BMW E90/E91/E92 xDrive Front Control Arm,End Link,Tie Rod &Ball Joint DIY(325xi, 328xi, 330xi,335xi)

แชร์
ฝัง
  • เผยแพร่เมื่อ 2 เม.ย. 2020
  • ►If you're experiencing any popping, clunking, or clicking sounds while traveling over rough surfaces, this kit is for you. In this DIY Mike takes through the refresh process of his E91 Wagon's front suspension. It was in desperate need of some front end love!
    This is a 10-piece kit designed in-house here at FCP Euro utilizing Lemforder replacement parts including control arm and ball joint assemblies, ball joints, stabilizer bar links, tie rods, and steering rack bellows. These parts from Lemforder are the same components that would have been installed on the vehicle from the factory.
    We recommend replacing all of these components if you have in excess of 80K miles on your vehicle and still have original components. We also encourage that you replace your control arm components if you are experiencing the following symptoms:
    -Popping, clunking, or clicking sounds while traveling over bumps or dips in the road
    -A disconnected feeling between the steering wheel and front end of the car
    -Vehicle is slow to respond to steering inputs
    -Vehicle wanders on the highway or will not drive straight
    -Vehicle cannot be aligned properly due to play in front suspension
    BUY THIS KIT: www.fcpeuro.com/products/bmw-...
    FOLLOW THIS DIY ON OUR BLOG: blog.fcpeuro.com/how-to-repla...
    BMW Hex Screw With Collar: www.fcpeuro.com/products/bmw-...
    BMW Self-Locking Hex Nut: www.fcpeuro.com/products/bmw-...
    Inner Tie Rod Tool - Lisle 45750: www.fcpeuro.com/products/inne...
    The kit is applicable to the following vehicles:
    BMW 325xi
    2006 BMW 325xi
    BMW 330xi
    2006 BMW 330xi
    BMW 328xi
    2007 BMW 328xi
    2008 BMW 328xi
    BMW 335xi
    2007 BMW 335xi
    2008 BMW 335xi
    BMW 328i xDrive
    2009 BMW 328i xDrive it
    2010 BMW 328i xDrive
    2011 BMW 328i xDrive
    2012 BMW 328i xDrive
    2013 BMW 328i xDrive
    BMW 335i xDrive
    2009 BMW 335i xDrive
    2010 BMW 335i xDrive
    2011 BMW 335i xDrive
    2012 BMW 335i xDrive
    2013 BMW 335i xDrive
    BMW X1
    2013 BMW X1 xDrive28i Suspension Control Arm Kit
    2013 BMW X1 xDrive35i Suspension Control Arm Kit
    2014 BMW X1 xDrive28i Suspension Control Arm Kit
    2014 BMW X1 xDrive35i Suspension Control Arm Kit
    2015 BMW X1 xDrive28i Suspension Control Arm Kit
    2015 BMW X1 xDrive35i Suspension Control Arm Kit
    Get free parts from FCP Euro:
    www.fcpeuro.com/page/lifetime...
    Follow FCP Euro on:
    / fcpeuro
    / fcpeuro
    / fcpeuro
    www.fcpeuro.com/
    SUBSCRIBE: hubs.ly/H0cDnfN0
  • ยานยนต์และพาหนะ

ความคิดเห็น • 202

  • @fcpeuro
    @fcpeuro  3 ปีที่แล้ว +3

    Buy this kit for your E90 Here! www.fcpeuro.com/products/bmw-10-piece-control-arm-kit-e90-e91-e92-e90caxdrive2?

  • @GautamKumar-cr7tw
    @GautamKumar-cr7tw 3 ปีที่แล้ว +13

    I don't know how much I can thank you guys for saving me money at the dealership. Absolutely love it. The detailed instructions in these videos help me more than the Bentley Publishers E90 Repair manual. Thank you!!!

  • @bategoiko396
    @bategoiko396 3 ปีที่แล้ว +10

    Did that job a week ago... with the car on jack stands in the driveway. I don't know what kind of air hammer did you use, mine is scfm2.7@90psi and it didn't do the job with the ball joints, i had to massage the old ball joints with the hammer 🔨 with the jack under the hub. For the driveway diy-ers - put some time to remove the brake disc and the brake disc dust shield before, that opens a lot of space, don't forget to "turn the wheel" to the left or right side to have even more space, and finally, if you're replacing the inner tie rod as showed in the video, just cut it with a grinder, in my case the propane torch was complete waste of time in the battle against the canadian salt corrosion...if you're replacing only the outer tie rod, cut the old outer rod gently to free up the threads without cutting the thread of the inner rod.
    Good luck

    • @tupan901
      @tupan901 ปีที่แล้ว +2

      That is exactly what I did with my tie rods lol. Hit em with pb blaster the night before, nothing. Hit em with the torch the next day, nothing. Then realized if I just bust out the grinder and cut it right in the middle I could slip the tie rod extension right over the remainder of the rod. Had them off in 10 min.

