Appke pass 2 choice he ya app active harmonics filter use Karen nehi to ITHD ka setting badha de issme apka capacitor jaldi kharap hone ka chance ho sakta he
Sir mere pas bhi ye controller lga hua h but sir vo auto me nhi ho rha auto select krne pr bhi again manual me hi dekha rha hai and perimeter bhi change nhi ho rhe h how to solve this problem
Ye channal akdam "Sidhi baat no bakwas"....Thanks a lot brother fpr sharing valuable knowledge....
Welcome 😊
Nice sir is type ka videos hum.e bhut confidence deta haan ...panel ka kam karne main...
Bahut achcha aur Knowledge Wala Video Shared Kiya aapne Thanks You❤
Welcome 😊
TQ for showing, now I have ucom alarm, mccb on condition
Very well explained 🙏
Knowledgeable person 👏👏👏👏👏
Thank you 🙏🏻 There are 8 nos of video on EtaSmart 16R, you can get deep knowledge on this if you go through all those videos
Good
Good job sir
Overcompensate A02 at no load and PF=.18
Check my part - 9 video on etaSmart controller in playlist
Over compensation fault aa raha hai please solution
I-THD valve change option not available in 16r realy pl help
Watch my part 5 and part 6 video on etasmart controller in my playlist
so good
I uploaded a playlist ( contains 7 video ) on EtaSmart 16R by watching all those video you will be master in it
Very good
Welcome 😊
Good💕
Thank you 😊
Ucom ka fault means
Under compensation matlab app ka capacitor bank Kam pad raha he / app ka capacitor bank Ka MCCB check kijiye kahin MCCB band to nai he
C t cheack kaise karte hai
Check it's back side, you can find S1 and S2 terminal and you have to trace that wire from where it's come, when you find CT then check CT ratio
The correct way, to install CT is in the main incomer breaker input side
I thd ka alarm ata hai sir
Kya apka load me jyada fluctuations he
Iss video me dikhaya hun kya kya check karna he video ko pura ache se dekhiye then kuch doubt ho to bataiye
36% ithd ata hai sir
Appke pass 2 choice he ya app active harmonics filter use Karen nehi to ITHD ka setting badha de issme apka capacitor jaldi kharap hone ka chance ho sakta he
Ocom ka alarm ata hai to sir kya kare
Appne capacitor ka value galat dala hoga
Mere playlist me APFC panel me part 3 video check Karen ussme me bataya hun ke capacitor ka value kese sehi se put kartenhen
1st check kijiye ke app ka Powerfactor ka setting low to nehi
Ok sir
Sir mere pas bhi ye controller lga hua h but sir vo auto me nhi ho rha auto select krne pr bhi again manual me hi dekha rha hai and perimeter bhi change nhi ho rhe h how to solve this problem
Please help
May be yeh software issue ho sakta he. App ko L&T customer care se baat karna hoga
@@itzelectricalsir isme Firmware version 2.23 show kr deta h
App ka load me jyada fluctuation to nehi he, agar load me jyada fluctuation hoga to fir auto program sehi se kam nehi karega
Pehle kitna load chal raha he dekhiye
Hi sir any fault coming after power panel is not working?
Jo bhi fault ayega then capacitor panel work Nehi karega
Agar wo protection hata na he to expert mode per ja kar setting karna padega
Good luck
Pf bhi .99 hai phir bhi undercom. aa rha hai
Check target Powerfactor, agar Target power factor actual se jyada hoga aur app ka sara capacitor bank active hoga toh phir undercom alarm ayega
Same problem sir targate pf.99 or actual pf.93 chal rha he alarmaa rha he kya kre sir
Konsa alarm
Ucom he sir
Toh kya app ka sara capacitor bank on he