I almost had mental breakdown trying to switch these tires:) Too say it´s difficult is an understatement, Xiaomi should tell you "changing tires is an almost impossible task if you happen to have a flat".... then I went to the cycle repairshop next to me, he too almost had a mental breakdown but after a while managed to do it:)
Had same thing at my bike shop 😂😂 finally replaced the front tire last night myself and I wanted to break things. Just as I got to work the front tire went flat again.. Oooo that was fun
I curse a day when I bought this garbage. Changing tire is just a torture. I am so angry right now and my hands are all red. thanks for the video though
ben Cooper I got solid tires as well the ones you described with holes. I didn't put it yet on I am mentally not ready to go through this hell again :) In a meantime I got a new scooter falcon ZERO 10x. Its very big and heavy but much better quality, smooth ride because has suspension and I feel safer now
ben Cooper this is too accurate the valve is damn near impossible to get off and the tire is hard as a bitch to get off and my solid tire probably isn’t event gonna be able to be put on in the time frame that I have. Same thing happened to me. First the rear tire goes and I put a solid tire on that and now the front which is already a nightmare and I haven’t even boiled the tire
ben Cooper I change fI'm tire to solid as well. now its horrible I don't enjoy riding it at all. I have feel every single thing on a road :( I think it can only be an option for somebody very light weight
ben Cooper I am 94 but you are right. as long as those damn punctures won't happen again its worth it. Also you kind of get used to a less smooth ride :) Also I've noticed that experience may wary depending on type of shoes I'm wearing
Reading all these complaints, I just wanted to point out that indeed, first time is challenging AF and it took ages, but the key is not to heat up the tire or to apply a crazy amount of brute force, key is TO USE THE RIGHT TOOLS trust me!!! It looked like and odyssey without them, once I used 2 BAR CLAMPS to hold the main part in place and some metal bars for leverage to put the final part of the tire in, it became surprisingly easy!! For the valve, if the hole is also annoying you, carefully enlarge it A BIT with a drill. Be safe though and good luck :)
I did it! It wasn't easy for sure. But it also wasn't impossible. To get the valve out, I used and allen key that was about the same size as the valve stem and tapped with a hammer. It actually went way better than expected. The real hard part was getting the tire back on. I boiled it in water and used a grease lubricant on the tire wall and on the rim. The key is having long tire irons/levers. Mine were short which mad it really hard. I ending up using one short tire lever, one regular flat head screwdriver, and the key to finishing it was a long flat bike pedal wrench. It's all about leverage. If I do this again I will definitely invest in long tire levers and maybe enlist a second set of hands to help hold the levers down (I used two hands and a foot.) Best of luck!!
Hey! Usually I don't write TH-cam comments, however you literally saved me a time with a spoon usage! I spent hours trying to remove a tire, however only your method worked. Thanks a lot!
Don't let the simplicity of this video trick you, it's a nightmare replacing this tire. All the tricky parts (the most difficult parts) have been edited out from the video. For example, He did not show how he got the air valve in/out for example. Maybe because he did not insert the inner tube. Pay attention toward the end of the video, there is no air valve in the hole. Long story short, replacing the tire is very difficult and frustrating.
Exactly, where the bloody hell is the inner tube?? I managed to do this but by the end I completely destroyed the inner tube...back to the droving board!!
THANK YOU! Vaseline and 2 minutes in the miccowave warmed the tyire up enough that I could just stake on it, jiggle about a bit and it slid right on. Having said that, I needed a dremel to cut the inner tube valve - somehow its too long to actually come out.
Good clear video however a question? how does a normal microwave heat rubber? I would recommend using a hair dryer to heat the tyre or a conventional oven also vaseline will stay on the rim and you run the risk of the rim slipping on the tyre under power, much better to use small amount of soapy water which will evaporate and leave no residue. Tyre levers cost less than a dollar? spoons? if people arent replacing tyres with solid tyres you run the risk of pinching the innertube using spoons, just get cheap plastic tyre levers if replacing the innertube. If you are replacing the tyres due to punctures its much better to use tyre slime in the tubes and stick with tubes otherwise ride quality will be compromised using tubeless tyres. Overall a good video though.
