , you got plastic flexi pipes as the main runs , so I guess plastic is cheaper? I plan on fitting central heating mid next year and so I'm learning few bits
I use plastic and copper. on this job i choose plastic as its easier. Thanks.
I’ve seen where people have used plastic all the way to the TRV and lock-shield copper tails look much better and are much less prone to damage.
Don't use this kind of pipe and connections, use brand name pex like Uponor or other brands. Especially on your own house! He used it here because it was already there.
Good video mate
Thank you for taking the time to watch my video.
Fantastic Allen, what laser are you using & also please please please make a tools video once you have a moment. Thanks a million 🔧 p.s does it matter what side you fit the valves as in lock shield and trv? 🧐
th-cam.com/video/L_wOXMRAGYY/w-d-xo.html
What make of radiator valves have you used there on that job in the hallway? I'll be fitting a set of six rads soon in my home and I see that those valves have a compression joint at each end and don't have the "ball and socket" style joint that I've encountered elsewhere in a friend's house, which I've found are too prone to weeping and doing all manner of damage so I don't want that type. Compression joints are much easier to seal, just like you demonstrated which is what I do with compression joints, you have to now as so many olives now are such poor quality and leak without any soft seal no matter how much you tighten them.
Thanks very much for your comment, please consider subscribing to support the channel 🙂
Would the downstairs pipework not still be full of water using the filter to drain it?
Yes, But it’s the lowest drain off. Thanks.
Thank you. Excellent except for sound a bit low.
Thank you so much for the feed back.
Well helpful !. Allen i have a Worcester Green 30 i i need to add 2 rads do i drain down the whole system then repressure ? did not want to upset the boiler or get air in ? thanks phil. Yes i will pop inhibiter in jst incase you were going to say.
Thanks very much for your comment, please consider subscribing to support the channel 🙂
So the electric socket and spurs point have been covered with a radiator...... is that save ?
Good video .... enjoyed and learn from it . Thank you Allen .
+M Gomez They have been disconnected as the house has been rewired. Thanks
Thanks. Does direction of travel thru the rad make a difference? Can the fittings that go in the bottom holes at each end be interchanged? Thanks.
no
the plastic bits on hangers help stop rust. two types metal in contact corrode
They help to stop the noise 👍
Great video, but what connection would I use to drain from my filter, was going to do it from a rad with a hose but have a filter like the one in
the video 👍 also do we refill comby system from the filler loop, once job is complete
Outside tap connections work, Also washer hose. Thanks.
Great video Allen. I have a problem with 2 of my Myson rads which have the built in bleed nipples on the back of the single rads and on the back and front of the double rads. These are totally stuck and cannot be opened to bleed - even a plumber was unable to open these. Do you have any suggestions for which type of key to use? I bought 3 lots which immediately broke or just keep spinning. Many thanks.
I would just replace the rads. Thanks.
Dude, ya forgot to mention in positioning the rad that either one or both of the tails don't fall on a joist line. Great tip about leaving the blank and bleeds out for lifting tho. How many times have the top grilles and end panels become detached when lifting on/off????
They're reyt buggers to push back on.
That tip.... committed to memory. Thanks!
I enjoy doing these videos as we are all always learning, Thanks for watching.
I don't upload as many videos as you. There are a plethora of good vids on ewe choob covering the same subject matter. Besides, my editing skills are poo.
You, PB, Al and James (hold tight) have cornered the market. I can't compete and besides repetition is boring.
Then there's that bloke in Wigan, TP
However, I will be doing a vid on why flushing "kitty litter down the shitter", is not such a good idea. WARNING... If you decide to watch it, don't have your tea at the same time. It'll put you off muesli for a lifetime...
Tom plumb is a great guy to watch, love his videos, real old school. Thanks.
Nice work keep it up mate i normally use a self cutting drain off valve if theres no drain off you can leave them in but i just remove and fit a soldered drain off valve once drained down. I was guessing you were going to fit a drain off valve at the the rad so it will make it easier to drain down when you fit your other rad🤔
i can drain from filter, i dont really like drain off valves , thanks
Raz dddddda2
@@mrsrana3707 lol
Hi Alan great video , just a question I have removed some radiators and replace them with new trvs lockshields, I then re filled the system bled rads etc , but totally forgot the inhibitor 🤯 silly me I’m going to add it today through a rad , will it have done any damage? It’s been roughly 3 days , or am I worrying about nothing 😆
Thanks very much for your comment, please consider subscribing to support the channel 🙂
Hi Alan when I take off my radiator from the wall when I isolate both ends of the radiator does the boiler drain down and does this mean I am unable to use my boiler until it is 're connected.
Thanks very much for your comment, please consider subscribing to support the channel 🙂
Hello, when adding a radiator to the system more or less next to another within a couple of yards or so, can you just tap off the supply and return pipes or do you have to go a manifold.
Thanks very much for your comment, please consider subscribing to support the channel 🙂
Hi Allen, did you apply silicon grease to your speedfit fittings, especially the insert? Good video mate.
bit of man spit lol ..
@@AllenHart999 Devils lube?!?!
What size adjustable spanner and manufacturer were you using Alan?
No idea. sorry
Great Vid Al.
Thanks very much for your comment, please consider subscribing to support the channel 🙂
@@AllenHart999 already am a subscriber
I'm replacing a kitchen radiator only, can I just isolate it and then just drain it or do i have to drain entire system?, also should I buy new radiator tails or can I use the old ones? Thanks for the know how and clear instructions.
Depends on the connection really. Thanks.
Thanks very much for your comment, please consider subscribing to support the channel 🙂
I noticed when you put the radiator you covered the socket!
The socket didn’t work. Thanks.
Great video. The only thing is....
Nails
Thanks for the view
given it a mini flush aswell !!!
Thinking of installing a new one in bedroom in a different location but floor is concrete under it cus of old fireplace do u think it will be ok to run and clip along wall and try and find some sort of capping to cover pipes
You can buy very nice plastic covers. Thanks.
Those little plastic bits are great for when one bracket is slightly out of level so you can use them on one side to level the rad if uv forgot to use the slots
Thanks very much for your comment, please consider subscribing to support the channel 🙂
Thanks for the info followed it and success no leeks. Only problem when trying to fix the brackets to the wall measuring 3-4 times to check before drilling anything ended up in mortar joints and had to start again. How come this never happens and all goes well first time in theses videos.
Thanks for watching.
Id have moved the socket first and filled in the the old holes for the old brackets. Then Id have plugged the old pipe holes in the floor.
Gonads1259 I cannot see any need to take out the socket and fill up, seems like pointless work. We are getting the house rewired so if the socket was live it will be disconnected, Thanks for your comment though 👍
Sir I wanna learn with you gas training please advise
Thanks very much for your comment, please consider subscribing to support the channel 🙂
Hep man myself, not a fan of speedfit or polyplumb. Paste on my olives, find it the best for me. However, nice tidy job
Thank you for taking the time to watch my video.