Sleeping in a tent and 10 hours from home. Now that’s a hell of a field repairman. Props to you guys! Not many people out there now a days with the grit and will to do this kind of stuff. Good to see it still alive 🤙🏼🤙🏼
Most people don't understand the art of firefighting, just controlling the fire hose takes a skill or it is dangerous. You are right though the mechanics of maintaining the pressure at the nozzle is very important. Just the design of the nozzle is critical to the success of the team fighting the fire. B.C.
@@4thgradedropout980 I'm pretty sure they are double row cylindrical Roller bearings. So the inner race can pivot inside the outer race. Not a regular Roller bearing
A little tip I learned in the field with a bearing race inside an axle housing that was an interference fit and it had spun and stuck tight with no way to get behind it to knock or pull it out. Out of desperation, I went home and got a can of air duster, turned it upside down and sprayed the race until it was frozen and had shrunk enough to be pulled it out by hand. After that, I always keep a couple of cans in the shop and in my truck.
I didn’t see any grease in those old bearings. I would think to see some residue but they looked completely dry. Probably why they failed. Gotta keep that stuff lubed. Good job with that in not ideal conditions.
Man, your content never disappoints, from simple tanks welds in your shop to taking apart, diagnosing and fixing heavy equipment out in the boonies. Especially with your cool and collected demeanor and knowledge a young buck or not so young person can sure learn a LOT from you!
That's the best way to support the firefighters, with equipment that's repairable in the field, so that they can make best use of it and it can put back into action if it breaks. Not to forget of the guys like you, that drive 10hrs away from home, sleeping in tents and give their best to keep that stuff up and running. Thx for showing and for helping to save lives as well! 👍👍👍
Great job! You are lucky to have good customers and the support from them and the parts suppliers. 20hrs away is not where you want to have the wrong parts.
We own homes in both Siskiyou and Sonoma counties; both areas close to my homes have been ravaged by the fires over the past 5 years. Happy Camp is west of my house; it’s far enough away but we’ve seen enough fire out here to last a lifetime. It’s a team effort to keep the area safe. I want to personally thank you for being part of that team 🇺🇸
Greg, 1:15 , man, when you snap a Snap-On hex driver, you are really having to torque it.... I had that issue on galvanized set screws in aluminum on a boat I took to the coast.... 2 days later, they were hosed just like this..... I know you have probably used or seen, but the hand held non powered impact drivers you hit with a hammer are really good at getting hex, Phillips and Torx and slotted screws out in these situations.....I bought one when I started out in 1973 because I could not afford an air tool and had no compressor.....well I used for a short time, and never used again until 2008.....and found it was super useful.....of course, I had been using air tools and thought it was not needed.... that slam/impact of the tool into the screw and your wrist turning gives a much better bite than an electric or air tool.......I learned this working on Motorcycles and pulleys on industrial gear ....I hope this tidbit can help someone out there.....cheers, Paul p.s. my impact was made by Snap-On that I bought in 1973......and the drivers I twisted on the boat were Snap-On from 1973...but when I used with the Hand Impact....the set screws came out.....Snap-On Rules !!!
I've seen guys with electric grease guns push the seals out of bearings on a mulcher head like that. Then it cant hold its grease and gets debris in the bearing and it fails early. I couldn't believe it either. It was about the only time i ever heard of something getting too much grease
Yeah i hope they put in some grease between the clips shown or that thing will be in pieces in a few days. Assembly without lube is not that unsual if you have to heat the bearing tho.
Well done young man. Looked a nasty task but you got it done. I refused welding work in London last year. Its about four hours south of me. The money was OK, but London is a nasty, expensive and unpleasant place. You're customer is obviously worth working for and he obviously values you too!
Great video, thank you for sharing it. I didn’t realize that you travel north for work too. I’ve got a 12-16 hour job for you in Yuba County if you’re interested on the way back. It’s on a case 450 dozer.
