It seems a lot of resistors can go faulty on ps3 boards. In addition, without the oscilloscope it would have been extremely difficult to find the area of the fault. It pays to have a good board around to compare values. Thank you for another excellent repair.
2:21 Sir what the resistance here should be? I get different value on all of them, 2 are around 270hm, 1 is 240 ohm and 1 is 340ohm. Console turns on for 30s and then turn off
The resistance values you're getting suggest that there may be an inconsistency or issue with one or more components in that circuit. However, the exact resistance value can vary depending on the specific circuit and components involved.
Great work! Please more video like that. To make it easier for the viewer I suggest you to show better where you are placing the probes. Sometimes is difficult to see because those components are tiny. Thanks again!
Sir I have issue with my PS3 when I try turn on my PS3 the PS3 turn on perfectly but after sometime like after 2 min shutdown automatically can I used this method for that...
recently , i was able to make short clips of your videos . so i can getting on them when ever i wanted watch a important information you mentioned . or whatch where do i probe to read voltages on test points with my multymeter. but i don't know why i can't do this on your current videos . did you close that opinion on you're youtube channel ?
@ElioFernandez Yes, it's possible. If the HDMI IC is missing or damaged on a JTP-001 board, the console could exhibit issues like no video output or failure to initialize the HDMI connection properly. The PS3 may default to AV output in some cases, but if the IC's absence disrupts other circuits, it might cause additional problems. Installing a new HDMI IC and ensuring the surrounding components are in good condition should resolve the issue. Let me know if you need help! 😊
Can you help me? I've got a PS3 Slim 3004B. It turns on and works for 10 seconds to 10 minutes. I checked all the resistances, and they are OK. What could the problem be? I think it might be the RSX, and I might need to reball it.
@Rermo416 If your PS3 Slim shuts down after a few minutes, you might be right about the RSX and the CELL. The RSX and CELL chips can sometimes lose connection with the motherboard due to thermal stress, and a re-ball might help restore stability. Before rebelling, you might want to try a reflow as a temporary test to see if it resolves the issue, though rebelling is often a more permanent solution.
Assalamu aleykum rahmetullah ve berakatu, I will ask about a malfunction. PS3 slim The problem is, I did a re-fluxing process to the processor. But I tried this without a professional BGA tool. I gradually heated the chip from 200 c to 210 c by applying flux. Now the red light on the device is fixed. When I start it, the fan is not spinning. It starts. It turns off after 20 seconds without making any beep sound. The red light goes out without any beep. There is no heating in RSX and cell. Another question I have. Professional. Unfortunately, I do not have the means to buy a tool. What should be the maximum reflow temperature of the chip with a hot air gun or station and how many minutes should it remain at that temperature on average to ensure reflow.Teşekkür ederim.
First, set the heat gun to 180 to 200 degree and preheat the whole motherboard from both sides for about 10 to 15 minutes. Then give heat both sides of the specific chip at 480 degrees for about 3 to 4 minutes. It will help not to bend the motherboard. And lowers the chance of damaging the solder pads under the BGA chip .
Its called schematics, and yeah there’s schematics everywhere most have components written down, most have just letters and numbers like R1 R5 for resistors C1 for capacitors T3 for transistors What he does is take a ps3 model that works fine and write down all capacities if u dont have a clear schematic. But since its a ps3 there’s probably a detailled one, idk why he’s lying tho, some people like to look like magicians when they’re not.
@@medmusic7977 ps3 motherboards have a lot of revisions and to be honest i have not seens any detailed schematic about ps3 or ps4 device online. I fixed my ps4 by guessing missing resistance value and applyinh ohms law in order to calculate the proper value. Not much convenient.
i have a model cech2501B, the layout seems to be different but the one measured 175 ohms here is measures 2.2k ohms on my motherboard. can you provide measurement for my model of ps3? Your videos are great help and looking forward to fixing mine. Thank you!
Hello sir thanks for all your efforts you are the only one who try to fix that problem I have the exact problem on my ps3 and i followed all your videos related with that problem i don't know how to give power to mobo so i didn't test the voltage like you did in that video but i tested every resistors you tested in those videos and are fine except two things 1 the cmos resistors you found 201 ohm and 33 ohm and mine has 4k ohm and 33 ohm (cmos battery is there) 2 the resistor you replaced in the back Risistors in mine are different order there so i kind of lost there i tested them anyway some has 2.2k some has 3.3k some has 270 ohm Any advice sir and thanks in advance
@@idreestech Sir i've checked all resistors you tested in those videos and all are fine exept some resistors and a capacitor who is removed by itself when i touched it
This issue is often related to hardware failures, such as a short circuit, power supply problem, or overheating protection. Here are a few steps to troubleshoot: Check Power Supply: Ensure the power supply unit is functioning properly. If possible, test with a known working PSU. Inspect the Motherboard: Look for any burnt components, blown capacitors, or signs of damage. Clean and Reapply Thermal Paste: Overheating can trigger shutdowns. Clean the heat sink and reapply thermal paste to the CPU and GPU. Check for Shorts: Use a multimeter to check for shorts near the power ICs or MOSFETs. If none of these work, there may be an issue with the APU (CPU/GPU combo) or syscon. In that case, more advanced repair techniques, such as reballing or replacing the chip, might be needed.