    • @denkorch
      @denkorch 2 หลายเดือนก่อน

      Straight to the point 100% ended up doing the same but before reading this comment lol

  • @jim8688
    @jim8688 3 ปีที่แล้ว +43

    “N52 problems am I right?” That one hit me deep

    • @fcpeuro
      @fcpeuro  3 ปีที่แล้ว +6

      😂

  • @nickdiaz416
    @nickdiaz416 4 หลายเดือนก่อน +1

    I did this entire job while doing the oil pan and mounts. Thank you Mike your videos have helped me a lot along my journey and definitely brings in the sales while saving us money. Much appreciated Mike and FCP!

  • @stageiimike2145
    @stageiimike2145 2 ปีที่แล้ว +1

    Thank you for making these videos, you guys are a life saver, excellent mechanics doing the work.

  • @ankursharma1232
    @ankursharma1232 4 ปีที่แล้ว +2

    This guy talks about car parts like hes talking about drinking a glass of water. Amazingly passionate about his job.

    • @fcpeuro
      @fcpeuro  4 ปีที่แล้ว +1

      All passion here at FCP Euro! Thanks, Ankur!

    • @ankursharma1232
      @ankursharma1232 4 ปีที่แล้ว +1

      @@fcpeuro You guys thinking of opening in the UK?

  • @Crystalbaba
    @Crystalbaba ปีที่แล้ว

    One of the best repair videos I have seen !!!

  • @kostas_wellknown4519
    @kostas_wellknown4519 2 ปีที่แล้ว +1

    You are perfection hidalgo my friend! Well done really good video!

  • @Shamus71
    @Shamus71 4 ปีที่แล้ว +6

    “Big Nasty”... sounds like South Main Auto lol.
    Thanks for this video. I have to do my front arms and will be ordering Lemforders from you guys soon.

    • @fcpeuro
      @fcpeuro  4 ปีที่แล้ว +2

      😁 No problem, hope it helps when the time comes to do your install! Appreciate the support Shane.

  • @crazy4gta1
    @crazy4gta1 6 หลายเดือนก่อน +1

    For anybody struggling with the ball joint blocked by the axle, I was able to remove it by squeezing a 24mm socket and ratchet onto the nut. If your socket and ratchet is small enough, you have JUST enough room to wedge it under the axle boot if you move the rubber a little. And if the ball joint spins, use a jack and put some pressure on the bottom of the joint. The friction stops it from spinning

  • @albert427
    @albert427 4 ปีที่แล้ว +1

    Good Job Big Nasty... Very informative and entertaining.

    • @fcpeuro
      @fcpeuro  4 ปีที่แล้ว +2

      glad you enjoyed it albert427!

  • @MischeifMakerz
    @MischeifMakerz 4 ปีที่แล้ว +5

    Loved this

    • @fcpeuro
      @fcpeuro  4 ปีที่แล้ว

      We love that you loved it MischeifMakerz

  • @cdv721
    @cdv721 2 ปีที่แล้ว +1

    Extremely informative

  • @davidchesla3348
    @davidchesla3348 3 ปีที่แล้ว

    All I can say is Great video, best I have seen in a long time. THANKS

    • @fcpeuro
      @fcpeuro  3 ปีที่แล้ว

      Thanks so much for the kind words David!

  • @PeterMaenke
    @PeterMaenke 4 ปีที่แล้ว +1

    Great video! Definitely earned my purchase of this kit.

    • @fcpeuro
      @fcpeuro  4 ปีที่แล้ว +1

      Thank you Peter, glad you liked the video and we appreciate the support! Good luck on the install, let us know how it goes.

  • @chriswise7142
    @chriswise7142 4 ปีที่แล้ว +19

    FYI, the wishbone needs to be torqued to the subframe at "normal position" also. great video other than that!

    • @fcpeuro
      @fcpeuro  4 ปีที่แล้ว +2

      Yes, you are absolutely right, Chris! Glad you like the video!

    • @sofuknossum1
      @sofuknossum1 3 ปีที่แล้ว +1

      FCP Euro do you not need to have the car at ride height when torquing down the sway bar end links? Keep hearing a lot of different opinions and would like to know before I throw my end links on this week. Thank ya.

    • @matthewmoser2090
      @matthewmoser2090 2 ปีที่แล้ว

      @@sofuknossum1 no

  • @bootyklap7861
    @bootyklap7861 3 ปีที่แล้ว +1

    lovely knockers

  • @mr.n5435
    @mr.n5435 3 ปีที่แล้ว +4

    @7:34 He is really in there lol.... His trying hard not to stip that T50 Bolt. Great Job brother, you can work on my n54 e90xi anytime. Awesome video 👍

  • @SteveWeltman
    @SteveWeltman 4 ปีที่แล้ว +10

    Baby counter... Hilarious! great content and put the fun back in control arm diagnosis for the E9X platform. Just don't get [nearly] hit in the face by a control arm like Mike; brace, tape, tie wrap or just restrain the arm from swinging on it's own when you're removing it. Or look for a good (available) dentist first.

