I got subwoofer & amp built in combo it just comes with the clip no actual screws to screw the wires into. My question is can I just tap into the door speakers & run it to harness of the amp!?. Ty awesome video
What an excellent video! Its always nice to see the way around installing systems while working around the factory radio. Feeling completely confident to install myself!
When removing B pillar, the one right next to the seats, please remove battery cables and wait one minute ‘keep them off till the pillar is off, they are pretty tuff to pop off in most cases and the last thing you need is the AIRBAG going off, stay safe fellas
I used every exact part that this video uses and this is what ive learned. 1) the amp states it does NOT need remote 12v in the instructions. It apparently has scensors to tell itself to turn on and off based on it sensing audio. Thats a lie. U still need remote 12v run to the amp. Grab that remote from the wiring harness for the ANC delete kit. 2) you still need to use the line out converter to generate RCA input from regular speaker input in order to run RCA to the amp. 3) you also need to run a constant 12v power to the line out converter itself not just speaker inputs. Hope this helps anyone struggling. This information might have been in the video not trying to discredit the maker of the video at all. These are just little things i ran into myself.
For everyone that does not have or can not use the bypass. Just disconnect the front passenger mic, you will not have the drone noise and you will also still be able to use your mics like normal. Your welcome guys.
For those that want an Easy pre-wired bypass with LOC, click here: www.provobeast.com/product-page/2015-dodge-ram-jeep-chrysler-add-an-amplifier-t-harness
I have a factory amp but no sub and I had it where the amp would turn on and the subs worked but I had the rca cables backwards when I went to switched them it stoped working
great video....kept from tearing anything up while tearing it all apart!!! Next ?...how do/did you modify the video of real time....fast paly...real time? I have a couple videos I need to "speed up" areas???
I have a alpine 445u and I installed it like the video and it works but when I turn the truck off and turn it back on it doesn’t work and have power and everything
what’s the purpose of the wires under driver seat. Asking because my 2020 came with a subwoofer installed but not working. I looked under the driver seat and I don’t see that contraption in there
I got the ANC-Ch01 and the loc pac lpc7 -2 . Used T-tape to connect everything. Got power to my amp tested it got 12v but got 0 volts on remote turn on. Amps not turning on
I have double checked everything. Plugged in lp7-2 the light comes on but I do not get 12 volts to speaker outputs. I tied into the front two speakers. The white and gray just to keep the wires color coded the same.
Does this apply to the ones with 12inch factory screen? My 2020 Ram came with installed subwoofer but somehow all lights are on but isn’t working.. The color wire hooked for signal are black and white?
So what does the amp poc 4 ch41 do is that only if adding a amp for all door speakers. I’m replacing all of them and adding two subs all with a 5 channel amp do I need that?
I’ve been running for months with the ANC completely bypassed and not powered. There’s another harness that is just a speaker bypass. The V6 trucks use the same 8.4 without an ANC. The truck doesn’t know. 2019 Rebel Hemi no amp.
Anywhere near the amp on a solid ground. For example i drilled and tapped part of the rear seat frame and sanded down the paint in order to get a good ground connection.
If you have alpine setup. What do you do to add subs. Does any one know of a video. And do you loose any capabilities. Like mics. When hooking up with. The bypass harness
4 gauge was tight, so 1/0 would be more difficult. Never say never, give it a shot. Worst case scenario you can go under carpet under along the frame rail.
Ok I just installed my system today and I tapped into the rear speakers of the anc bypass harness do you know if doing that is going to be any difference then tapping in to front speakers
Would you be able to do a video on how to modified the bypass to accept the PAC so you don’t have to pull apart the pillar? I have ordered everything you mentioned just want to see how you would go about it! Thanks!
ground loop noise is usually from poor quality RCA cables and bad grounds. If you are using quality cables and your ground doesn't have any resistance, you should be fine.
I just installed my pac bypass and it made my speaker volume go down and when its not installed my speakers are much louder have you had this issue its a 2020 ram 1500 6 speaker base speaker system@ProvoBeastAudio
Great video! I'm seriously thinking of adding a sub to my 2021 Ram 1500. I've been reading and trying to decide between a single 12" or a single 10" sub woofer. I'm having a hard time deciding. Any thoughts or suggestions? I like the Pionner amp you recommend. Also, what is your recommendation on a ported box vs a sealed box? Again great video!!