@idreestech bro red light doesn't turn into green , just goes off and fan run for 2 second and just goes off then I have to press start button again , then red light appears
It seems a lot of resistors can go faulty on ps3 boards. In addition, without the oscilloscope it would have been extremely difficult to find the area of the fault. It pays to have a good board around to compare values. Thank you for another excellent repair.
2:21 Sir what the resistance here should be? I get different value on all of them, 2 are around 270hm, 1 is 240 ohm and 1 is 340ohm. Console turns on for 30s and then turn off
The resistance values you're getting suggest that there may be an inconsistency or issue with one or more components in that circuit. However, the exact resistance value can vary depending on the specific circuit and components involved.
Great work! Please more video like that. To make it easier for the viewer I suggest you to show better where you are placing the probes. Sometimes is difficult to see because those components are tiny. Thanks again!
These are the positive pins of capacitors like 230 Mf, 470 Mf, and 330 Mf.
@@idreestech thank you sir.
@@phoenixtiger101tube U r W c
Sir I have issue with my PS3 when I try turn on my PS3 the PS3 turn on perfectly but after sometime like after 2 min shutdown automatically can I used this method for that...
It could also be due to tokkin capacitors.
recently , i was able to make short clips of your videos . so i can getting on them when ever i wanted watch a important information you mentioned . or whatch where do i probe to read voltages on test points with my multymeter. but i don't know why i can't do this on your current videos .
did you close that opinion on you're youtube channel ?
I did not do any changes dear.
Sir ji my PS3 console green light sometime then turn off solve the solution it should be really or not
Sir
Jazak Allah
Apki videos bht informative hoti hai.
Aur sekhne ko b 👍
Thanks for the visit
Hello Master! Is it possible that a JTP-001 board from a PS3 slim presents the same fault if it does not have the HDMI IC installed?
@ElioFernandez Yes, it's possible. If the HDMI IC is missing or damaged on a JTP-001 board, the console could exhibit issues like no video output or failure to initialize the HDMI connection properly. The PS3 may default to AV output in some cases, but if the IC's absence disrupts other circuits, it might cause additional problems. Installing a new HDMI IC and ensuring the surrounding components are in good condition should resolve the issue. Let me know if you need help! 😊
What would be the fair price to fix this problem mate? Here stores near me charge 4000rs to fix it
Can you help me? I've got a PS3 Slim 3004B. It turns on and works for 10 seconds to 10 minutes. I checked all the resistances, and they are OK. What could the problem be? I think it might be the RSX, and I might need to reball it.
@Rermo416 If your PS3 Slim shuts down after a few minutes, you might be right about the RSX and the CELL. The RSX and CELL chips can sometimes lose connection with the motherboard due to thermal stress, and a re-ball might help restore stability. Before rebelling, you might want to try a reflow as a temporary test to see if it resolves the issue, though rebelling is often a more permanent solution.
@idreestech Thanks, I will try!
As always successful repair from best teacher ✅❤
Glad you think so!
Assalamu aleykum rahmetullah ve berakatu, I will ask about a malfunction. PS3 slim The problem is, I did a re-fluxing process to the processor. But I tried this without a professional BGA tool. I gradually heated the chip from 200 c to 210 c by applying flux. Now the red light on the device is fixed. When I start it, the fan is not spinning. It starts. It turns off after 20 seconds without making any beep sound. The red light goes out without any beep. There is no heating in RSX and cell. Another question I have. Professional.
Unfortunately, I do not have the means to buy a tool. What should be the maximum reflow temperature of the chip with a hot air gun or station and how many minutes should it remain at that temperature on average to ensure reflow.Teşekkür ederim.
First, set the heat gun to 180 to 200 degree and preheat the whole motherboard from both sides for about 10 to 15 minutes. Then give heat both sides of the specific chip at 480 degrees for about 3 to 4 minutes. It will help not to bend the motherboard. And lowers the chance of damaging the solder pads under the BGA chip .
I have one apart now. You mention someone used the wrong paste. What is the proper paste? Would arctic silver work?
Arctic silver4 is one of the best thermal paste ever. But should be the original one.
Is there any document with all resistances written down or you figure them out by yourself?