    • @fcpeuro
      @fcpeuro  4 ปีที่แล้ว +1

      Thanks Steve! If you aren't having fun while working on your car then you're doing it wrong! That control arm swing was a few inches away from Mike needing a new front tooth and a pair of glasses ^.^

  • @legambaz
    @legambaz 4 ปีที่แล้ว +3

    Excellent instructions.

    • @fcpeuro
      @fcpeuro  4 ปีที่แล้ว +1

      Thanks Alofzico glad you approve!

  • @rlklunk
    @rlklunk 4 ปีที่แล้ว +2

    Big Nasty! My other favorite car repair channel..

  • @scanspeak00
    @scanspeak00 4 ปีที่แล้ว +2

    Great video and the main thing I learned is that this repair is probably out of my league.

    • @fcpeuro
      @fcpeuro  4 ปีที่แล้ว

      Didnt mean to convince you of that scanspeak00! Really aside from the bushing, its not that bad, but that one portion can become quite frustrating. Thanks for watching, and let us know if you have any questions!

  • @miguelgarcia5773
    @miguelgarcia5773 4 ปีที่แล้ว +3

    Wild!! Snapped. Made it seem nice and easy... but I bet that sh*** is hard to do

  • @ralphcastillo9266
    @ralphcastillo9266 2 ปีที่แล้ว +1

    You have the best video out there for this Job 👍

    • @fcpeuro
      @fcpeuro  2 ปีที่แล้ว +1

      Happy to be of help, Ralph!

  • @sheldonm3535
    @sheldonm3535 4 ปีที่แล้ว +2

    I did a refresh with oem m3 parts on my 335i e92 rwd n54. Wow what a diff!

    • @fcpeuro
      @fcpeuro  4 ปีที่แล้ว +1

      Your 335i must feel better than new!!

  • @jesusdiaz9077
    @jesusdiaz9077 ปีที่แล้ว +1

    🤣🤣🤣 he got me at the “n52 problems am I right ??? “ 🤨😭

  • @bassandtrebleclef
    @bassandtrebleclef 4 ปีที่แล้ว +4

    I just changed the windshield washer pump on my E91 and was short on space. I can't imagine doing this control arm/tie rod job without a lift and getting clear access under the car with room to work. I'd still buy the parts from FCP because I trust you guys, but man, it's a ball breaker working on the floor for this type of stuff. At least for an old guy like me.

    • @fcpeuro
      @fcpeuro  4 ปีที่แล้ว +1

      Thank you for trusting us! The main reason we do our DIY's on a lift is so that our camera man can get under there and show you guys exactly what is going on. Working on the floor is tough, we've been there!

  • @CREAOOfficial
    @CREAOOfficial 2 ปีที่แล้ว +2

    Just tackled this. CRUNCHYSANN’s BALL JOINT PRESS IS A MUST!!! $130.

    • @fcpeuro
      @fcpeuro  2 ปีที่แล้ว +3

      A stuck ball joint can 100% make or quite literally break this job. Glad you got it done though creao!

  • @eddieellison7679
    @eddieellison7679 3 ปีที่แล้ว +1

    You don’t have that we don’t have that no one has that! Well said.

    • @fcpeuro
      @fcpeuro  3 ปีที่แล้ว +1

      😂

  • @ltcterry2006
    @ltcterry2006 2 ปีที่แล้ว +2

    I was just told my X1's front end can't be aligned as the outer tie rod end adjustment is too corroded. I've done this job on an '06 X3 I had. The air hammer is genius! I ended up taking the entire hub off and clamping it to a work bench to use a pinch and a mallet. Putting the hubs back on the half axel splines was miserable. Miserable. I guess if I'm going to do tie rod ends I should go ahead and to ball joints and control/thrust arms, too. Car has 66k miles. About time. Thanks for the video!

    • @crazy4gta1
      @crazy4gta1 7 หลายเดือนก่อน +1

      Fcp sells a tool that pulls the axle shafts into the hub. Makes life 10 times easier

  • @milesamador5158
    @milesamador5158 2 ปีที่แล้ว

    excellent !

  • @minermarcus
    @minermarcus 2 ปีที่แล้ว +1

    I mistakenly watched this in the morning instead of the evening. Taking a shot every time he says baby, now I’m worthless for the rest of the daay.

    • @fcpeuro
      @fcpeuro  2 ปีที่แล้ว +1

      🤣😂🤣 What a way to roll the dice and start your day minermarcus!

