This is the tutorial.I have been looking all over the web for... How to power my accessories through the ignition. I am adding a GPS speedometer odometer.
I would really like to see the diagram of how yours is all wired up….. i wired mine up just how your picture shows but my bottom master switch light stays on all the time. Im so confused im very dumb when it comes to all this wiring
Clean job man! I want to power my remaining switches from one switch , same as you did. Can you provide how you wired that setup from main to rest of switches?
Great video. I’m doing this now in my sxs. When hooking up accessories it’s obvious how to hook power and ground to fuse block, but what about hooking ignition up to the accessory switches? Do I need to tie each accessory switch into the hot wire off the cig lighter?
I know most switches can only handle 12-24 volts at 20 amps, so do you think it's a good idea to use a flyback diode to prevent "back EMF" from possibly damaging your master switch? I plan on using the 1N4007 Rectifier Diode myself.
No but I can make one. I just picked up a second Teryx awhile back and have to do a full install of everything on it so I can do a video step by step. I just ordered all the Rock Lights, Whip It's, Lights Bar, and Sound System, as well as back up lights, and winch. I'll keep you posted when the video is up.
Did you ever do another video? I couldnt find it if you did.. would still be really helpful just showing wiring the lightbar to teh fuse box and the switch
Can I add my turn signal relay after the fuse block and use a positive and ground from the fuse block to power said relay. I know I'll then have another ground coming from the switch
You wire the lights together,positive to positive,negative to negative,then run those to your switch,then run your wires to your fusebox,with the appropriate fuse rated for your lights.
I have watched your tutorial over and over you have made it so simple but my question is I was wanting my stereo rocker switch to have power when sxs is turned off but not the other switches How could I do that
Thanks so much I had a 2017 T4 and I was wanting to put rocker switches in it but really never knew how ended up selling it I wish I had kept it those are good machines, I have a rhino now and that's what I'm putting my rocker switches in, and another question do you run a ground from you switches to what ever your hooking up to lights or what ever it may be
one last question,is 10g wire is ok to use on the battery to fuse block . and one lasting is If I can use lower relay ? would it be ok to use 80amp relay? I'm familiar with all the wiring it's just the power calculations that I'm not. So what I'm trying to add on mine is 2 sets of fog lights has their own switch separately and a stereo system plus phone charger
Depends on the stero size but I would try run 8 gauge or lower but you can probably get away with 10 gauge. Lights are probably led and will use low power.
@@GrayHairedDad Hello Brandon sorry for asking to much questions,its just i don't know how to do the math which relay and the inline fuse? how would I know what amps of the relay and the inline fuse? I've seen a lot of videos using only 40mps both on this 100amp fuse box and i think that was wrong! and I've seen other videos using relays of each accessory maybe this is good but only if you have room but i like how you did yours because i have no room to put each accessory? it's just i don't know what amps
@@GrayHairedDad For your example, as long the accessories don’t pass up that 120 amp relay it should be fine right? So for an example if I was to set up 5 light bars and they each run 20 amps I would have 100 amps out of that fuse box. But that 120 amp relay is doing the work for those 5 light bars not the 20 amp rocker switches. Right?
So I left the fuse out but the manual calls for it. So to be on safe side you should run a 100Amp fuse. This what you can use M1A2 Circuit Breaker Switch 100A Waterproof Fuse Inline Holder 3-15 AWG Resettable Fuse Manual Reset 12V-48V DC for Car Audio Sound Amplifier System RV Home Marine Boat Truck a.co/d/gH5MP5I
@@GrayHairedDad thank you! i'm setting my T4 just like you have it. i like the idea of being able to control power to ACC without having to have the key. great work!
This is the tutorial.I have been looking all over the web for... How to power my accessories through the ignition. I am adding a GPS speedometer odometer.
I would really like to see the diagram of how yours is all wired up….. i wired mine up just how your picture shows but my bottom master switch light stays on all the time. Im so confused im very dumb when it comes to all this wiring
Can you make up that wiring diagram and show us that? Im currently trying to do the same type of setup with my teryx
Clean job man! I want to power my remaining switches from one switch , same as you did. Can you provide how you wired that setup from main to rest of switches?
Great video. I’m doing this now in my sxs. When hooking up accessories it’s obvious how to hook power and ground to fuse block, but what about hooking ignition up to the accessory switches? Do I need to tie each accessory switch into the hot wire off the cig lighter?
No your tie the cig outlet to the relay. When the relay is powered it powers the fuse block resulting in you accessories having power.
@@GrayHairedDad got it. Thanks!!
Nice job of explaining this! Thanks!
I know most switches can only handle 12-24 volts at 20 amps, so do you think it's a good idea to use a flyback diode to prevent "back EMF" from possibly damaging your master switch?
