I just oiled the ring around where you loosen the nut to take the clutch off and it worked to stop the noise and the stalling. I also had to move the engine forward to tighten the chain along with that tensioner adjusted. The chain out the box was way too loose. Now its running great the past 2 straight days. But I’m aware I’ll get to the point I will have to take that clutch off and do that maintenance you showed. My fix is temporary but works without having to remove the clutch.
Going to be doing it monthly?........more like weekly 😂. I got the clutch off and it's fine but it's the rod the clutch slides onto that isn't able to slip and is doing similar problems like making a grinding noise taking off on it's own then shutting off
Logan Stewart the bar my clutch slides onto isn't slipping properly. I put the clutch on and try to spin it and it spins but before it completes the rotation it's starts getting harder to twist then after the full rotation it breaks free from it's lock up so I need once then goes back to getting harder to rotate.
Just bought a mini bike and I only took it out twice and has the problems you described, takes off on it's own and weird noise! So if I grease the clutch, it should stop? How is it I already have a problem with clutch?
I tried it's not the clutch. Mine has the same problems after one week of buying it and 6 times riding it around. I believe it is bad plates that are being used or the spin is faulty. Damn and I was thinking about getting the 500$ one after the experience with the 80cc. This time I'll get a warranty on a it and have the clerk service it because they asked last time and I said no thanks
does any one know whats wrong when i pull the rope the clutch wont spin and when it happened i was giving it about full throttle and it started smoking for like 20 seconds and it woudnt start
We have an 80 cc Motovox mini bike. Runs and turns the wheel fine as long as there is no weight on it. I do not feel like the clutch is slipping, because the motor does rev up like ir should when you try to take off on it like I think it would if the clutch was slipping. I have adjusted the governer and throttle. Makes very little, if any difference. Bad governer? Carb need more thurough cleaning?
I have decided to take the clutc off to clean it. This bike has been sitting for a while. Thinking the clutch is stuck and not letting the engine rev high enough to pull any weight. Make sense? Now if I can just find a way to get to the nut in the other side of chsin guard near the rear wheel.
quick question on my motovox10 mini bike , when I pull my pullstart to start up my bike my chain and backtire are running basically when I pull my pullstart to start bike it trys to take off and I'm not even touching the throttle or giving it speed so I don't know why when I pull pullstart my chain and tire is running, someone help me fix this please ?!
+Zander Shawongonabe the clutch shaft is grabbing, bcs it's dry. remove clutch and grease the shaft also you can sand the contact surface of the shoes with fine grit sandpaper
They do when you only wax it in your garage and crank it up to hear it idle. They do when you only putt putt around in a parking lot. Any other use and those SOBs get rust welded on there.
These only get seized up due to improper or lack of maintenance. Best practice is to use anti seize on the output shaft before you install the clutch assembly. Problem prevented, problem solved.
![Ep.2 เบสไวน์ รวมคลิปฮา SS4 - [ พากย์นรก ]](http://i.ytimg.com/vi/Ihk-LzEbox0/mqdefault.jpg)
Best clutch maintenance vid I have seen .
Hey thanks for the vid man.. We LOVE our MBX10.. Fun for the whole family! Great product great price!
I just oiled the ring around where you loosen the nut to take the clutch off and it worked to stop the noise and the stalling. I also had to move the engine forward to tighten the chain along with that tensioner adjusted. The chain out the box was way too loose. Now its running great the past 2 straight days. But I’m aware I’ll get to the point I will have to take that clutch off and do that maintenance you showed. My fix is temporary but works without having to remove the clutch.
Muy buen video aún cuando no se inglés, con las imágenes es muy claro.
Thank you so much. Great explanation of why this needs to be done and how often. 👏👍🙏
Is there two different styles of cliches? I took the snap ring off and it did not slide right off
I have a doubt
I dropped the screw that stops the clout plate, what size screw does it have or how do I get it
After I take the ring off the shell doesn't slide off . What do I do ??
do a vid on how to replce the chain
Going to be doing it monthly?........more like weekly 😂. I got the clutch off and it's fine but it's the rod the clutch slides onto that isn't able to slip and is doing similar problems like making a grinding noise taking off on it's own then shutting off
The little bar that the clutch slides on. Mines got a chip in the side of the shaft. Will that effect the bike. Do i have to get a new motor
Logan Stewart the bar my clutch slides onto isn't slipping properly. I put the clutch on and try to spin it and it spins but before it completes the rotation it's starts getting harder to twist then after the full rotation it breaks free from it's lock up so I need once then goes back to getting harder to rotate.
my doodle bug turns on but it wont stay on it dies out within 5sec what do i do
Tengo una moto como el vídeo que no arranca tiene chispa y gas que otra cosa puedo chegar
Hi i am having a lot of trouble taking off the clutch because i can not get it to hold in place while i loosen the bolt. Any ideas?
if you use an impact gun it should come right off. if not then you should have some one pull on the starter rope as you take it off.