  • @Arrozconchopsticks
    @Arrozconchopsticks ปีที่แล้ว +1

    I really need to get this kit. My front end looks like the titanic

  • @DayoftheJakeL
    @DayoftheJakeL 3 ปีที่แล้ว +1

    I pulled me ball joints with the slide hammer vice grips from Vegas tool.

  • @rider9195
    @rider9195 4 ปีที่แล้ว +8

    Digging the Big Nasty reference!

  • @javarithms
    @javarithms 4 ปีที่แล้ว +7

    Control arm bushings connected to the subframe have to be torqued with the car in normal height position (i.e. tires on the ground) or the bushings will fail prematurely.

    • @fcpeuro
      @fcpeuro  4 ปีที่แล้ว +4

      You are absolutely right, you can also jack/compress each corner of the suspension that you are tightening to simulate it being on the ground with it on the lift or on jack stands.

  • @GLeszega
    @GLeszega 3 ปีที่แล้ว +1

    Just did the control arms on my e92 today and didn’t tq at ride height. Is that really a problem? I don’t want to take it all apart again lol

  • @Dackelone
    @Dackelone 4 ปีที่แล้ว

    Nice video. You should post a link for that Lisle 45750 tie rod tool. Also... shouldn't you have tightened BOTH inner link bushings at right height >? Why only the rear bushing and not the forward one ?

  • @friguy4444
    @friguy4444 8 หลายเดือนก่อน

    Great as always FCP Euro! Thank you! However I'm confused about something. I've seen other videos showing the replacing of the Control Arms and the ball joint for it wasn't part of the control arm (They claim to be doing the X drive version just like you guys). It's actually attached from the top on the wheel assembly. It still looks like it fits in the same way but is a separate unit or part all it's own. What's the scoop on that??

  • @cw988
    @cw988 6 หลายเดือนก่อน

    Great video, thanks. One tip... I thought that the bushing bolts should be tightened up at ride height.

  • @JosephusXIX
    @JosephusXIX 3 ปีที่แล้ว +1

    Would a front wheel alignment be needed in this case, or just recommended?

  • @greatestever7623
    @greatestever7623 3 ปีที่แล้ว +1

    can you just replace the bushings and nuts if the actual strut is still in good condition?

  • @jonathanfinlay3613
    @jonathanfinlay3613 4 ปีที่แล้ว +1

    Thoughts on useing a .22 ramset instead of an air hammer? Am I crazy?

  • @davidchesla3348
    @davidchesla3348 3 ปีที่แล้ว +2

    If you put the ball joints in the freezer they slip right in. We use to do that on aircraft parts. I didn't have to do any tapping.

    • @fcpeuro
      @fcpeuro  3 ปีที่แล้ว +1

      That's an interesting tip David... we are going to have to try that out!

  • @dootieflack
    @dootieflack 3 ปีที่แล้ว +1

    is that astro 4980 must-have? or should .401 hammers be able to get the ball joints out?

  • @nickblasko5210
    @nickblasko5210 4 ปีที่แล้ว +1

    How many new nuts and bolts did you need for installing the new kit?

  • @mehtaaba6453
    @mehtaaba6453 3 ปีที่แล้ว +1

    Could you a video for a suspension replacement like this on a 328i?

  • @bategoiko396
    @bategoiko396 4 ปีที่แล้ว +1

    Excellent!!! Thank you for the video!
    Can you do the rear suspension as well?

    • @fcpeuro
      @fcpeuro  4 ปีที่แล้ว +2

      bate goiko we will have one for the rear kit coming out sooner rather than later, just stay tuned!

    • @bategoiko396
      @bategoiko396 4 ปีที่แล้ว +1

      @@fcpeuro I'm tuned, subscribed with notifications on baby 😜😜😜
      P.s. really looking forward to see what kind of bushing removal tool are you using ( for the control arms and for the subframe bushings)

  • @perryoh698
    @perryoh698 6 หลายเดือนก่อน +1

    god I love FCP

    • @fcpeuro
      @fcpeuro  6 หลายเดือนก่อน +1

      💙

  • @willspurzem6509
    @willspurzem6509 3 ปีที่แล้ว +2

    Great video... QUESTION: my '10 e91 xdrive feels like the frame is going to slam apart when I hit a change in road surface like a 3/4" pavement change or a bump.. is this front end links, strut mounts, or do I need to do the whole front end? it is so bad it cocked one of my headlights down.

  • @AnticipatedHedgehog
    @AnticipatedHedgehog 4 ปีที่แล้ว

    Bam Baby!

    • @fcpeuro
      @fcpeuro  4 ปีที่แล้ว +1

      What can we say, Mike gets very excited when parts come off of his car ^.^

  • @michaell.445
    @michaell.445 ปีที่แล้ว

    I'm wondering why you didn't opt for the ball joint removal tool that you sell.