What would you recommend for the 19 speaker Harmon kardon system? I’m looking for something that’s gonna give me some clear sound but also hits good 10 or 12 inch sub
Our amplifier generated that for us via DC offset. If you follow my suggestion on the type of line out converter tapped into the ANC bypass harness stated in the video, then the pac loc will generate your remote turn on wire for you.
Yes, but different parts are required. If just an amp / sub install, you'll need either the amp pro by pac, or will have to tap into the OEM sub for signal.
@@jeremyschott5782 Using the Pac LOC i recommend in the description and video provides the remote turn on for you as it generates it for your amplifier.
Yes, if you have the Harmarn Kardon audio system, the cheap way would be to tap into the signal to the factory sub, or alternatively, use the Pac APSUB-CH41 which gives you a perfect signal output from the factory radio for an aftermarket amplifier: ebay.us/zROV2b
SO with 2020 ram 1500 with basic non amplified or subwoofer. I can jus use the lc2i pro to get my signal for my rca to my aftermarket amp? Seen people always use the pac amp pro in the 5th gen rams but didn't see why I couldn't jus use the lc2i instead of that pac pro. Is that because they have factory amp and sub?
The amp pro generally is used when the truck is equipped with the factory amplified audio system. Sometimes not, but it's more common when bypass the premium system from the factory.
I recently installed this harness in my 2020 Ram 1500 Sport when I plugged in the harness the humming went away however my amplifier does not turn off with the truck now .. any suggestions on how to resolve this !! Thanks !
So I have a 2022 ram can I cut that anc Bypass send the side that has signal to a lc7 and the other side send back to the speakers run speed wire to it from the amp to amplify my speakers ?
It was hard to tell but was this install on a RAM with the Crew Cab or Quad Cab. Trying to get some subwoofer and amp ideas for Quad Cab, but have limited space. Thanks
wired mine the exact same way but for some reason I'm hearing engine noise and exhaust noise coming from subs when truck is running. do you know the problem?
I'm waiting to add subs and amp in my 2020 ram 1500. I can jus use a lc2i pro to get my rca signal and not use the pac pro? I jus have standard sound system no amplified or factory sub.
@Provo Beast Audio Installation I have a 2020 ram 1500, if I mount my lc2i under my driver seat next to my ANC module, how long of rca cables you think I will need? Was gonna mount my amp where you mounted this amp in video or on other side. Was thinking maybe 9ft rca or you think I should get 12ft? Thanks
@@johnnypiper1717 Good question, I'd get yourself a good length of string, and mock up how much length you are going to need, measure that, and purchase that correct length. measure twice, buy once!
thank you. i did the same method (using harness from PAC), and use the hi-level input on my Alpine amp- but there is a small issue: after my truck (2023 ram) powers down, about 15 seconds later I get a thump from the sub as the amp powers itself down. it also thumps if i get into the truck and dont start the ignition after several seconds. A time delay issue Im guessing. Any recommendations?
@@justinschafer118 good morning! I did get the issue resolved: using the lc2i helped by lowering the intensity of how much thump came from the sub speaker when the vehicle powered down. It was tolerable but still not ideal since it was still doing it, although much quieter. Had I used the relay switch power-on option for the lc21, and not source input power-on, I think that would have fixed it as well. I ended up going back and using the pac amp pro made for my Dodge radio and used its relay switch option, and that ultimately fixed the issue completely. Definitely a timing issue that needed a relay switch to power the amp on at the right time.
2019 Ram Bighotn - Can anyone help me figure out how to get a solid ground point. I have not been able to locate one at all. Tried creating one on the for under back seat, can't get a good ground
Greetings, I am interested in installing a amplifier that can amplify the six speakers and the sub woofer. Would I have to buy something additional? I appreciate any suggestion.
Yes, generally a 5 channel amplifier would do, depending on what speaker types you are amplifying. We can assist you more if you send us a message on facebook.
