Nice attachment, but I would suggest turning the smallest end diameters last. Maintain the support for as long as you can for rigidity and safety. Same principle for turning steel.
I’ve found that burnishing the wood produces a gorgeous and hard finish (after sanding) - I often use a cutoff from an oily species like olive, and rub it firmly against the rotating piece (at low speeds)
I made a shield out of a polycarbonate panel that I folded and stretched to the top of the duplicater. It does a great job of keeping shavings from hitting me and also make cleanup easier
Thanks for this! Do you have the cutter head in the center or just below center? Mine is leaving a lousy finish. It looks like it was a stabbed a bunch.
Hi. Yes the cutter head should be just below center. I would suggest you speed up the lathe speed and be sure to keep the "ship wheel" moving at all times.
@@gordlanger7064 Thanks Gord! I’m doing both of these things that I’m wondering if I am sharpening my cutter incorrectly. Do you have any advice about that?
Ola amigo tudo bem com você Me chamo Odair lucas. Pais Brasil Parabéns. Você teria um vídeo do passo a passo desse seu copiador? Ficou excelente estou precisando fazer um evo seu foi o melhor que eu vi. Mais uma vez parabéns.
Hi, its a Vega. All the information needed is in my article (issue #57) on this site: archive.constantcontact.com/fs030/1103251462235/archive/1103792031624.html Cheers, Gord
Nice attachment, but I would suggest turning the smallest end diameters last. Maintain the support for as long as you can for rigidity and safety. Same principle for turning steel.
Great info! I would take off your ring prior to putting hands near the turning lathe.
😄
I’ve found that burnishing the wood produces a gorgeous and hard finish (after sanding) - I often use a cutoff from an oily species like olive, and rub it firmly against the rotating piece (at low speeds)
Nice machine. It looks like you need another lathe. One for the duplicator and one for final finishing.
Hi Wayne, I get between $40 and $60.00 / pin depending on the type of wood being used.
Cheers, Gord.
I made a shield out of a polycarbonate panel that I folded and stretched to the top of the duplicater. It does a great job of keeping shavings from hitting me and also make cleanup easier
What technique do you use to form/manipulate the polycarbonate?
@@mavenfeliciano1710
I just used a heat gun and folded it over the edge of a board.
I learned some things, thanks.
Great video! Please let me know template's typical extra room from the end of profile to be left for holding down in the duplicator.à
Цікавий копірувальний пристрій, мені сподобалось.
Thanks, Gord! I look forward to watching more of your videos!
Will that lathe duplicator work well with mahogany?
What lathe are you using? I’d love to get one
Thanks for this! Do you have the cutter head in the center or just below center? Mine is leaving a lousy finish. It looks like it was a stabbed a bunch.
Hi. Yes the cutter head should be just below center. I would suggest you speed up the lathe speed and be sure to keep the "ship wheel" moving at all times.
@@gordlanger7064 Thanks Gord! I’m doing both of these things that I’m wondering if I am sharpening my cutter incorrectly. Do you have any advice about that?
Do you have a video om the set up of a Vega dup. I just got a used one and need help
Terry
Sorry do not have a set up video. Perhaps contact vega woodworking directly.
How much do you get for your French Pastry Rolling Pin?
Каска прикольная
Do you have plans of how you made this? This is awesome. I’m subscribing to this.
Hi the duplicator is from Vega . I purchases it from them. It was expensive but well worth it. Thank you for your comments. Gord
Ola amigo tudo bem com você
Me chamo Odair lucas.
Pais Brasil
Parabéns.
Você teria um vídeo do passo a passo desse seu copiador?
Ficou excelente estou precisando fazer um evo seu foi o melhor que eu vi.
Mais uma vez parabéns.
Olá Odair. Obrigado por seus comentários! Envie-me seu endereço de e-mail e eu lhe enviarei algo.
gord@langercraftworks.com
Valeu vou enviar.
Obrigado
Olá amigo tudo bem.
Com suas informações eu consegui fazer um copiador.
Muito obrigado mesmo.
Which food grade finish do you recommend? Do you not recommend applying the finish while turning at a slow speed then parting the ends?
I use food safe salad bowl finish while on the lathe slow speed to start the high speed to finish off. Then part the ends. Gord
Hi Bees Wax or Salad Bowl finish is the best/ safest to use. Gord
Where can I buy that duplicator?
Is there a link to your website?
Good idea!
Can you duplicate chess pieces with this?
BTW, thanks for the video!
Finish it off with 220 on a random orbit sander while it's turning and you'll have zero scratches.
hello sir it was a great vid were can I get a duplicator like that to buy and how much will it cost thanks
thanks mr langer
Thanks
Subbed
Can we make a drum stick on this machine?
Not sure, sorry. They are thin and may whip without additional support. A Spindle steady rest would help.
Which (brand) lathe is this ?
Hi, its a Vega. All the information needed is in my article (issue #57) on this site:
archive.constantcontact.com/fs030/1103251462235/archive/1103792031624.html
Cheers, Gord
what price Pakistani
where's the template...
عمل رائع وجميل .. ممكن ترينا مكونات الصندوق و محتوياته ولكم منا فائق الشكر
Any one make one temp plate turn
I am sorry I dont understand your question. Gord.
verga mucho bla bla y yo sin saber ingles