"how does a normal microwave heat rubber?" Well I can confirm it does. "I would recommend using a hair dryer to heat the tyre" Have you tried it? That will only heat the outside. The reason for using a microwave is to heat it from the centre. "you run the risk of the rim slipping on the tyre under power" No chance with how tight these are. "just get cheap plastic tyre levers if replacing the innertube" Nope, it's so tight even metal spoons bend. "its much better to use tyre slime in the tubes" Yeah I wish I'd thought of that before I tried to follow this video.
I think the purpose of this video is to show how to replace the tire once it has warn out. Even though the original tire in the video wasn't totally warn out yet. Also I think he just wanted solid tires cause they last longer.
Exact same issue, I used boiling water and olive oil. Also I would not use a solid tire, huge performance downgrade. I go over a few of these things here: th-cam.com/video/G3hV2LacOaw/w-d-xo.html
hello, you did not you put the valve on the front wheel? i cannot see it in the video. the valve stucked into the hole when i tried to take it off. madness to disassemble.
jozsi jozsika that vavle stem is a piece of shit I carefully used a plastic punch to get it out and good luck putting a new inner tube with a long valve stem I had to cut it with a dremmel to fit.
I was install an rear solid tire it takes me together wit my brother 2 hours wih heating in microwave,boiling etc.etc..in the end we was use heavy duty tire tools for cars until we fixed the tire correct in place.The video ist a joke to change to solid tires is not a simple thing to do!
Thank you ! You saved my life and YES I lost about 2000 calories trying to get the tire out and the new one back in (the sloid one!!) TIP ..... TIP ....... If you don't want to use the Microwave : BOIL water in a pot, turn it OFF and stick the tire in for 5 mins !!! It works !!!!
This is one of the most difficult! energy sapping things I have done! First attempt to microwave tyre caused a burnt tyre and smoke that stank the house for weeks! I changed the next tyre to a solid using hot water then both knees and 4 screw drivers! I then had a flat front tyre, more tricky as there is a wire attached. This one I did in the microwave using 30 sec blasts. I gave up a few times after spending 30 mins / 1 hour trying. Just finished the 2nd tyre. For this reason I could not recommend the scooter!
Please say how you got inner valve through the gap it is literally impossible. Had to rip the inner tube to get it off and now I'm replacing it I cannot get it through the hole I've tried for 4 hours
any tips on how to remove the valve next time i do this? i struggled with it for about to hours,saw the idea of drilling but i dont really wanna do that
Thanks I did a whole house cleanup and throw away trying to find a damn 18 wrench.. Had 3 boxes of tools and threw away enough to be left over with 1 good box of tools. Wheel is still on there tho. Some tough nut
Yeah, what were they thinking going with 18mm. Stupid, rarely used size. I have a pretty good selection of tools, but my fixed size wrenches all go from 17mm to 19mm because hardly anything uses 18mm...
@@hasansakib3969 Pretty much, yeah. I ended up needing to use an 18mm spanner. I struggled with a large adjustable crescent wrench, but it was very awkward.
Hey there, I've been struggling to get my solid tyre on my m365... I first tried heating it in water and now using the micro for 3x 1min and the tyre does indeed get softer but not like yours in the video... I am now wondering if my tyre is too small, its 14cm inner diameter, how big was yours?
Be careful with the heating part. After 2 min15 ish, I heard a noise in the microwave. the tire was already too hot and got deformed a little. Doesn't seem to be ruined. But I'd suggest heating up per 30 seconds timeframe and lower the power of the microwave. 500-750W must be enough
TekyEdits - you don't put it it in for 3 minutes all at one time. 1 minute, turn it over, another 1 minute, turn it over again. Did you not watch the video?
MrSpeedDemon72 I did exactly as mentioned as in the video man. That's why I said after the second heating up I heard a noise. Just a little warning to people if that can help 😉
I had the same issue ... 1 minute 750W ... 1 minute 750W ... 52sec 750W and the tire exploded. The second try was with hot water and it worked. I just SLOWLY boiled the tyre for 10 minutes. It needs to completely submerged and it must not touch the boiling pot.