No dear!
Its called schematics, and yeah there’s schematics everywhere most have components written down, most have just letters and numbers like R1 R5 for resistors C1 for capacitors T3 for transistors
What he does is take a ps3 model that works fine and write down all capacities if u dont have a clear schematic.
But since its a ps3 there’s probably a detailled one, idk why he’s lying tho, some people like to look like magicians when they’re not.
@@medmusic7977 ps3 motherboards have a lot of revisions and to be honest i have not seens any detailed schematic about ps3 or ps4 device online. I fixed my ps4 by guessing missing resistance value and applyinh ohms law in order to calculate the proper value. Not much convenient.
Am experiencing the same problem right now sir and I am not a repairer, the guys here can't do it, what can I do am in Ghana
It would help if you also learned to repair these consoles.
Is it possible to learn it online
@@iam_360barber_gh3 Yes.
@@iam_360barber_gh3 Yes, dear!
Ok
I have a similar issue. I have a 2.2k resistor, is it ok to use instead?
2.2 k is not the actual value. You need to check the exact value of a resistor taken down from another motherboard of the same model.
i have a model cech2501B, the layout seems to be different but the one measured 175 ohms here is measures 2.2k ohms on my motherboard. can you provide measurement for my model of ps3? Your videos are great help and looking forward to fixing mine. Thank you!
Please tell the motherboard number like JSD-001 or something like that.
@@idreestech yes it is jtp-001
@@idreestech hi! can you help me find oit whats wrong with my board
brother you are amazing ...god bless you plz continue
Thank you so much 😀
I have the same issue. Can you repair it?
I hope so.
@@idreestech how can I send it to you?
@@umerjaved7016 Check the description, please.
Hello sir thanks for all your efforts you are the only one who try to fix that problem
I have the exact problem on my ps3 and i followed all your videos related with that problem i don't know how to give power to mobo so i didn't test the voltage like you did in that video but i tested every resistors you tested in those videos and are fine except two things
1 the cmos resistors you found 201 ohm and 33 ohm and mine has 4k ohm and 33 ohm (cmos battery is there)
2 the resistor you replaced in the back
Risistors in mine are different order there so i kind of lost there i tested them anyway some has 2.2k some has 3.3k some has 270 ohm
Any advice sir and thanks in advance
All looks fine. So dear may be some other error. Please watch more according to your machine errors.
@@idreestech thanks sir
I did i'll rewatch them maybe i missed somthing
@@idreestech Sir i've checked all resistors you tested in those videos and all are fine exept some resistors and a capacitor who is removed by itself when i touched it
Can i send you some pictures on facebook if that is ok
@@younes1412 OK
When i turn on my ps3 slim , red light doesn't turn green , just goes off and instantly shutdown after 2 second with beep sound
Can anyone suggest???
This issue is often related to hardware failures, such as a short circuit, power supply problem, or overheating protection. Here are a few steps to troubleshoot:
Check Power Supply: Ensure the power supply unit is functioning properly. If possible, test with a known working PSU.
Inspect the Motherboard: Look for any burnt components, blown capacitors, or signs of damage.
Clean and Reapply Thermal Paste: Overheating can trigger shutdowns. Clean the heat sink and reapply thermal paste to the CPU and GPU.
Check for Shorts: Use a multimeter to check for shorts near the power ICs or MOSFETs.
If none of these work, there may be an issue with the APU (CPU/GPU combo) or syscon. In that case, more advanced repair techniques, such as reballing or replacing the chip, might be needed.
@idreestech bro red light doesn't turn into green , just goes off and fan run for 2 second and just goes off then I have to press start button again , then red light appears
My ps3 slim is doing the exact same thing. I wish you were close by because I would bring my ps3 to you for repair.
I wish sir u were in India i have multiple ps3 slim which are dead and i showed it to repair guys here they won't able to fix it :'(
th-cam.com/video/pI44qt_EHQ8/w-d-xo.html
Try them by yourself, dear.
Very nice sirji aap ka tarika la jabab sirji.
Great work! Please more video!
More to come!
Man, you are amazing!
Sir i was ps3 which i use after 1 year and that a response of my ps3
Check for an SMD resistor that has deteriorated its value.
EXCLLENT WORK ...
HOW KNOW VALUE OF RESISTOR ...YOU HAVE SCHAMTIC?
No.
@@idreestech YOU COMPARE RESISTOR FROM ANTHOR PS3 ?
good work
Thanks for the visit
Perfect master
Welcome 👍
thank you for this expierience)
Welcome 👍
@@idreestech waiting for your next video)
Good work
Thank you! Cheers!
Thanx 😀 master
Welcome 👍
very good job
Thank you! Cheers!
👍🇮🇳🙏
Welcome 👍