Mikrotik Route Load Sharing (LAN1 to WAN1 and LAN2 to WAN2)

Mikrotik Route Load Sharing (LAN1 to WAN1 and LAN2 to WAN2)

[@johnjay3966]

Perfect. Used this tutorial as startup configuration to switch internal caps to internal traffic and guest caps to external traffic, with capsman and 2 SSIDs

[@chinedudeoracle]

I used the configuration as taught here and all is working fine, but I have an issue; when in LAN1 i can ping the gateway but i can't ping other clients in LAN1, please can you help?

[@huangbochn]

thank you very much.

[@davelodia9157]

Very good tutorial, Mikrotik Route Load Sharing (LAN1 to WAN1 and LAN2 to WAN2) can you add the HotSpot for this tutorial?

[@dawidtrojanowski6374]

super thanks

[@PhallaCCMT]

+Dawid Trojanowski :)

[@garz712]

hi, where did you get the routing mark - "WAN1-LAN1" and "WAN2-LAN2"... configuration not shown on the video... can you show the details for that routing mark...

[@eliasalonso8459]

hi could you configure it?

[@jecalad]

If i don't want to separate traffic , the video ends for me at 5:05?right? And the mikrotik do the the load balancing automatically?

[@franksambiase]

Very good tutorial, but how can I solve the problem of portforwarding(d-nat) and sticky sessions related portforward(dnat)? Thanks

[@eliasalonso8459]

hi! sorry but in the minute 8:00 onwards, he select en routing mark "WAN1-LAN1" but that was not the one he configured before !! somebody can i explain!

[@johnmikky9517]

I noticed too...Does anyone have any explanation to this please?

[@djshaunvt]

@@johnmikky9517 What do you want to know... Do you Make traffic exit the same WAN interface it came in ???????????

[@khorshedalam1705]

Most demandable tutorial. Will you please provide any text note for batter understanding? After all thanks a lot

[@davelodia9157]

any update to my request to add hotspot for this tutorial?

[@PhallaCCMT]

+Dave Lodia : will upload once available

[@Setup_ve]

How can I with Wlan1 to Wan1 and Wlan2 to Wan2...

[@Sendotakeshi94]

Thanks for this tutorial, it works but I have 2 problems :
1. hosts on LAN1 cannot reach hosts on LAN2
2. cannot ping public IP of WAN1 and WAN2
How can I do to resolve those problems ?

[@miroslavpetrasek4328]

I have the same problem, I must use two RB , make Ip tunel and set routes criss-cross from one RB to other.

[@PhallaCCMT]

Create accept rule from Source LAN1 to Des LAN2 and Source LAN2 to Des LAN1 in mangle

[@PhallaCCMT]

Create accept rule for any destination you want

[@arielpablobran5056]

@@PhallaCCMT
I create the rule but it doesn't work.

[@user-ei5pd3dc4x]

mark routing!!!

[@georgewashington90]

Can you improve video quality? Most of it I must guess.

[@PhallaCCMT]

Video not HD?

[@mohammedaljuneid5902]

nice way ok ...
me i have 2 wan and 1lan , and i want to separate users some of them use wan1 and others use wan2 >>>> what's way to doing that ? pleas hellp me

[@sonfromheaven]

after reboot
it again asks for installation of the softwares, i press "a" and then
"i". it reboots and again same cycle goes on. help please.
note I am using virtual box.

[@nahidrauf1464]

Yasir, you need to remove your installation media. The CD / DVD or the drive from where you installed RouterOs for Mikrotik. Alternatively, you can also change your boot sequence to avoid such problem.

[@dreamonstudio7469]

I set VPN server on my mikrotik na RDP is working ok via VPN, but when I add mark routing RDP is not working via VPN can you tell me what other step I need to do to sort it this problem

[@esantos999]

I have the same problem in the same scenario. Have you figured out how to solve it?