To use the LOC, in the picture in the video it shows to use the black and yellow wires to connect to the ANC wires which is fine. But then it says to use the white and grey sets to connect to the ANC but there are only 4 usable wires on the LOC, two of which were the black and yellow, and one of which is the blue output to the remote (I’m guessing). Which wires are we supposed to use to tap into the white and grey sets?
Alpine system generally doesn't have ANC, but always good to double check. In 2019 + 1500 trucks, it's under the driver front seat, and 2019 + 2500 or 3500 trucks, it's under the driver side dash. If the module isn''t there, then you don't have ANC.
We didn't as our amp had a built in LOC. We recommend installing the Pac LP7-2 where you install your ANC bypass harness and just tap into the speaker wire in the ANC harness for signal.
So if you install it this way on the pac lp7-2 you should only be using front speaker wires and the yellow for power and the black for ground ? And don’t need to run the remote blue ? Also on the anc itself only one connection is plugged into it with the bypass harness ?????
Amp will remain on until the vehicle "goes to sleep". Generally shuts down with there DC offset no longer puts out current over the speaker wiring. Can take up to 5 min
@@ProvoBeastAudio That’s just it, it never goes to sleep there is always power. I video taped the amp on for around 20 minutes and it never shut down. I did exactly what’s on your video but through the ANC bypass.Any additional information or research would be appreciated. It’s driving me nuts.
@@ProvoBeastAudio I will reinstall it. Should I connect the remote from amp to the pac or to a keyed power. Are you able to respond on FB messenger. I sent a message through there also.
@@ProvoBeastAudio will the pac shut off the amp? I was second guessing that be last week my battery went dead/bad and had to replace it. So when I got the truck back I started researching and saw there was always a draw from the speakers. Also John Lance from Ram AlfaOBD confirmed that there is always power draw thru the speakers.
I followed all the steps everything worked for about a month now I’m having some issues. I tried re buying everything in the links provided that I needed thinking something was just bad. For some reason I’m not getting the power out of my subs that I was before. It’s almost like the subs are getting the same low power that my door speakers are getting. I know it’s not the amp and it’s not the RCA cables because I tested with new RCA’s and a different amp. Anybody having this issue or maybe have a solution? Probably just my sh*tty luck Lol
I’ve been running for months with the ANC completely bypassed and not powered. There’s another harness that is just a speaker bypass. The V6 trucks use the same 8.4 without an ANC. The truck doesn’t know. 2019 Rebel Hemi no amp.
Parts used linked in the description of the video!
Is there anyway i can contact you to ask you some questions about my ideal setup for my truck?
I got subwoofer & amp built in combo it just comes with the clip no actual screws to screw the wires into. My question is can I just tap into the door speakers & run it to harness of the amp!?. Ty awesome video
The most in-depth video I've ever seen on a stereo system install.
What an excellent video! Its always nice to see the way around installing systems while working around the factory radio. Feeling completely confident to install myself!
When removing B pillar, the one right next to the seats, please remove battery cables and wait one minute ‘keep them off till the pillar is off, they are pretty tuff to pop off in most cases and the last thing you need is the AIRBAG going off, stay safe fellas
Best video I have seen on these trucks yet
I used every exact part that this video uses and this is what ive learned.
1) the amp states it does NOT need remote 12v in the instructions. It apparently has scensors to tell itself to turn on and off based on it sensing audio. Thats a lie. U still need remote 12v run to the amp. Grab that remote from the wiring harness for the ANC delete kit.
2) you still need to use the line out converter to generate RCA input from regular speaker input in order to run RCA to the amp.
3) you also need to run a constant 12v power to the line out converter itself not just speaker inputs.
Hope this helps anyone struggling.
This information might have been in the video not trying to discredit the maker of the video at all. These are just little things i ran into myself.
BEST VIDEO!!!! Explained everything i needed to know!!!! I dont comment alot but this video helped me FOR SURE!!!
For everyone that does not have or can not use the bypass. Just disconnect the front passenger mic, you will not have the drone noise and you will also still be able to use your mics like normal. Your welcome guys.
how do I know if i cannot use the bypass?