I've used a die grinder before to get those rollers out. Just make a pocket and move them one by one to it and pull them out. But I had to save the shaft and it was quite time consuming.
Hmmm, I'm slipping, I missed this one when it came out. Those mulchers are horrific. I've seen them on skid steers also. It is amazing the bearings can stand the hammering that goes with the job.
Amazon has a huge hydraulic 3 jaw puller for less than 100 bucks.super handy when all your regular pullers are to small. Did you put any heat on the screws before drilling them out?
1:33 Sorry, but... For your comfort, I suggest you buy an RV trailer with bathroom and kitchen, even if small, to take with you when you stay overnight. You work so hard and deserve amenities. G'd bless you!
![CAMPปลิ้น | EP.76[2/2] เดินมาสิบกว่าป่า วันนี้รู้แล้วว่าโจโฉกลัวอะไร!](http://i.ytimg.com/vi/R7Yor-t2Au0/mqdefault.jpg)
You gotta be good to run with this big dog. 10 hours from the shop and sleeping in a tent. No problem. Work done and filmed. And no complaints.
If you can't run with the " big dogs "..... stay on the porch.
Sleeping in a tent and 10 hours from home. Now that’s a hell of a field repairman. Props to you guys! Not many people out there now a days with the grit and will to do this kind of stuff. Good to see it still alive 🤙🏼🤙🏼
It helps that it probably pays very good
It should
On the fire line they don't just need good fire fighters .. they need good mechanics keeping things working great job !
Most people don't understand the art of firefighting, just controlling the fire hose takes a skill or it is dangerous. You are right though the mechanics of maintaining the pressure at the nozzle is very important. Just the design of the nozzle is critical to the success of the team fighting the fire. B.C.
Yeah, and don’t forget to pay them well
Respect for making that trip to help out your customer on this one. Being up in north California, getting close to Warren’s territory lol
Big respect doing this on the field !!!
Wow. Never seen a bearing quite like that. Great work, as always.
they're $$$ but are very forgiving alignment-wise
@@GordonTurnerr I've seen a roller bearing before. Not the pins lined up like a bracelet.
@@4thgradedropout980 I'm pretty sure they are double row cylindrical Roller bearings. So the inner race can pivot inside the outer race. Not a regular Roller bearing
@@GordonTurnerr Perhaps. I don't understand why that would be needed in an application as such. Almost like it doesn't even matter.
@@GordonTurnerr Spherical I think.
Maybe, tell the customer that grease is your friend and a saving's account. Old grease is not as good as new grease. Lol. 😁
A little tip I learned in the field with a bearing race inside an axle housing that was an interference fit and it had spun and stuck tight with no way to get behind it to knock or pull it out. Out of desperation, I went home and got a can of air duster, turned it upside down and sprayed the race until it was frozen and had shrunk enough to be pulled it out by hand. After that, I always keep a couple of cans in the shop and in my truck.
I didn’t see any grease in those old bearings. I would think to see some residue but they looked completely dry. Probably why they failed. Gotta keep that stuff lubed. Good job with that in not ideal conditions.
If it wasn’t for the few lazy operators who don’t grease we would be out of a job 😂😂
I love the fact that you have to get up close to read the "STAY BACK 300 FEET" sign
Man, your content never disappoints, from simple tanks welds in your shop to taking apart, diagnosing and fixing heavy equipment out in the boonies. Especially with your cool and collected demeanor and knowledge a young buck or not so young person can sure learn a LOT from you!
Amazing workmanship while tent camping. Love it.
That's the best way to support the firefighters, with equipment that's repairable in the field, so that they can make best use of it and it can put back into action if it breaks. Not to forget of the guys like you, that drive 10hrs away from home, sleeping in tents and give their best to keep that stuff up and running.
Thx for showing and for helping to save lives as well!
👍👍👍
Nice brother, used a freezer to shrink O- Rings for cylinder repack in hot weather. Nice ! Thanks for bringing us along. Stay safe.