  • @Bakdons-yn3cg
    @Bakdons-yn3cg 2 ปีที่แล้ว

    ISTA+ shows 68 Nm + 90° for the bushing bolts. The video shows 100 Nm. Which one is correct?

  • @NicolasCageIsActuallyARobot
    @NicolasCageIsActuallyARobot 4 ปีที่แล้ว +1

    When torquing the lower control arm bolts to 100Nm + 90 Degrees, do you need to replace the bolt each time you take it off and re-torque it? Usually degree values mean it's TTY, but I've seen conflicting information about it. I definitely don't want to snap it next time I remove/reinstall it.

    • @fcpeuro
      @fcpeuro  4 ปีที่แล้ว +1

      You can always replace the bolt to be on the safe side!

  • @federicotorresbordils7624
    @federicotorresbordils7624 3 ปีที่แล้ว +2

    Are torque specs the same for RWD?
    Thank's in advance.
    BimmerN53

  • @alexandercarlsson
    @alexandercarlsson 2 ปีที่แล้ว +1

    Feels like a good Saturdays work.
    I am just curious about that Tie Rod Tool. Can this be done without that special tool? Do you have access with a reglar extended wrench?
    My 330Xi pulls to the right when braking and vibrates at around 70mph. New Rotors and wheels balanced. So i have decided to change out everything for the front suspension..

    • @fcpeuro
      @fcpeuro  2 ปีที่แล้ว +2

      It should be doable without, this just makes it really easy to properly torque it down and reach from afar. Like you said nothing that can't be accomplished on a nice long saturday in the driveway!

  • @FreePaly1948
    @FreePaly1948 2 ปีที่แล้ว +1

    Thanks for the video! Do you know if the process for the tie rod will be similar on an F30 xDrive?

    • @fcpeuro
      @fcpeuro  2 ปีที่แล้ว +2

      Hi Rabih El-Hendi, the idea will be very similar!

  • @stephanelouvet1113
    @stephanelouvet1113 2 ปีที่แล้ว +3

    Very nice step by step tutorial !
    22:15 - Can we tighten this bolt while the wheel is hanging down ?
    Isn't it better the lock it while the car is on the ground so the internal bushing isn't twisted ?
    26:08 - I would have use a normal ratchet and not a torque wrench for the +90°. I've been told to not force on a torque wrench over the clic.
    Thank you
    Edit : I found the answer in the comments. OK.

    • @ThunderbirdRocket
      @ThunderbirdRocket 6 หลายเดือนก่อน

      Do you mind if I ask you what was the answer / correct procedure for this step ?

    • @stephanelouvet1113
      @stephanelouvet1113 6 หลายเดือนก่อน +1

      @@ThunderbirdRocket Waow
      That was 2 years ago and by now I made myself my E92 suspension refresh.
      The rule is simple, every join with a solid rubber bushing must me tighten and torqued when under load. Either with the car on his wheel if you have a lift and can go under or by lifting the knuckle with a floor jack until the car body slightly loose contact with the nearest support stand.

    • @ThunderbirdRocket
      @ThunderbirdRocket 6 หลายเดือนก่อน

      @@stephanelouvet1113
      Right on ! Super helpful of ‘ya mate !! I appreciate your taking the time to help me out ! 👊🏼🕊

  • @Jeff-bw5kw
    @Jeff-bw5kw 4 ปีที่แล้ว

    Please double check your 60 Nm torque spec on the bolt for the thrust arm to the steering knuckle. Bentley says “Tension strut to steering knuckle 165 Nm”. Thanks!

  • @dootieflack
    @dootieflack 2 ปีที่แล้ว +1

    How TF did you get the 24mm wrench on that lower control arm nut???
    Absolutely nothing fits: wrench, socket, etc...

  • @chp9990
    @chp9990 9 หลายเดือนก่อน

    The self locking nut in the description says it doesn’t work for my 2010 bmw 335xi is that true ?

  • @doug964
    @doug964 3 ปีที่แล้ว +1

    When doing front end work on jack stands. Especially on this 328xi. Is there any jack point to lift both front tires in air? I’m looking at the area near the stiffening plate.

    • @fcpeuro
      @fcpeuro  3 ปีที่แล้ว +2

      Absolutely agree, luckily, we have access to a life on the regular. For the E9X cars, there is a center jack point - should be a bit of rubber or an exposed section under the skidplate in the front middle of the car. From there you can get the front end in the air and up on 2 jack stands at the same time.

  • @honorablewiz7447
    @honorablewiz7447 ปีที่แล้ว

    I used a$150 press tool from Harbor Freight to get that ball joint out.

  • @Bennymarz
    @Bennymarz 2 ปีที่แล้ว

    Anyone know where I can find torque specs for e92? I have the repair manual and it only shows torque codes like 31 21 1az….