If you have trouble to remove the bolt with the cable try this. First remove the bolt with the cable and then the other one, in the video they do the opposite but in that way it's harder to remove it!
0:50 PLEASE HELP AFAP! I got a flat tire on the front and trying to remove this stupid Screw! But it’s littery so damn tight that it’s nearly impossible to do! Its so damn hard! I use an 18 and it’s fits but it’s too tight the screw to remove it Please help me now!
This total BS. Changing the original tubed tire with a solid one. Much more difficult than indicated in this pres. Beware and do your homework before purchase of any of these scooters. Become proactive when making your choices. Solid tire makes the ride much too hard IMO!!
I put the rubber half on the opposite side of the hole, then put the tube in and asked my 6yr old son to put the valve into the hole. He made that really quick.
By the way beside heating up the tires in the microwave for 3mins, can I force both the new tire & cushion together with grease to insert back to the wheel? I don't really liked to put rubber in the microwave ya! Can you make a rear tire change vid too? Thanks ya!
David Lim I personally would use hot water to heat the tyre. Microwaves are notorious for over heating things and they are designed to heat water rather than rubber.
I've tried with hot water and it seems it's not hot enough to get the tire as soft as needed to put it in... I think micro wave is still the best option. Did anyone tried with a normal oven?
I congratulate you on your work. I found your idea of using products such as spoons and Vaseline particularly wonderful. I could not manage on my own while changing the last tire. I think I will do it this way.
Brilliant video. I watched another funny one on the same subject and am just about to change my first electric scooter tyre. Wish me luck! One obvious thing, but I thought I would mention it anyway - those of you who do try the microwave technique (I have noticed quite a few comments saying 'NO!!!') it is a slightly small error that the wording in the video says to put the wheel in the microwave. You really do NOT want to do this!!
You make it seem much easier than it is in real life just so that people use your links to buy spare parts and you get a commission. For an experienced guy it’s a pain in the butt. I think Xiaomi makes it so hard on purpose so that you buy a new one rather than repairing the old one.
Heating them in a microwave is a great way to screw up the structure of the rubber Boiling water does the job just Boil the for ten minutes and your good
My tyre has a bulge on one side. So the wheel gets trapped under the wheel guard as it turns. Any idea what is causing this? Is the inner tube bunched up on one side?
If you're watching this video because you have a flat tire, save yourself a load of time and stress and just fill the tire with "slime" and reinflate - job done!
Its not job done cause I did that and it's all gravy until the slim starts coming out. You can't do it twice plus it depends on how bad the puncture was to begin with. Not a debate just sharing what happened the weekend before I posted this response. I did get an extra 2months out of it though nice perlonged the inevitable. The war of the front wheel begins tonite and I call upon the strength 10 Gorilla's lol
Boys and girls all I can say forget the microwave and use boiling hot water in a pot, large enough to fit the tyre into, turn it a few times using any stick type of thing and finally wipe it dry quickly and you good to go for a few minutes!!! 100 % works just did it myself and unlike in the video I had to fit the inner tube too!!
@When you read the comments I will be there . I think makes it softer and expends it enough to make the process go smooth and painless..and the vaseline is quite important part though.
It looks so easy to move the bolts on the video, but on my kickbike they sit so tight they won't budge at all. Feels like no strength in the world can move them. Tips?
Does anyone know what the QR code on the front wheel is for? Reason I ask wife ran over the front wheel of scooter. Need to know if I buy a used front wheel will it work or is each wheel coded to only work on existing electronics like the dashboard or motherboard.
Wife: why does the microwave smell like burning rubber? What happened to my good spoons?