I plan on using the 1N4007 Rectifier Diode myself.
Not a bad idea at all. Would help protect it.
Do you have a video to show you wiring in an accessory to that Fuze block and getting back lights to come on on switches
No but I can make one. I just picked up a second Teryx awhile back and have to do a full install of everything on it so I can do a video step by step. I just ordered all the Rock Lights, Whip It's, Lights Bar, and Sound System, as well as back up lights, and winch. I'll keep you posted when the video is up.
Yup if you could make a video showing the connections from accessory to switch to fuse box. That would be helpful thank you
I will work on that and let you know when it's ready for viewing.
Did you ever do another video? I couldnt find it if you did.. would still be really helpful just showing wiring the lightbar to teh fuse box and the switch
If I'm running it from my cig what 100 amp fuse is needed. Is that just a red wire from the relay to the battery with a 100 amp fuse in the middle?
Just a 100 Amp fuse between the battery and relay.
Can I add my turn signal relay after the fuse block and use a positive and ground from the fuse block to power said relay. I know I'll then have another ground coming from the switch
What size wire did you run from battery to fuse block?
8 gauge
Great video I'm glad I found it, i was wanting to add two lights on the back of my rhino how do I wire both of them up to work on one rocker switch
You wire the lights together,positive to positive,negative to negative,then run those to your switch,then run your wires to your fusebox,with the appropriate fuse rated for your lights.
I have watched your tutorial over and over you have made it so simple but my question is I was wanting my stereo rocker switch to have power when sxs is turned off but not the other switches How could I do that
Short answer is, run a fused protected power wire from the battery to your stereo rocker switch.
Long answer, Would have to make a video.
Thanks so much I had a 2017 T4 and I was wanting to put rocker switches in it but really never knew how ended up selling it I wish I had kept it those are good machines, I have a rhino now and that's what I'm putting my rocker switches in, and another question do you run a ground from you switches to what ever your hooking up to lights or what ever it may be
Need video on adding 12volt accessories on my 48volt Intermidator EV.
can you add a buss bar between the relay and the fuse box ?
I don't see why not.
what is the amper of the relay . the relay that power up the fuse box
120Amp. They make a 200Amp for little more $. I got it off Amazon.
thanks man thanks for responding right away. I like the way you explained it ! very detailed 👍👌
one last question,is 10g wire is ok to use on the battery to fuse block . and one lasting is If I can use lower relay ? would it be ok to use 80amp relay? I'm familiar with all the wiring it's just the power calculations that I'm not. So what I'm trying to add on mine is 2 sets of fog lights has their own switch separately and a stereo system plus phone charger
Depends on the stero size but I would try run 8 gauge or lower but you can probably get away with 10 gauge. Lights are probably led and will use low power.
@@GrayHairedDad Hello Brandon sorry for asking to much questions,its just i don't know how to do the math which relay and the inline fuse? how would I know what amps of the relay and the inline fuse? I've seen a lot of videos using only 40mps both on this 100amp fuse box and i think that was wrong! and I've seen other videos using relays of each accessory maybe this is good but only if you have room but i like how you did yours because i have no room to put each accessory? it's just i don't know what amps
Did you make the other video connecting accessory from switch to fuse box ? thanks for this video its a big help.
Not yet sorry. I just bought a 2nd Teryx so I need to do all the wiring on it and I will do a full video on it.
Great video thank for all your details
Nice explanation on the video. Quick question would each run off of the fuse block need to have a relay too?
It depends on your switch and how many amps it can handle. Most rocker switches are rated up to 20amps at 12v.
@@GrayHairedDad Thanks for the quick reply
Anytime. Let me know if I can help with anything else.
@@GrayHairedDad For your example, as long the accessories don’t pass up that 120 amp relay it should be fine right? So for an example if I was to set up 5 light bars and they each run 20 amps I would have 100 amps out of that fuse box. But that 120 amp relay is doing the work for those 5 light bars not the 20 amp rocker switches. Right?
Correct
what "100 AMP Fuse" did you use?
So I left the fuse out but the manual calls for it. So to be on safe side you should run a 100Amp fuse.
This what you can use
M1A2 Circuit Breaker Switch 100A Waterproof Fuse Inline Holder 3-15 AWG Resettable Fuse Manual Reset 12V-48V DC for Car Audio Sound Amplifier System RV Home Marine Boat Truck a.co/d/gH5MP5I
@@GrayHairedDad thank you! i'm setting my T4 just like you have it.
i like the idea of being able to control power to ACC without having to have the key.
great work!
Thanks
Can you make a video coming off a bus bar? I would greatly appreciate it.