  • @fyttirackarn
    @fyttirackarn 3 ปีที่แล้ว

    Interesting to see this. My G31 is clunking / rattling a bit going over speed bumps. BMW says it's the tie rods bushings with some "oilbearings" that are cracked / worn. They also say troubleshooting, new tie rods, installation and wheel alignment is a 1700 USD job. Seems unreal watching this video that made changing ALL "rods" seem pretty easy.
    Lucky me this is a warranty job. But knowing this in the future I'll buy any parts myself and let some non-BMW shop do the work.
    Also watching this I'll be sure to ask them if any other bushings are worn too, thinking control arms most likely would be.

    • @fcpeuro
      @fcpeuro  3 ปีที่แล้ว

      definintely ask! tie rods are steering and control arms are suspension, but they typically wear out at the same rate!

  • @ozarkdaredevils
    @ozarkdaredevils 2 ปีที่แล้ว

    I watch your videos , excellent video and I buy your parts ... thank you

  • @shize9ine
    @shize9ine 3 ปีที่แล้ว +2

    For the E91, non x-drive, am I better off going with the M3 components?

    • @fcpeuro
      @fcpeuro  3 ปีที่แล้ว +2

      Its a common upgrade we often see done, and don't necessarily say you should do one over the other. Buttttt the M3 stuff is pretty sweet...

  • @TK-gd9td
    @TK-gd9td 4 ปีที่แล้ว +1

    Could you guys do one for f30 gen?? Would love to DIY refresh my set up.. ty!

    • @fcpeuro
      @fcpeuro  4 ปีที่แล้ว +1

      We plan on it!

  • @kingpin16052
    @kingpin16052 4 ปีที่แล้ว +2

    I’ve been fighting that ball joint for 5 years. Everything has been replaced except that... YOU WILL NEED AN AIR HAMMER PEOPLE lol

    • @fcpeuro
      @fcpeuro  4 ปีที่แล้ว +1

      kingpin we were dreading it going into shooting this DIY bc we feared how bad itd be to get out. We had planned to make our own slide hammer setup to try to avoid using an air hammer as not everyone has access to one... but we didn't have the time (nor patience ^.^) unfortunately.

  • @inzomniiak
    @inzomniiak 3 ปีที่แล้ว +1

    question. I did all that in my car by myself and when I drove the car for alignment the guy there told me that supposedly he can't align it because I need cambers in the front and back
    and the second reason is because supposedly the car is to low. I I never lowered my car and I have the same rims that came with the car which means its not low at all but he is the professional according to what he said. Is there any suggestion about that or is it even true that I need cambers to be able to do that ? the kit I used is exactly the same as the one you used in this video. Please let me know. I will greatly appreciate any help.

    • @fcpeuro
      @fcpeuro  3 ปีที่แล้ว +1

      We would suggest going to another shop, non of that really makes sense given your circumstances.

  • @abisismael1343
    @abisismael1343 4 ปีที่แล้ว +1

    Very interresting

  • @AustinChappell
    @AustinChappell ปีที่แล้ว +1

    Random question but why did you need to remove the reinforcement plate from the subframe? I’m about to embark on this job and it seems like you can get away without doing all that.

    • @fcpeuro
      @fcpeuro  ปีที่แล้ว +1

      Hi Austin, having the reinforcement plate out of the way allows you more room to work with when installing the tie rod boot on and the clamp. If you are not servicing the tie rods, then no need to remove it!

    • @AustinChappell
      @AustinChappell ปีที่แล้ว +1

      Thank you! You guys are the best.

  • @jeepee7091
    @jeepee7091 หลายเดือนก่อน

    22:50 How did he torque the bolt? Is there an adapter on the wrench?

  • @61dirtrider61
    @61dirtrider61 2 ปีที่แล้ว +1

    Do you need that tie rod tool to get the inner out to put new one in?

    • @fcpeuro
      @fcpeuro  2 ปีที่แล้ว +1

      On some vehicles you can use a thin wrench, however oftentimes with an Xdrive vehicle like this one, the drivetrain or subframe can get in the way of spinning a wrench in there.

  • @zakkhan410
    @zakkhan410 4 ปีที่แล้ว +4

    Can you do rear complete suspension as well

    • @fcpeuro
      @fcpeuro  4 ปีที่แล้ว +7

      Zak Khan we will have one for the rear kit coming on horizon, just stay tuned!

    • @epaminontas6972
      @epaminontas6972 4 ปีที่แล้ว +1

      @@fcpeuro is it out yet?

  • @nathanh1425
    @nathanh1425 4 ปีที่แล้ว +1

    What is the accurate number of estimated labor hours an Independent shop should charge to do this entire job? I would like to buy the kit but I will have a technician do the job. Don’t have the tools or setup for this. Thanks!!

    • @fcpeuro
      @fcpeuro  4 ปีที่แล้ว

      This is probably around a 2-2.5 hour job.