Good Job guys. You overcame the issues that came up and got the job done. Doesn't get any better than that.
Adapt. Overcome. An get the d*mn thing up and running....
My kinda people and work.
Nicely done...👍
Broke out the torch; Time to stop the gentle tactics; cut that sucker out LOLOLOL Thanks for bringing us along!
And they didn’t screw anything up, that’s being careful.
Great job! You are lucky to have good customers and the support from them and the parts suppliers. 20hrs away is not where you want to have the wrong parts.
We own homes in both Siskiyou and Sonoma counties; both areas close to my homes have been ravaged by the fires over the past 5 years.
Happy Camp is west of my house; it’s far enough away but we’ve seen enough fire out here to last a lifetime.
It’s a team effort to keep the area safe. I want to personally thank you for being part of that team 🇺🇸
You guys have some nice stuff, Iam liking the neon green tools 👍🏼
Greg, 1:15 , man, when you snap a Snap-On hex driver, you are really having to torque it....
I had that issue on galvanized set screws in aluminum on a boat I took to the coast....
2 days later, they were hosed just like this.....
I know you have probably used or seen, but the hand held non powered impact drivers
you hit with a hammer are really good at getting hex, Phillips and Torx and slotted screws out
in these situations.....I bought one when I started out in 1973 because I could not afford an air tool
and had no compressor.....well I used for a short time, and never used again until 2008.....and
found it was super useful.....of course, I had been using air tools and thought it was not needed....
that slam/impact of the tool into the screw and your wrist turning gives a much better bite than
an electric or air tool.......I learned this working on Motorcycles and pulleys on industrial gear
....I hope this tidbit can help someone
out there.....cheers, Paul
p.s. my impact was made by Snap-On that I bought in 1973......and the drivers I twisted on the boat
were Snap-On from 1973...but when I used with the Hand Impact....the set screws came out.....Snap-On Rules !!!
Forward thinking of the designers to be able to bolt new shaft ends on
Ya no kidding. I was very happy when I realized that.
Snap on two,three and 4 leg pullers would of helped in this situation
Awesome job great fix be safe good luck on your trip back home 😊
Awesome video! I look forward to start welding this winter!
Well done. That truck must be packed with everything!☘️👍
One cabinet labeled "Camping gear"... bet its not Snap-On 😮😊
How you can cut off the bearing and not damage the shaft is amazing
Excellent work
Awesome work Greg, thanks for sharing
Thank you for your Videos. Please keep them coming.
As usually perfect job, well done.
Good on you for going out that far. Time away from home is time away from home no matter how good the job is.
Andrew Camarata Channel will have to have one of these units...
Thanks for sharing the Repair...
Amazing! All done in the middle of nowhere.
Pretty slick machine, looked like a tough job but also like it wasn’t very hard for you guys. 😂
Yet another OFW classic in the field action- great vid!
Great video man. I have seen most of your stuff on here. Imo you have mad skills.
Total respect to you 👍
Another great job,thank you for sharing 👍👍👍👍
Nice repair!!! Enjoyed
I can only imagine the lack of maintenance on that chipper.
I can’t believe there were parts available
Amazing work!!!
You are the man Greg.
Nice change in weather for you boys to work in.
Big job executed perfect🙌
You are the KING!
I do the same kind of work in new york. I love the idea of sleeping on site and working in that environment , but the eleven hour drive , not so much.
30👍's up on fire welding thank you for sharing 😎😲🎉😊
Anybody notice the clean/dry grease fittings on the bearing collars? No maintenance will cost you big time in the end.
I've seen guys with electric grease guns push the seals out of bearings on a mulcher head like that. Then it cant hold its grease and gets debris in the bearing and it fails early. I couldn't believe it either. It was about the only time i ever heard of something getting too much grease
Yeah i hope they put in some grease between the clips shown or that thing will be in pieces in a few days.
Assembly without lube is not that unsual if you have to heat the bearing tho.
@@MrAsddasdasda15:16
Interesting job.
