Love your setup mate, I've been building my 2023 500 up and have put on a lot of the same parts as you. 😄 Also, I actually contacted HDB about the anodized guards, and it turns out they do actually do them in black, but they're limited and cost you an extra $50.
Hi Keith - nice video - I have the flexx bars on my bike - any idea if I cud make those handguards work with them? - and have you tried the flexx bars? - if yes what do you think of them? - finally what are your thoughts on steering dampers (Scott's or the like)? - I see you have everything except that...thanks mate
Hey Keith, LOVE the content - THANK YOU!! I’m curious, on the motominded mount how did you guys get the hole for the heat demons grips?? Did you just drill a bigger hole where there was a little one? I’d like to get a set up like this - any help appreciated!!
@@keithjob So sorry I meant on your bros bike, looks like he has the MotoMinded plate and maybe drilled out a hole a bit bigger in the middle to accommodate for the HD switch??
maybe, but the cables run through a channel kind of down through the mask where they are now. You would need to completely reroute them and I think they would possibly foul and catch on other things.
Hi Keith. You could reroute your cables to run from left to right side just below your headlight. That way they would not be rubbing your windscreen. You can check this solution on the website of The Rolling Hobo. It is common on rally bikes and leaves a ’clean cockpit’. I plan to implement it on my coming bike. Thank you for your excellent videos!
I try to avoid tapping into OEM wires 🤨 so I ran a fused feed from battery to front, then run the 12v socket off that. And two GPS power feeds. And the heated grips. 😎
I just got the Enduro windscreen for my 2013 KTMEXCF and for the life of me I cannot figure out how the mounting brackets mount to the bike I have the two top poles attached to the bracket for the other end I’m not sure if they go to the signal light or somewhere else or which hole the bracket uses because it has two holes any ideas or suggestions or possible video on how it hooks up?
Mine went to the hole that bolts to the supermount. However in their instructions they have you drill a hole through the plastic just above the rubber strap mounting slot. The install instruction sheet I got is linked below: drive.google.com/file/d/1ir3se3AlFBAcCf2jk8pnnNwONTPexv_U/view?usp=sharing
Top Screens the BajaWorx Been using one now on my custom built 1290 Super Enduro with the BajaDesign XL80 KTM EXC 2019 light fairing Night riding i use Duel BajaDesign LP9's & BajaDesign Onix6 10" bar was big job wiring up all 4 x features on LP9 & fooling the CanBus system Was early stage setup - Since refined all switching at thumb reach th-cam.com/video/nwAJd-kmweM/w-d-xo.html
Thanks for this video I have been having the same issue with finding a screen that can work around the brake lines.
Any suggestions on dealing with the Bajaworx screen hitting/resting on my hand guard mounts?
Love your setup mate, I've been building my 2023 500 up and have put on a lot of the same parts as you. 😄
Also, I actually contacted HDB about the anodized guards, and it turns out they do actually do them in black, but they're limited and cost you an extra $50.
Black definitely looks better 😎
Hi Keith - nice video - I have the flexx bars on my bike - any idea if I cud make those handguards work with them? - and have you tried the flexx bars? - if yes what do you think of them? - finally what are your thoughts on steering dampers (Scott's or the like)? - I see you have everything except that...thanks mate
Great video. How many Kms and hours have the bikes done have you had todo any rebuild or major maintenance on them?
Hey Keith, LOVE the content - THANK YOU!! I’m curious, on the motominded mount how did you guys get the hole for the heat demons grips?? Did you just drill a bigger hole where there was a little one? I’d like to get a set up like this - any help appreciated!!
For the switch? I made my own plate out of some acrylic and cut the holes I wanted. 😎
@@keithjob So sorry I meant on your bros bike, looks like he has the MotoMinded plate and maybe drilled out a hole a bit bigger in the middle to accommodate for the HD switch??
What if you routed your brake hose and cable behind the mask? Do you think that would save the windscreen from getting all marked up?
maybe, but the cables run through a channel kind of down through the mask where they are now. You would need to completely reroute them and I think they would possibly foul and catch on other things.
Hi Keith. You could reroute your cables to run from left to right side just below your headlight. That way they would not be rubbing your windscreen. You can check this solution on the website of The Rolling Hobo. It is common on rally bikes and leaves a ’clean cockpit’. I plan to implement it on my coming bike. Thank you for your excellent videos!
Very nice i must say, But im sure i noticed a Oled screen on your bars is that for your tires ?
yes TPMS. My review is here: th-cam.com/video/chsjlTI3wag/w-d-xo.html
On what wires did you tap your 12 volt marine charger port that is on your highway dirt bike mount?
I try to avoid tapping into OEM wires 🤨 so I ran a fused feed from battery to front, then run the 12v socket off that. And two GPS power feeds. And the heated grips. 😎
I just got the Enduro windscreen for my 2013 KTMEXCF and for the life of me I cannot figure out how the mounting brackets mount to the bike I have the two top poles attached to the bracket for the other end I’m not sure if they go to the signal light or somewhere else or which hole the bracket uses because it has two holes any ideas or suggestions or possible video on how it hooks up?
Mine went to the hole that bolts to the supermount. However in their instructions they have you drill a hole through the plastic just above the rubber strap mounting slot. The install instruction sheet I got is linked below: drive.google.com/file/d/1ir3se3AlFBAcCf2jk8pnnNwONTPexv_U/view?usp=sharing
Did you have the upholster use the original seat base. Just thinking if I want to have one made that I would have to send in seat. How much $
Yeah I gave him the whole seat. $ can't remember but it was waaaay less than a genuine Fisher or SC. Maybe less than $200? Don't quote me.😬
Thanks
Hi Keith, great videos..
As a Canadian I suffer ridiculous duty fees getting these American products up here.
Do you have this problem in Canada?
Importing these to Australia, yes we pay a lot for postage.
Top Screens the BajaWorx
Been using one now on my custom built 1290 Super Enduro with the BajaDesign XL80 KTM EXC 2019 light fairing
Night riding i use Duel BajaDesign LP9's & BajaDesign Onix6 10" bar
was big job wiring up all 4 x features on LP9 & fooling the CanBus system
Was early stage setup - Since refined all switching at thumb reach
th-cam.com/video/nwAJd-kmweM/w-d-xo.html
Those mirrors are useless