  • @Jeff-bw5kw
    @Jeff-bw5kw 4 ปีที่แล้ว

    Also, www.newtis.info/tisv2/a/en/e90-335xi-lim/repair-manuals/31-front-axle-front-suspension/31-12-wishbones-struts-including-rubber-mounts/5bUExgU lists different torques for E90 AWD:
    “Compression strut to front axle support” (I believe this is thrust arm to chassis): 68 Nm + 90 deg
    “Compression strut to guide joint” (I believe this is thrust arm to ball joint”): 80 Nm
    These are quite different than what the video says!

  • @willharris7063
    @willharris7063 4 ปีที่แล้ว

    Mike!!!!!

    • @fcpeuro
      @fcpeuro  4 ปีที่แล้ว

      Will!!!!!!

  • @matthewnicholas6365
    @matthewnicholas6365 2 ปีที่แล้ว

    I'm going to tackle this on my F25 X3 and the parts look very similar. The ball joint is the part troubling me the most.
    Is it not possible to leave the control arm bolted to the ball joint and use the arm to pry the ball joint out?

    • @fcpeuro
      @fcpeuro  2 ปีที่แล้ว +1

      Hi Matthew, due to the tight press fit of the ball joints, it is nearly impossible to get them out using the arms as a pry tool in our experience.

    • @matthewnicholas6365
      @matthewnicholas6365 2 ปีที่แล้ว

      @FCP Euro the other idea that popped into my head was screwing the bolts in from the top down and prying a chisel in between the knuckle and the tabs. Screwing the bolts down against the chisel to push down on the ball joint.
      Can't picture in my head if it would work or if it would just bend the tabs down.
      And then I thought - what would happen if you bent the tabs down and then hammered them to spin the ball joint around to free it?

  • @irv7332
    @irv7332 2 ปีที่แล้ว +1

    Yall are so clutch. You are saving me thousands of dollars...legit. Great videos. F*ck every BMW dealership and all these mechanics charging $900 dollars labor for literally any job, no matter how tedious.

  • @mro9466
    @mro9466 4 ปีที่แล้ว

    watching this before buying anything !

  • @temio.463
    @temio.463 4 ปีที่แล้ว +1

    This is great! I don't have the opportunity to do much diy on my car so this is nice to see what s under there.
    My e90 makes a slight ticking noise that *sounds* like its coming from the trans area but I can't really tell. It's only under acceleration though, plus no error codes. Any ideas?
    It’s a rwd.
    Also: 'Baby counter' haha! So good!

    • @fcpeuro
      @fcpeuro  4 ปีที่แล้ว

      Thanks Temi, it can be helpful sometimes to just see whats actually going on behind the scenes of your car! With no error codes that would tend to lean towards something mechanical such as some of the things discussed in this video and our E9X Suspension Diagnostics video (check it out if you havent as it may help). It can be sort of hard to tell whats wrong with just a sound though, sometimes its easier to inspect all the usual suspects visually. Under hard acceleration it could be caused my an engine or trans mount that is shot as well.

  • @sjoerdrozendaal3416
    @sjoerdrozendaal3416 3 ปีที่แล้ว +2

    Dont use your torquewrench to angle tight (ttgus torqueing more than the set torque) as you will mess up your wrench.

    • @triggahappi2732
      @triggahappi2732 2 ปีที่แล้ว +1

      I was looking at the comments hoping someone else caught it

  • @elurb7231
    @elurb7231 2 ปีที่แล้ว +1

    11:37 how do you get the wrench to stay on the bolt. The OE bolt surface is super thing, less than half the thickness of a box wrench. It keeps slipping off.

    • @fcpeuro
      @fcpeuro  2 ปีที่แล้ว

      Hi El, for this we used a box end wrench that has an offset head to help with leverage. I would suggest using something similar to that!

    • @elurb7231
      @elurb7231 2 ปีที่แล้ว +1

      @@fcpeuro yea I had box wrenches with a bit of a bevel in the inner face if the closed part which wasn't working. Bought a single wrench with less of that feature and it worked.

    • @CREAOOfficial
      @CREAOOfficial 2 ปีที่แล้ว

      @@elurb7231 hey - I have the Duralast box wrenches. This damn thing keeps slipping off. I’m assuming for the same reasons as you. What wrench did you end up buying just so I could have a reference

    • @elurb7231
      @elurb7231 2 ปีที่แล้ว

      @@CREAOOfficial just sanded the face a bit with a cut wheel/ heated and PB blaster to help the effort.

    • @cw988
      @cw988 6 หลายเดือนก่อน

      Suggestion... use a grinder to flatten the box wrench so it isn't tapered. I've done that with sockets as well.

