This is a video from a few years back that was once in three seperate episodes. I've joined them together to help people do this whole job easier. If you've seen it before, IGNORE! New video out on Monday (I hope!)
Nice job .my daughter's just had all new chrome radiators fitted wow they look amazing...😢 You can fry an egg on them but no heat radiates from them ..can't get the house above 19 degrees wish plumber had mentioned something about chrome rads...
How would you take the radiator off the wall for painting behind the radiator, as i have the same valves and you cannot move the pipes left or right without damaging the wall.
What if I want heat in my home in NC and have been considering installing a whole system. Can I just buy an electric boiler, pex and a bunch of radiators?
If i were to add anything to this video it would be this, Upon turning on the system after re-filling i always put boiler temp down low to minimise overheating which can happen with air going round the system, and once flowing well i would put boiler temp on full load to test that the expansion vessel (if it has one) or that the water level in the F&E tank doesnt reach its limit, as you would be altering the expansion rates, it may also need a larger expansion vessel or to re set the water level in the tank... The IR camera is handy to make sure all radiators are circulating at the same or similar speed. Be mindfull not to restrict the cylinder lockshield loop valve too much as in the summer your boiler would end up cycling on and off way too much. Hot water is designed to take priority and if the boiler water is set higher than the hot water control stat then it will do its job and switch off..
Not forgetting the new trv’s that you preset for balancing need putting on the feed. Take a photo as well as a diagram. Great video with some good advice.
Does anyone know what type of insulation that is under the chipboard? It looks like foil wrapped fiberglass but can't find it anywhere. I'm renovating and think it would be great to put something like that in! Thanks
Alot of new designer radiators are flow sensitive and will have a plug 1/3rd the way along from the flow entry point... this helps divert the water upwards.. if the rad isnt marked up as inlet/outlet then the best way to check is to physically look down the connection points or poke something in there. If that makes sense.
Depressurise it. Drain some water out then go to the highest radiator and fill it by removing bleed valve and a funnel. Or if you have a magna clean filter, turn both valves off, empty the water out of the filter and fill it with inhibitor.
Is it normal to have all that installation under the floor.... My house is 15 years old and has NONE!!! plasterboard ceiling, pipes and wires, chipboard floor
Unimpressed with the piping that goes up to the Rad at 24:20. In my opinion it's far too close to the skirting and has a horrible looking bend in it. Would be better for looks and future skirting painting if it was away away from the skirting.
@@plumberparts I don't know why this is the case but I would imagine it's to try to avoid people adding radiators from the main houses system to something like a uninsulated conservatory.
Ooh James James James. Nooo ! What if you were in a meeting and the speaker referred to everybody as "YOU GIRLS". Do you think all the men would object so much. Can you now see that saying "YOU GUYS" is so sexist and demeaning to women. If I was a woman, I wouldn't want to be classed as a guy. Please show that you care by getting onboard to stop this and give women their space with kindness. 🤔 Okay people.
What if I want heat in my home in NC and have been considering installing a whole system. Can I just buy an electric boiler, pex and a bunch of radiators?
This is a video from a few years back that was once in three seperate episodes. I've joined them together to help people do this whole job easier. If you've seen it before, IGNORE! New video out on Monday (I hope!)
What tune is it ? 32 minutes
Nice job .my daughter's just had all new chrome radiators fitted wow they look amazing...😢 You can fry an egg on them but no heat radiates from them ..can't get the house above 19 degrees wish plumber had mentioned something about chrome rads...
I use to pressure test with a small compressor. My knees hurt just watching these clips 👍👍👍
Thank you James much appreciated from a novice diy.
A very good firday evening to you all from Wellington Somerset
Brilliant tip on the motors
👍👍🤜🤠
Looking much better in this video than in the newer ones
9:47 you talk about the flow diverter for the tall rads. Do you recommend a version that can be retrospectively added to an existing rad?
Cool video as always, didn’t manage to catch the model of SDS Bosch drill, which one is it please?
Great videos mate
What pipes are those and how do they vary from the usual white rad flexy pipes?