Where is the front passenger mic located
For those that want an Easy pre-wired bypass with LOC, click here: www.provobeast.com/product-page/2015-dodge-ram-jeep-chrysler-add-an-amplifier-t-harness
Good morning I am thankful that you made a video , simple procedure. I can’t wait to do mine 2021Ram (q-c) tradesman
Did you end up having issues with the RCA ports?
Feeling inspired to hook up 15s in my truck now 😂
Can you do a video on how to wire the pac line out converter to the ANC wire harness please
Yeah really would like to know!
That would be awesome
www.provobeast.com/product-page/2015-dodge-ram-jeep-chrysler-add-an-amplifier-t-harness
I got the same harness your using and the black connector part doesn’t fit right and when I fit it in the rear speakers don’t work
¡Gracias!
This video is exactly what I needed! Thanks
I have a factory amp but no sub and I had it where the amp would turn on and the subs worked but I had the rca cables backwards when I went to switched them it stoped working
Sir you are a life saver thank you
great video....kept from tearing anything up while tearing it all apart!!!
Next ?...how do/did you modify the video of real time....fast paly...real time? I have a couple videos I need to "speed up" areas???
we use FCPX to edit our content.
I have to same set up but I can’t get my sub box to fit I have a 2020 ram sport crew cab and the same sub box
I have a alpine 445u and I installed it like the video and it works but when I turn the truck off and turn it back on it doesn’t work and have power and everything
Which tonuse if its amplified for the ANC BYPASS
I have a 2010 Ram 2500’ with a factory alpine system with a factory sub. Am I able to tap into the existing sub wiring to tie the loc into?
I'm stumped, 2020 classic with no factory amp or anc module under the drivers seat. Where can i tap into for stereo sound to loc????
what’s the purpose of the wires under driver seat. Asking because my 2020 came with a subwoofer installed but not working. I looked under the driver seat and I don’t see that contraption in there
From what I’ve been researching it’s what by passes the ANC in all 5th gen rams and also gets you your audio input to the amp
I got the ANC-Ch01 and the loc pac lpc7 -2 . Used T-tape to connect everything. Got power to my amp tested it got 12v but got 0 volts on remote turn on. Amps not turning on
Double check that u have constant 12v at the loc pac lpc7. That needs constant 12v to work properly
I have double checked everything. Plugged in lp7-2 the light comes on but I do not get 12 volts to speaker outputs. I tied into the front two speakers. The white and gray just to keep the wires color coded the same.
Does this apply to the ones with 12inch factory screen? My 2020 Ram came with installed subwoofer but somehow all lights are on but isn’t working.. The color wire hooked for signal are black and white?
Will the 2x 12inch 4ohm subs you recommend work with the mono amp you are using?
So what does the amp poc 4 ch41 do is that only if adding a amp for all door speakers. I’m replacing all of them and adding two subs all with a 5 channel amp do I need that?
Do a 5-channel install on 2016 Kia optima EX. Without Harman system but has navigation.
We would whenever we get one in the shop.
What should I get if I have the Harmon & Kardon system
Do you need the Blue and Brown wire from the ANC bypass and LOC. I tapped every thing else in
How did this work out for you?
I’ve been running for months with the ANC completely bypassed and not powered. There’s another harness that is just a speaker bypass. The V6 trucks use the same 8.4 without an ANC. The truck doesn’t know. 2019 Rebel Hemi no amp.
I'm in vernal utah can I come out to have you install some slapps in my ram rebel
I have two JL tw513 on a ford and need them on a dodge ram 2019. Have any info on where I can get a box for those ?
Where did you ground your negative wire?
Anywhere near the amp on a solid ground. For example i drilled and tapped part of the rear seat frame and sanded down the paint in order to get a good ground connection.
I have a 2024 ram 2500 big horn with a factory rear subwoofer how would I got about putting in an aftermarket amp and subwoofer kit?
If you have alpine setup. What do you do to add subs. Does any one know of a video. And do you loose any capabilities. Like mics. When hooking up with. The bypass harness
Can you fit a 1/0 run in the factory channel inside the cab? Thanks. Great vid
4 gauge was tight, so 1/0 would be more difficult. Never say never, give it a shot. Worst case scenario you can go under carpet under along the frame rail.