I almost had mental breakdown trying to switch these tires:) Too say it´s difficult is an understatement, Xiaomi should tell you "changing tires is an almost impossible task if you happen to have a flat".... then I went to the cycle repairshop next to me, he too almost had a mental breakdown but after a while managed to do it:)
Philip Birgersson exact same story here, at the end he said he’d Never touch another scooter😂
me too mental breakdown trying to put back the new tire
Had same thing at my bike shop 😂😂 finally replaced the front tire last night myself and I wanted to break things. Just as I got to work the front tire went flat again.. Oooo that was fun
I am going insane right now with my tire, I hate that scooter, probably I will find a bicycle shop
Did you try crying?
I curse a day when I bought this garbage. Changing tire is just a torture. I am so angry right now and my hands are all red. thanks for the video though
ben Cooper I got solid tires as well the ones you described with holes. I didn't put it yet on I am mentally not ready to go through this hell again :) In a meantime I got a new scooter falcon ZERO 10x. Its very big and heavy but much better quality, smooth ride because has suspension and I feel safer now
ben Cooper this is too accurate the valve is damn near impossible to get off and the tire is hard as a bitch to get off and my solid tire probably isn’t event gonna be able to be put on in the time frame that I have. Same thing happened to me. First the rear tire goes and I put a solid tire on that and now the front which is already a nightmare and I haven’t even boiled the tire
ben Cooper I change fI'm tire to solid as well. now its horrible I don't enjoy riding it at all. I have feel every single thing on a road :( I think it can only be an option for somebody very light weight
ben Cooper I am 94 but you are right. as long as those damn punctures won't happen again its worth it. Also you kind of get used to a less smooth ride :) Also I've noticed that experience may wary depending on type of shoes I'm wearing
Fucking hate it
Reading all these complaints, I just wanted to point out that indeed, first time is challenging AF and it took ages, but the key is not to heat up the tire or to apply a crazy amount of brute force, key is TO USE THE RIGHT TOOLS trust me!!! It looked like and odyssey without them, once I used 2 BAR CLAMPS to hold the main part in place and some metal bars for leverage to put the final part of the tire in, it became surprisingly easy!!
For the valve, if the hole is also annoying you, carefully enlarge it A BIT with a drill. Be safe though and good luck :)
I did it! It wasn't easy for sure. But it also wasn't impossible. To get the valve out, I used and allen key that was about the same size as the valve stem and tapped with a hammer. It actually went way better than expected. The real hard part was getting the tire back on. I boiled it in water and used a grease lubricant on the tire wall and on the rim. The key is having long tire irons/levers. Mine were short which mad it really hard. I ending up using one short tire lever, one regular flat head screwdriver, and the key to finishing it was a long flat bike pedal wrench. It's all about leverage. If I do this again I will definitely invest in long tire levers and maybe enlist a second set of hands to help hold the levers down (I used two hands and a foot.) Best of luck!!
In which way do you turn the key?
Hey! Usually I don't write TH-cam comments, however you literally saved me a time with a spoon usage! I spent hours trying to remove a tire, however only your method worked. Thanks a lot!
The spoon technique and microwaving the tires.. bro you’re a genius!!!!! Thank you! Thank you !🙏
Don't let the simplicity of this video trick you, it's a nightmare replacing this tire.
All the tricky parts (the most difficult parts) have been edited out from the video.
For example, He did not show how he got the air valve in/out for example. Maybe because he did not insert the inner tube. Pay attention toward the end of the video, there is no air valve in the hole.
Long story short, replacing the tire is very difficult and frustrating.
You do realise it's a solid tyre right,no need for an air valve.
And how do i pump it ? like i stuck just because i cant pump air into my tire :/
Bartłomiej in the video he is using a solid tyre,you cant pump air in it isn’t hollow it’s foam filled.
I changed it my self, itss sooo hard
Exactly, where the bloody hell is the inner tube?? I managed to do this but by the end I completely destroyed the inner tube...back to the droving board!!
THANK YOU! Vaseline and 2 minutes in the miccowave warmed the tyire up enough that I could just stake on it, jiggle about a bit and it slid right on. Having said that, I needed a dremel to cut the inner tube valve - somehow its too long to actually come out.