Love these videos but what would you say is wrong if heating is working but no hot water
Do you have a combination boiler or separate boiler and water heater?
Hello, could you kindly mention the press tool you you are using in this video. I have checked the link you had mentioned but could not find it.
How would you take the radiator off the wall for painting behind the radiator, as i have the same valves and you cannot move the pipes left or right without damaging the wall.
Very informative
What if I want heat in my home in NC and have been considering installing a whole system. Can I just buy an electric boiler, pex and a bunch of radiators?
20:55 oooh shots fired 😆😆😆
If i were to add anything to this video it would be this,
Upon turning on the system after re-filling i always put boiler temp down low to minimise overheating which can happen with air going round the system, and once flowing well i would put boiler temp on full load to test that the expansion vessel (if it has one) or that the water level in the F&E tank doesnt reach its limit, as you would be altering the expansion rates, it may also need a larger expansion vessel or to re set the water level in the tank... The IR camera is handy to make sure all radiators are circulating at the same or similar speed. Be mindfull not to restrict the cylinder lockshield loop valve too much as in the summer your boiler would end up cycling on and off way too much. Hot water is designed to take priority and if the boiler water is set higher than the hot water control stat then it will do its job and switch off..
Have I dreamt a video about a bore hole or is it just still in progress?
How do you determine how many new radiators your boiler can handle?
And how do you decide when to use plastic and when to use copper pipe? Thanks.
Not forgetting the new trv’s that you preset for balancing need putting on the feed. Take a photo as well as a diagram. Great video with some good advice.
Does anyone know what type of insulation that is under the chipboard? It looks like foil wrapped fiberglass but can't find it anywhere. I'm renovating and think it would be great to put something like that in! Thanks
Hang on,,, how did the wall get skimmed and the skirting fixed on.....🤔🤔🤔🤔🤔👍
im a kid but i help my dad with heating
How can you tell if the rad has already got a diverting spring thanks.
Alot of new designer radiators are flow sensitive and will have a plug 1/3rd the way along from the flow entry point... this helps divert the water upwards.. if the rad isnt marked up as inlet/outlet then the best way to check is to physically look down the connection points or poke something in there. If that makes sense.
I've got a question please. How do you get inhibitor into a pressurised system?
Depressurise it. Drain some water out then go to the highest radiator and fill it by removing bleed valve and a funnel. Or if you have a magna clean filter, turn both valves off, empty the water out of the filter and fill it with inhibitor.
Is it normal to have all that installation under the floor.... My house is 15 years old and has NONE!!! plasterboard ceiling, pipes and wires, chipboard floor
Oooh i just added one... Wonder if i did it right!!! LOL too late!!
How unusual to have insulation between the floors, unless the downstairs room used to be an unheated garage or something?
Unimpressed with the piping that goes up to the Rad at 24:20. In my opinion it's far too close to the skirting and has a horrible looking bend in it. Would be better for looks and future skirting painting if it was away away from the skirting.
How come you built a whole stud wall instead of just chasing pipes into existing wall?
Because of the returning glass screen.
Using buteline is cruel for the next guy that comes for a repair,you horrible bastard 🤣🤣🤣🤣👌🏻
Fuck the next guy lol unless it’s you again!
What's the difference between this pipes and the normal flexi pipes?
Would of been easier if you had a laser 🤷🏼♂️👍
This is already been posted
Clock in the kitchen says 2020 😉
James too many ad breaks
Adding a radiator to a heating system requires building control signoff.
Ha! Clown world isn’t it? 😂
@@plumberparts I don't know why this is the case but I would imagine it's to try to avoid people adding radiators from the main houses system to something like a uninsulated conservatory.
Ooh James James James. Nooo !
What if you were in a meeting and the speaker referred to everybody as "YOU GIRLS".
Do you think all the men would object so much.
Can you now see that saying "YOU GUYS" is so sexist and demeaning to women.
If I was a woman, I wouldn't want to be classed as a guy.
Please show that you care by getting onboard to stop this and give women their space with kindness.
🤔
Okay people.
What if I want heat in my home in NC and have been considering installing a whole system. Can I just buy an electric boiler, pex and a bunch of radiators?