I did everything the same way and some time it doesn’t turn on check the ground re check all the connections any idea on what it can be
Run a seperate remote wire. I had that issue using the exact same setup as the vid
Is it better to tap the pac into the front or rear speakers on the harness
without putting a RTA on to test, generally id do the front speakers.
Ok I just installed my system today and I tapped into the rear speakers of the anc bypass harness do you know if doing that is going to be any difference then tapping in to front speakers
Would you be able to do a video on how to modified the bypass to accept the PAC so you don’t have to pull apart the pillar? I have ordered everything you mentioned just want to see how you would go about it! Thanks!
That is all you’ll need to disable the ANC on the alpine system. Took 10s to do
www.provobeast.com/product-page/2015-dodge-ram-jeep-chrysler-add-an-amplifier-t-harness
If i use the ANC and pac install way would running rca next to power wire on driver side cause interference noise rca with power wire
ground loop noise is usually from poor quality RCA cables and bad grounds. If you are using quality cables and your ground doesn't have any resistance, you should be fine.
I just installed my pac bypass and it made my speaker volume go down and when its not installed my speakers are much louder have you had this issue its a 2020 ram 1500 6 speaker base speaker system@ProvoBeastAudio
Can u please do a video showing how to connect bypass to the pac E72
www.provobeast.com/product-page/2015-dodge-ram-jeep-chrysler-add-an-amplifier-t-harness
Why didn’t you pull the rear speakers signal from the black 16 pin from the ANC-CH01 harness instead of opening up the pillar?
He explained it in the video.
Great video! I'm seriously thinking of adding a sub to my 2021 Ram 1500. I've been reading and trying to decide between a single 12" or a single 10" sub woofer. I'm having a hard time deciding. Any thoughts or suggestions? I like the Pionner amp you recommend. Also, what is your recommendation on a ported box vs a sealed box? Again great video!!
What would you recommend for the 19 speaker Harmon kardon system? I’m looking for something that’s gonna give me some clear sound but also hits good 10 or 12 inch sub
4 6.5s for loudest possible, I prefer 2 8s. Underseat ported, subs facing forward with subwoofer grills.
Where did you get source for the remote wire?
Our amplifier generated that for us via DC offset. If you follow my suggestion on the type of line out converter tapped into the ANC bypass harness stated in the video, then the pac loc will generate your remote turn on wire for you.
Could you use the same equipment if the truck did have the HK upgraded stereo package?
Yes, but different parts are required. If just an amp / sub install, you'll need either the amp pro by pac, or will have to tap into the OEM sub for signal.
So if you wanted to splice into the ANC bypass are the wires color coded the same and is that where you would tie in your line out converter.
Yep you got it!
How would you wire the remote turn on? Can you wire that to the ANC module somehow?
@@jeremyschott5782 Using the Pac LOC i recommend in the description and video provides the remote turn on for you as it generates it for your amplifier.
@@ProvoBeastAudio I have it figured out now. Never have done an install before. Thanks for all your help
@@jeremyschott5782 what truck do you have?
I connected to the Yellow for the remote and it's always on. Is there another wire for key on?
Yellow is constant 12v u need remote 12v which is the blue. Double check the wiring diagram that came with the equipment u purchased. Hope this helps
These parts and install method will work for my 2023 Ram?
As long as you have the same trim without the factory alpine audio system, yes.
You think the speaker wire from the stock HK subwoofer would be a good line out for RCA hook up?
Yes, if you have the Harmarn Kardon audio system, the cheap way would be to tap into the signal to the factory sub, or alternatively, use the Pac APSUB-CH41 which gives you a perfect signal output from the factory radio for an aftermarket amplifier: ebay.us/zROV2b
So what adapter should you use for the harmon kardon sound system?
I just spliced into the b pillar wires cheaper that buying a adapter
SO with 2020 ram 1500 with basic non amplified or subwoofer. I can jus use the lc2i pro to get my signal for my rca to my aftermarket amp? Seen people always use the pac amp pro in the 5th gen rams but didn't see why I couldn't jus use the lc2i instead of that pac pro. Is that because they have factory amp and sub?