Tap the wrench , with a hammer , to break the hold . And hit shock it to tighten ..😛
Just need to know what kind of oil
Just bought a mini bike and I only took it out twice and has the problems you described, takes off on it's own and weird noise! So if I grease the clutch, it should stop? How is it I already have a problem with clutch?
Bent Truth & Twisted Lies if you grease it it should stop.. and the motovox company sucks at installment so the clutch its self is like 2 dollars
I tried it's not the clutch. Mine has the same problems after one week of buying it and 6 times riding it around. I believe it is bad plates that are being used or the spin is faulty. Damn and I was thinking about getting the 500$ one after the experience with the 80cc. This time I'll get a warranty on a it and have the clerk service it because they asked last time and I said no thanks
Buenas noxhes una pregunta como puedo quitar el magneto
Where to get the masterlink
does any one know whats wrong when i pull the rope the clutch wont spin and when it happened i was giving it about full throttle and it started smoking for like 20 seconds and it woudnt start
that's what happen to mine did you fix yours?
Steve, are you still with Motovox?
Will this work pretty much on all mini mikes?
very similar across all centrifugal clutches. grease the clutch Idler shaft. this is where the squeal noise comes from and why it grabs at low rpm
-what about if u dont have the grease that u have what can i use instead
I would use stp even if I had the grease, Put stp on chain and loosened it. Lot of power now.
Sir how to fix clutch wire
Having trouble taking the clutch off the screw is off but clutch wont move
if it's stuck on the shaft, you have to use a gear puller
What's it mean if it won't go barley pulled my 7 yr old weighs about 60 pounds
We have an 80 cc Motovox mini bike. Runs and turns the wheel fine as long as there is no weight on it. I do not feel like the clutch is slipping, because the motor does rev up like ir should when you try to take off on it like I think it would if the clutch was slipping. I have adjusted the governer and throttle. Makes very little, if any difference.
Bad governer? Carb need more thurough cleaning?
I have decided to take the clutc off to clean it. This bike has been sitting for a while. Thinking the clutch is stuck and not letting the engine rev high enough to pull any weight.
Make sense?
Now if I can just find a way to get to the nut in the other side of chsin guard near the rear wheel.
quick question on my motovox10 mini bike , when I pull my pullstart to start up my bike my chain and backtire are running basically when I pull my pullstart to start bike it trys to take off and I'm not even touching the throttle or giving it speed so I don't know why when I pull pullstart my chain and tire is running, someone help me fix this please ?!
Maybe ur chain is too tight my friend had a similar problem
have you tried adjusting the idle on your carburator?
+Zander Shawongonabe the clutch shaft is grabbing, bcs it's dry. remove clutch and grease the shaft also you can sand the contact surface of the shoes with fine grit sandpaper
What is that motor? Is it the 79cc Lifan motor?
Looks like the same motor that came on my PhatMoto
No tranca mi moto es como la que están preparando en nel video
Can't hear
Lube it every couple of days, it'll never make it a month, better yet upgrade to a quality clutch, throw the no name clutch in the trash.
my moto vox mbx 10 was in storage for a while and now it just won't budge to start at all HELP PLEASE
Is there new fuel or the old fuel in it? if old replace it with new also just keep trying it may just need to warm up
thanks
me salvaste el culo de pagar 1000$ dollars
In. Español
Plis sir
THE CLUTCH WILL SLIP RIGHT OFF!....BULLSHIT!
They do when you only wax it in your garage and crank it up to hear it idle. They do when you only putt putt around in a parking lot. Any other use and those SOBs get rust welded on there.
These only get seized up due to improper or lack of maintenance. Best practice is to use anti seize on the output shaft before you install the clutch assembly. Problem prevented, problem solved.
The only thing you need to do with that POS engine is throw it away. Those things are garbage