  • @brendanedwards5487
    @brendanedwards5487 2 ปีที่แล้ว

    did this yesterday w my instructor it was calm as hell except for that cheap ass plastic 😭

  • @towhee7472
    @towhee7472 3 ปีที่แล้ว +1

    80 000 miles, lol. I'm at 180 000 miles and start to think about doing this :D By the way, I live in something like the rust belt, does soaking everything in penetrant really work?

    • @fcpeuro
      @fcpeuro  3 ปีที่แล้ว +1

      We get quite a bit of corrosion here as well, and penetrant can certainly help depending on how bad it is.

  • @stickerzfrommarz989
    @stickerzfrommarz989 5 หลายเดือนก่อน

    Where did the clutch video go?????? I just watched it now it’s gone. I’m ready to do the work n no video to recap

  • @zacharysementelli1098
    @zacharysementelli1098 3 ปีที่แล้ว

    Can I still drive it while I have everything soaking in pb blaster

    • @velocip1
      @velocip1 3 ปีที่แล้ว +1

      Yes

  • @Ie0n1
    @Ie0n1 4 ปีที่แล้ว

    Can you make one for dampers also please?

    • @fcpeuro
      @fcpeuro  4 ปีที่แล้ว

      Its on the list Leon!

  • @MickeyGlover
    @MickeyGlover 3 ปีที่แล้ว

    I just wanna do the control arms, my car has a bad lca

  • @Jawnwickkk
    @Jawnwickkk 5 หลายเดือนก่อน

    How much this job cost in labor at a shop?

  • @OxxidCZ
    @OxxidCZ 4 ปีที่แล้ว

    How many miles did this BMW have on clock?

    • @fcpeuro
      @fcpeuro  4 ปีที่แล้ว

      76k I do believe. So right about the 80k mark we expect to see these things start to all fail together.

  • @dannyed3446
    @dannyed3446 3 ปีที่แล้ว

    Do you need to align after ?

    • @fcpeuro
      @fcpeuro  3 ปีที่แล้ว

      You don't have to, but it would be a good idea!

  • @seasonedtoker
    @seasonedtoker 3 ปีที่แล้ว

    Don't hit your E90 hubs too much, they are milled aluminium, you can easily bend some tabs without noticing

    • @SaifDrives
      @SaifDrives ปีที่แล้ว

      for rwd yes, for xdrive they’re all steal . at least that’s what i just heard him say

  • @ArisArray
    @ArisArray 2 ปีที่แล้ว

    Are the struts the same

    • @fcpeuro
      @fcpeuro  2 ปีที่แล้ว

      Hey Shawn, the driver and passenger side each have their own part numbers as they are slightly different. For the most part, they are all similar across the models, the only difference being sports models vs non-sport.

  • @AlexanderSanchez-xn5jv
    @AlexanderSanchez-xn5jv 4 ปีที่แล้ว

    Clunk when accelerating, if I was to launch I would hear it from the passenger side . What could it be ? Edit: sometimes transmission tunnel

    • @fcpeuro
      @fcpeuro  4 ปีที่แล้ว +1

      Dangit Alexander stop launching your car and itll stop making that noise ;) All kidding aside it could be something mechanical such as some of the things discussed in this video and our E9X Suspension Diagnostics video. It can be hard to tell whats wrong with just a sound though, sometimes its easier to inspect all the usual suspects visually. If its only caused "if you were to launch it", it could be caused my a failed engine or trans mount as well.

    • @AlexanderSanchez-xn5jv
      @AlexanderSanchez-xn5jv 4 ปีที่แล้ว

      FCP Euro thank you .

    • @AlexanderSanchez-xn5jv
      @AlexanderSanchez-xn5jv 4 ปีที่แล้ว

      B B to have fun?!?

    • @AlexanderSanchez-xn5jv
      @AlexanderSanchez-xn5jv 4 ปีที่แล้ว

      FCP Euro do you have a video on changing motor/ transmission mounts?

    • @AlexanderSanchez-xn5jv
      @AlexanderSanchez-xn5jv 4 ปีที่แล้ว

      FCP Euro also on rare occasions on start up

  • @PreslavDodev
    @PreslavDodev 3 ปีที่แล้ว +1

    What is the total prize of this? Thanks!

    • @fcpeuro
      @fcpeuro  3 ปีที่แล้ว

      About $600 for the entire kit ! www.fcpeuro.com/products/bmw-10-piece-control-arm-kit-e90-e91-e92-e90caxdrive2?

  • @MrDanielepaolini73
    @MrDanielepaolini73 2 ปีที่แล้ว

    Che marca sono questi ricambi? Mi è successo anche alla mia E90 330xd

    • @stevenhasanbelli9881
      @stevenhasanbelli9881 ปีที่แล้ว

      Lemfoerder, dovresti riuscire a trovarli anche in Europa ma non ne sono sicuro

  • @jasoneyes01
    @jasoneyes01 3 ปีที่แล้ว +1

    "Get ready for debris to fall on you" or a dead mouse in my case.