The amp pro generally is used when the truck is equipped with the factory amplified audio system. Sometimes not, but it's more common when bypass the premium system from the factory.
Is is possible to tap into the wires from the anc harness since they are already exposed and save the time from the pillar removal?
and just realized in minute 13, you addressed this 😁
I recently installed this harness in my 2020 Ram 1500 Sport when I plugged in the harness the humming went away however my amplifier does not turn off with the truck now .. any suggestions on how to resolve this !! Thanks !
Did you tapped into the yellow wire on the ANC bypass harness, the amp will stay powered on.
So I have a 2022 ram can I cut that anc Bypass send the side that has signal to a lc7 and the other side send back to the speakers run speed wire to it from the amp to amplify my speakers ?
Sure!
Do I have to disconnect the battery to install the anc module or no.
I would
What color is the factory Amp wire?
It was hard to tell but was this install on a RAM with the Crew Cab or Quad Cab. Trying to get some subwoofer and amp ideas for Quad Cab, but have limited space. Thanks
Rebels are crew can only I believe
wired mine the exact same way but for some reason I'm hearing engine noise and exhaust noise coming from subs when truck is running. do you know the problem?
You need to install the ANC bypass harness shown in the video. Linked in description as well.
I'm waiting to add subs and amp in my 2020 ram 1500. I can jus use a lc2i pro to get my rca signal and not use the pac pro? I jus have standard sound system no amplified or factory sub.
Any line out converter will be fine, yes. And simply tap into the speaker wire in the ANC bypass harness for a easy and simple install.
@Provo Beast Audio Installation I have a 2020 ram 1500, if I mount my lc2i under my driver seat next to my ANC module, how long of rca cables you think I will need? Was gonna mount my amp where you mounted this amp in video or on other side. Was thinking maybe 9ft rca or you think I should get 12ft? Thanks
@@johnnypiper1717 Good question, I'd get yourself a good length of string, and mock up how much length you are going to need, measure that, and purchase that correct length. measure twice, buy once!
@Provo Beast Audio Installation that's what I'll do, you think the rca cable should be ran on separate side than my 0g power wire? Thanks for the help
@@johnnypiper1717 if at all possible, ALWAYS run power on one side, signal on the other.
Do you know if the 12 inch screen has the input for subwoofer?
99% of factory radios will not have a RCA preout for a subwoofer.
It will work this with 2022 ram bighorn Cummings with unconnect 5?
If you have the same connections we do, then yes.
My 2019 ram 1500 has a amp under the seat but I can't find a subwoofer. What system do I have?is that the bare minimum system?
It may not be an amp, it may be the ANC module
thank you. i did the same method (using harness from PAC), and use the hi-level input on my Alpine amp- but there is a small issue: after my truck (2023 ram) powers down, about 15 seconds later I get a thump from the sub as the amp powers itself down. it also thumps if i get into the truck and dont start the ignition after several seconds. A time delay issue Im guessing. Any recommendations?
It may be a high-level input issue. You could try using a line out converter to see if that helps or using the Audio Control LC1i or LC2i Pro.
@@ProvoBeastAudio thank you - i purchased the lc2i pro and will install it after the weekend. Much appreciated !
@@seansean8008did you ever get your thump issue resolved?
@@justinschafer118 good morning! I did get the issue resolved: using the lc2i helped by lowering the intensity of how much thump came from the sub speaker when the vehicle powered down. It was tolerable but still not ideal since it was still doing it, although much quieter. Had I used the relay switch power-on option for the lc21, and not source input power-on, I think that would have fixed it as well.
I ended up going back and using the pac amp pro made for my Dodge radio and used its relay switch option, and that ultimately fixed the issue completely. Definitely a timing issue that needed a relay switch to power the amp on at the right time.
@@seansean8008 awesome. Thank you for the advice and help
2019 Ram Bighotn - Can anyone help me figure out how to get a solid ground point. I have not been able to locate one at all. Tried creating one on the for under back seat, can't get a good ground
You have to make one
I drilled a hole for a bolt lol this guy in the vid did too
this ANC will will work for either the Alpine system or the HK system correct ?