The person who made the scooter is probably dead by the amount of curses everyone has wished to him 💀
This is a deleted scene from the 'Saw' movies. They cut it out as it was just too much torture for any human to bear
Love that this video was no well made that no words were needed to understand every step !
Good clear video however a question? how does a normal microwave heat rubber? I would recommend using a hair dryer to heat the tyre or a conventional oven also vaseline will stay on the rim and you run the risk of the rim slipping on the tyre under power, much better to use small amount of soapy water which will evaporate and leave no residue.
Tyre levers cost less than a dollar? spoons? if people arent replacing tyres with solid tyres you run the risk of pinching the innertube using spoons, just get cheap plastic tyre levers if replacing the innertube.
If you are replacing the tyres due to punctures its much better to use tyre slime in the tubes and stick with tubes otherwise ride quality will be compromised using tubeless tyres.
Overall a good video though.
"how does a normal microwave heat rubber?"
Well I can confirm it does.
"I would recommend using a hair dryer to heat the tyre"
Have you tried it? That will only heat the outside. The reason for using a microwave is to heat it from the centre.
"you run the risk of the rim slipping on the tyre under power"
No chance with how tight these are.
"just get cheap plastic tyre levers if replacing the innertube"
Nope, it's so tight even metal spoons bend.
"its much better to use tyre slime in the tubes"
Yeah I wish I'd thought of that before I tried to follow this video.
I think the purpose of this video is to show how to replace the tire once it has warn out. Even though the original tire in the video wasn't totally warn out yet. Also I think he just wanted solid tires cause they last longer.
Where do the valve go upon mounting back?
putting it in the microwave made my house smell awful for days and ruined the the Tyre 😂😭
Exact same issue, I used boiling water and olive oil. Also I would not use a solid tire, huge performance downgrade. I go over a few of these things here: th-cam.com/video/G3hV2LacOaw/w-d-xo.html
@@drewsXR650L your link doesn't work any more :(
Same
Did it help
Just the the same 🤦🏻♂️ mine was bubbling 🔥🤣
Very clear, and appropriate as I'm replacing my flat tires with non-inflatable ones
Fairy + making the wheel hot in heated water made wonders! After struggling weeks on end, it went on a first try!
USE ALSO FAIRY!
hello, you did not you put the valve on the front wheel? i cannot see it in the video. the valve stucked into the hole when i tried to take it off. madness to disassemble.
jozsi jozsika that vavle stem is a piece of shit I carefully used a plastic punch to get it out and good luck putting a new inner tube with a long valve stem I had to cut it with a dremmel to fit.
I was install an rear solid tire it takes me together wit my brother 2 hours wih heating in microwave,boiling etc.etc..in the end we was use heavy duty tire tools for cars until we fixed the tire correct in place.The video ist a joke to change to solid tires is not a simple thing to do!
I literally ran over that tire with my car and let it under the wheel for like 5 minutes in an attempt to be able to bend it properly 😂
Thank you ! You saved my life and YES I lost about 2000 calories trying to get the tire out and the new one back in (the sloid one!!)
TIP ..... TIP .......
If you don't want to use the Microwave : BOIL water in a pot, turn it OFF and stick the tire in for 5 mins !!! It works !!!!
This is one of the most difficult! energy sapping things I have done! First attempt to microwave tyre caused a burnt tyre and smoke that stank the house for weeks! I changed the next tyre to a solid using hot water then both knees and 4 screw drivers! I then had a flat front tyre, more tricky as there is a wire attached. This one I did in the microwave using 30 sec blasts. I gave up a few times after spending 30 mins / 1 hour trying. Just finished the 2nd tyre. For this reason I could not recommend the scooter!
Lol I went through two tires and four tubes and I just did the wide tread wheels, next I'm gonna do a 10 inch wheel in front I like to suffer.
What happened at 1:38? You had the tire of at the wrong side of the rim. LOL!!
100% aquaplaning, LOL
EXACTLY! At about 1:46 some magical nonsense occurs and suddenly it's coming off the correct side!!!!? Thumbs down! 👎🏻
Nope!
He is right, otherwise you will have difficulty to remove the air stem.