Woooh! Great job!
Absolutely magnificent
Brilliant work
Damn! What a tough fix!
Calm, Cool, Collective.
Awesome road trip.
Nice job for what tools you had 👌
Well done young man. Looked a nasty task but you got it done. I refused welding work in London last year. Its about four hours south of me. The money was OK, but London is a nasty, expensive and unpleasant place.
You're customer is obviously worth working for and he obviously values you too!
London is fine?
You have to a a very good reputation in the industry because you get calls to service some very interesting clients.
Great job! 👍👍👍
Great video, thank you for sharing it. I didn’t realize that you travel north for work too. I’ve got a 12-16 hour job for you in Yuba County if you’re interested on the way back. It’s on a case 450 dozer.
This job was weeks ago. If you are serious send me an email. ofwwelding@gmail.com I will go anywhere.
Nice one.. hope it wasn't so cold that you guys had to share a sleeping bag.. 😉🙂👍
You are amazing!
your masticator has masticated too much it seems.....looks like cooler weather for you.....best wishes from florida, Paul
I've used a die grinder before to get those rollers out. Just make a pocket and move them one by one to it and pull them out. But I had to save the shaft and it was quite time consuming.
Hmmm, I'm slipping, I missed this one when it came out. Those mulchers are horrific. I've seen them on skid steers also.
It is amazing the bearings can stand the hammering that goes with the job.
Cool work thanks 👍
You guys are the real deal lol 👍
10+ hour drive to a job, that's a trip.
Привет мой друг! Занимаюсь такой же работой как и ты, приятно смотреть на работу профессионала!
It’s like one of the Russian nesting dolls 😂 great job
Damn boy, what do you do for an encore, repair a shive on a tower crane, damn good work and a hell of a work ethic.
well done sir !
Can’t be stuck if it’s liquid. Thanks for sharing.
Good skills bro 🍺
That was the funniest looking bearing I've ever seen
13:29 The most satisfying thunk ever
I would love to do work like this.
7:35 Whole time I was like, "what if it's not really seized?" Then, "ooh, that's not right."
get you a 101L cutting tip. great for cutting out bearings and bushings. Made shop buy me one cause they are pricey, about $200 here in the midwest.
The Official Fire Support Sticker on the back of the Rig!
Great stuff
nice aluminum ramps.
Can't be tight, if it's now liquid 😂
Dang, hope it paid well for that drive!
Snap-On tools…nice!
Excellent.
Great Vid 👍👍👍👍👍👍
Morning Coffees on!!Here we go!!Cheers!!;-))!!
good job boss
heating a bearing race with oxy... you guys are savages!
Honestly had to watch this just to see what a masticator head is. These should be used in a zombie movie.
Amazon has a huge hydraulic 3 jaw puller for less than 100 bucks.super handy when all your regular pullers are to small. Did you put any heat on the screws before drilling them out?
The bearing was seized to the shaft. Don’t think a puller would have helped. I did try heat on the bolts.
Just wow !!!!
didn't see any grease in the old Bearings. Grease is cheaper than the Bearing. --operator Responsibility Expensive repair.
1:33 Sorry, but... For your comfort, I suggest you buy an RV trailer with bathroom and kitchen, even if small, to take with you when you stay overnight. You work so hard and deserve amenities.
G'd bless you!
Man, this is like MASH meatball surgery! Nice job.
The engine group that you have on film at 446 is of my county and department.
Must have asbestos hands! How can you handle that bearing looked mega hot, great work as usual pal
My wife says the same thing when I take stuff out of the oven with my bare hands.
@@OFW 🤣
What causes it to seized up looks like it was well maintained love your videos be safe and have a great day Sam
Lack of grease.
@@OFW ok just look like it was well maintained thanks for the comeback have a great day
Now I know what a mastication is 😂
I live in willow creek. Know alot of guys on dozens there
And here I am thinking that stuck swingarm axle on a 80cc motorcycle gave a fight.