Generally the factory amplified audio system doesn't have ANC.
Greetings, I am interested in installing a amplifier that can amplify the six speakers and the sub woofer. Would I have to buy something additional? I appreciate any suggestion.
Yes, generally a 5 channel amplifier would do, depending on what speaker types you are amplifying. We can assist you more if you send us a message on facebook.
To use the LOC, in the picture in the video it shows to use the black and yellow wires to connect to the ANC wires which is fine. But then it says to use the white and grey sets to connect to the ANC but there are only 4 usable wires on the LOC, two of which were the black and yellow, and one of which is the blue output to the remote (I’m guessing).
Which wires are we supposed to use to tap into the white and grey sets?
www.provobeast.com/product-page/2015-dodge-ram-jeep-chrysler-add-an-amplifier-t-harness
How do you bypass the anc in models with the alpine system?
Alpine system generally doesn't have ANC, but always good to double check. In 2019 + 1500 trucks, it's under the driver front seat, and 2019 + 2500 or 3500 trucks, it's under the driver side dash. If the module isn''t there, then you don't have ANC.
I’m so confused why rca was stripped and connected to speaker wire
It's a high level input cable provided by the Pioneer amplifier. If your amplifier doesn't have a high level input option, use a line out converter.
Where did you guys install the pac7?
We didn't as our amp had a built in LOC. We recommend installing the Pac LP7-2 where you install your ANC bypass harness and just tap into the speaker wire in the ANC harness for signal.
So if you install it this way on the pac lp7-2 you should only be using front speaker wires and the yellow for power and the black for ground ? And don’t need to run the remote blue ? Also on the anc itself only one connection is plugged into it with the bypass harness ?????
Did you happen to notice the amp was still powered up after the truck was shut off and locked and all?
Amp will remain on until the vehicle "goes to sleep". Generally shuts down with there DC offset no longer puts out current over the speaker wiring. Can take up to 5 min
@@ProvoBeastAudio That’s just it, it never goes to sleep there is always power. I video taped the amp on for around 20 minutes and it never shut down. I did exactly what’s on your video but through the ANC bypass.Any additional information or research would be appreciated. It’s driving me nuts.
@@Luis-kk8kp Add a Pac LP7-2 and skip the high level signal input. Use that LOC and tap into the ANC bypass. That should fix your issue.
@@ProvoBeastAudio I will reinstall it. Should I connect the remote from amp to the pac or to a keyed power. Are you able to respond on FB messenger. I sent a message through there also.
@@ProvoBeastAudio will the pac shut off the amp? I was second guessing that be last week my battery went dead/bad and had to replace it. So when I got the truck back I started researching and saw there was always a draw from the speakers. Also John Lance from Ram AlfaOBD confirmed that there is always power draw thru the speakers.
Where can I get wire ferruls from?
We get ours on amazon
Bypass does not work on 2023 ram big horn
For some reason my truck doesnt have the ANC under the drivers seat and I am completely lost
Mines doesn't neither did you find where it's located?
I followed all the steps everything worked for about a month now I’m having some issues. I tried re buying everything in the links provided that I needed thinking something was just bad. For some reason I’m not getting the power out of my subs that I was before. It’s almost like the subs are getting the same low power that my door speakers are getting. I know it’s not the amp and it’s not the RCA cables because I tested with new RCA’s and a different amp. Anybody having this issue or maybe have a solution? Probably just my sh*tty luck Lol
any fix? got the same issue
Now try putting the seat down
🤡🤡🤡
Will this set up in any way make me loose my rear camera?
Nope
@@ProvoBeastAudio with that harness can I hook up two amps thru it or how would I go about doing so?
What should I get if I have the Harmon & Kardon system
I’ve been running for months with the ANC completely bypassed and not powered. There’s another harness that is just a speaker bypass. The V6 trucks use the same 8.4 without an ANC. The truck doesn’t know. 2019 Rebel Hemi no amp.
If i don't have that pioneer what wire would be used for a remote from the factory amp on a hk system?