What do you mean saying it's the wrong side of the rim? I mean you can get the tire off from the both sides
All these comments demonstrate I’m not alone because right now this tyre change has got me in a rage 😂😂😂
Same
Many thanks for this video. I'm sick of punctures on mine and have a honeycomb back and want to do the front. This explains it all.
cant the front wheel off-too tight, might break it if use too much force.
Same
@@bright3706 word
I had a friend step on the scooter, then I was able to turn the nut using 18mm wrench. It must've even torqued on tight.
You known what hunger is if you heat a rubber tire in the micro at 23.15 in the night. Good tutorial thou :)
Please say how you got inner valve through the gap it is literally impossible. Had to rip the inner tube to get it off and now I'm replacing it I cannot get it through the hole I've tried for 4 hours
Rose Griffths There isnt enough Space to get it trough
me too - I tried to breack the valve and make it shorter but this is not the best method! The valve is of no good now!
drill the hole on the rim bigger, it's the only way, plastic and metal
any tips on how to remove the valve next time i do this? i struggled with it for about to hours,saw the idea of drilling but i dont really wanna do that
ME too can't pump it up when put back on
A really well made and clear video. Thank you!
Thanks I did a whole house cleanup and throw away trying to find a damn 18 wrench.. Had 3 boxes of tools and threw away enough to be left over with 1 good box of tools. Wheel is still on there tho. Some tough nut
ThePotatoIsAStarchyTuberousCropFromThePerennialSolanumTuberosumOfTheNightshadeFamilyLOL hz
Yeah, what were they thinking going with 18mm. Stupid, rarely used size. I have a pretty good selection of tools, but my fixed size wrenches all go from 17mm to 19mm because hardly anything uses 18mm...
@@samgab and that is why a good set doesnt skip sizes
@@samgab i was trying to use a adjustable size or wrench but it didnt work though i fixed the size 18 mm..so is it necessary to buy a 18mm spanner?
@@hasansakib3969 Pretty much, yeah. I ended up needing to use an 18mm spanner. I struggled with a large adjustable crescent wrench, but it was very awkward.
Hey there, I've been struggling to get my solid tyre on my m365... I first tried heating it in water and now using the micro for 3x 1min and the tyre does indeed get softer but not like yours in the video... I am now wondering if my tyre is too small, its 14cm inner diameter, how big was yours?
I've also tried and I'm wondering the same thing ...
Be careful with the heating part. After 2 min15 ish, I heard a noise in the microwave. the tire was already too hot and got deformed a little. Doesn't seem to be ruined. But I'd suggest heating up per 30 seconds timeframe and lower the power of the microwave. 500-750W must be enough
TekyEdits - you don't put it it in for 3 minutes all at one time. 1 minute, turn it over, another 1 minute, turn it over again. Did you not watch the video?
MrSpeedDemon72 I did exactly as mentioned as in the video man. That's why I said after the second heating up I heard a noise. Just a little warning to people if that can help 😉
TekyEdits it could be a ghost you heard?
I had the same issue ... 1 minute 750W ... 1 minute 750W ... 52sec 750W and the tire exploded. The second try was with hot water and it worked. I just SLOWLY boiled the tyre for 10 minutes. It needs to completely submerged and it must not touch the boiling pot.
Do you have the torque specs for the rim bolts? Great vid, well done!
If you have trouble to remove the bolt with the cable try this.
First remove the bolt with the cable and then the other one, in the video they do the opposite but in that way it's harder to remove it!
Best Tip ever. Thx
Amazing video...... Loved your hand gestures😂😂😂
Did you change it with full hard tire? Becouse there is nothing about pumping the tire at the end
hard for Xiaomi to make it more complicated to change a tire or even to inflate it . The engineers time should be hang
Clearly, an idiot designed the process ...SMH
how do u inflate it
Teejay Kush oporit
Teejay Kush oporitt
Gdzie jest wentyl? Szwagier by zrobił lepiej!
I agree with every word.
koleś montuje opony bezdętkowe dlatego nie ma wentyla.
Hi
First i have thank from your video.
What range is needed for the back tire is it the same size 18 or different size?
Didnt show how to put valve in !!!
0:50 PLEASE HELP AFAP! I got a flat tire on the front and trying to remove this stupid Screw! But it’s littery so damn tight that it’s nearly impossible to do! Its so damn hard! I use an 18 and it’s fits but it’s too tight the screw to remove it
Please help me now!
It seems impossible but keep trying. I was able to finally get it after so many attempts
I use my scooter to commute. Fixing flats, 5 rear in 2 months, is a no go. A solid rear tire is a solid choice. Depends on your road conditions.
This total BS. Changing the original tubed tire with a solid one. Much more difficult than indicated in this pres. Beware and do your homework before purchase of any of these scooters. Become proactive when making your choices. Solid tire makes the ride much too hard IMO!!
I put the rubber half on the opposite side of the hole, then put the tube in and asked my 6yr old son to put the valve into the hole. He made that really quick.
By the way beside heating up the tires in the microwave for 3mins, can I force both the new tire & cushion together with grease to insert back to the wheel? I don't really liked to put rubber in the microwave ya! Can you make a rear tire change vid too? Thanks ya!
David Lim I personally would use hot water to heat the tyre. Microwaves are notorious for over heating things and they are designed to heat water rather than rubber.
I've tried with hot water and it seems it's not hot enough to get the tire as soft as needed to put it in... I think micro wave is still the best option.
Did anyone tried with a normal oven?
Nice Video ,Also made a detailed video on how to change back tyre .
1:52 how to hell did u pulled it out so quick? I needed freaking half of hour!
push that tube with screwdriver from outside. i need 2 hours to settle. lol
What can i do without microwave? Bcs i don't have it
Grazie, grazie, grazie. Non sapevo neanche da dove iniziare, grazie infinite.
I congratulate you on your work. I found your idea of using products such as spoons and Vaseline particularly wonderful. I could not manage on my own while changing the last tire. I think I will do it this way.
i need help changing rear tire. ibwas able to get thebsticker off but theres a clear hard plastic under it.
Cool, you actually used spoons as tyre spoons... :)
listen, its impossible to use plastic spoons or tyre levers on this garbage everything else breaks
hey guy, you forgot to put the air valve through the dedicated hole ;-)
How is this even possible I've been trying to get mine through for about 3 hours
@@RoseRose-mm1ed Same here, we had to remove the black plate and inside we removed a plastic valve holder that was in the way
Black Forest Spicy BBQ He didn’t, it’s a solid tire, no need for air
Hi it is required to heat the solid tires before to install it
I'm trying to change the front wheel! And... FUCK! CHANGE A TIRE OF A TRUCK IS EASIER
How did he get the tire pump up the val im stuck can't pump it up cas val too small
Do you know how to replace the folding hook when broken, could you do a video please or comment? thanks
Which hook are you refering to
where is the inside tube?
how do you get a tire pump onto that small stem valve?
Brilliant video. I watched another funny one on the same subject and am just about to change my first electric scooter tyre. Wish me luck! One obvious thing, but I thought I would mention it anyway - those of you who do try the microwave technique (I have noticed quite a few comments saying 'NO!!!') it is a slightly small error that the wording in the video says to put the wheel in the microwave. You really do NOT want to do this!!
And the tube? I see the tyre going back but no tube inside ?
I'm at the first point- removing the u shaped reflective thing on the side of the wheel which I have now broken. How the hell do you get it off???
Hot water would also work. Much safer, because you can not overheat the rubber.
Not hot enough.
How do you inflate the front tire? The stem doesn't stick out far and I can't find an adapter that works. Thanks.
Travis Faust try with the included adaptor
You can buy valve extenders at an auto parts store
@@joseurbina426 I use a 60mm extender for the rear tyre of 1000w Bullet stealth
can you write plz what the tools you use for this video.
thx
Spoon 🥄
Just tried to remove my wheel but the screws are not hex or Allen key type the hole just appear round? Any ideas
Thats some high quality spoons.😀👍
How did you put in the tyre tube pumper?
I dont understand,why front tyre do not put the tube?how come?How long the tyre hold on without pump?
You make it seem much easier than it is in real life just so that people use your links to buy spare parts and you get a commission. For an experienced guy it’s a pain in the butt. I think Xiaomi makes it so hard on purpose so that you buy a new one rather than repairing the old one.
How did you make tubeless your cars. Thank you
Nice and very informative video
Heating them in a microwave is a great way to screw up the structure of the rubber Boiling water does the job just Boil the for ten minutes and your good
You make it look so easy.
I really couldn't fit the tire inside!
I have the same problem, I tried 4 times and the tire never fit... any tips? i'm desperate
Boiling it for 10 min to 30 min Luke warm helps apparently. Took 3 hours
My tyre has a bulge on one side. So the wheel gets trapped under the wheel guard as it turns. Any idea what is causing this? Is the inner tube bunched up on one side?
how did you put back the air bulb?
If you're watching this video because you have a flat tire, save yourself a load of time and stress and just fill the tire with "slime" and reinflate - job done!
Its not job done cause I did that and it's all gravy until the slim starts coming out. You can't do it twice plus it depends on how bad the puncture was to begin with. Not a debate just sharing what happened the weekend before I posted this response. I did get an extra 2months out of it though nice perlonged the inevitable. The war of the front wheel begins tonite and I call upon the strength 10 Gorilla's lol
I didn't know I understand sign language until this video. Also (m)365th comment!
Last chapter, vibrations destroy the scooter in 400 km, battery and close mechanism
True
what size is the tyre you got ?
Second day already battling trying to the out the inner tube. The valve is too big and cant pop out. :((((
ivailokrustev same issue here :C
Did you remove the cap?
@@vapenationbg451 of course I remove the cap
I just cut the inner tube into pieces, I'm going to replace it anyways.
Did you figure this out?
Can't believe he did it with a pair of desert spoons lol 😂
Which desert? Death Valley? Gobi desert? Just checking.
Thanks for amazing guide. Spoon method doesnt work for me though. Any alternative?^^'
Thanks a lot, it helped me a lot
Didn't work for me. Heated as described but tire just will no go on, however much force is used.
This is the well done tutorial
3:20 - you missed aligning the valve with the hole in the cover.
BE VERY CAREFUL TO DO THIS!
Great video, thanks! Very very clear, good job!
excuse me but why was it so easy for you to pop the tyre on like that in youtube land? is simply isn't that easy in reality
Can confirm.
Can confirm the confirmation
Can confirm confirmed confirmation, ripped my inner rubber tyre trying to put it on, great job china, always number one in f knows what...
I can't even get the inner tube out lmao
Push bro, push
I boiled the tyre for 10 minutes and used a clamp to keep it in place. Still very hard but after some cursing I managed to get it on.
Boys and girls all I can say forget the microwave and use boiling hot water in a pot, large enough to fit the tyre into, turn it a few times using any stick type of thing and finally wipe it dry quickly and you good to go for a few minutes!!! 100 % works just did it myself and unlike in the video I had to fit the inner tube too!!
@When you read the comments I will be there . I think makes it softer and expends it enough to make the process go smooth and painless..and the vaseline is quite important part though.
It looks so easy to move the bolts on the video, but on my kickbike they sit so tight they won't budge at all. Feels like no strength in the world can move them. Tips?
You got any way later?
This was very helpful. ♥♥
The legend has it that the chosen ones ride on metal
I had a flat and I did for a while :D
it is very useful, I changed my tire with your help, thanks.
I decided not to bother with this tire changing madness and went with a scooter with split hubs. Makes tires changes a breeze.
Putting a tube back on is so fucking hard
Tube valve I’m not able to fix and put inside hole
Does anyone know what the QR code on the front wheel is for? Reason I ask wife ran over the front wheel of scooter. Need to know if I buy a used front wheel will it work or is each wheel coded to only work on existing electronics like the dashboard or motherboard.
I believe that the motors are interchangeable