Clever tricks with forstner bits
ฝัง
- เผยแพร่เมื่อ 8 ธ.ค. 2021
- These tips and tricks will help you bet more from your forstner bits.
▼EXPAND THIS SECTION FOR MORE RESOURCES RELATED TO THIS VIDEO▼
Tools used in this video:
Fisch Forstner Bits: amzn.to/2tvzbJg
More links to check out:
-More videos on our website: stumpynubs.com/
-Subscribe to our e-Magazine: stumpynubs.com/browse-and-sub...
-Check out our project plans: stumpynubs.com/product-catego...
-Instagram: / stumpynubs
★THIS VIDEO WAS MADE POSSIBLE BY★
Fisch Forstner Bits: amzn.to/2tvzbJg
Fisch Drill Bits: amzn.to/2BHJLl4
Please help support us by using the link above for a quick look around!
(If you use one of these affiliate links, we may receive a small commission)
★SOME OF MY FAVORITE CHEAP TOOLS★
-123 Blocks: lddy.no/vpij
-Mechanical Pencils: amzn.to/2PA7bwK
-Lumber pencil: amzn.to/2QtwZjv
-Pocket Measuring Tape: amzn.to/2kNTlI9
-Irwin Drill Bit Gauge: amzn.to/2AwTkQg
-Nut/Bolt/Screw Gauge: amzn.to/2CuvxSK
-Self-Centering Punch: amzn.to/2QvbcrC
-Self-Centering Bits: amzn.to/2xs71UW
-Angle Cube: lddy.no/10nam
-Steel Ruler: lddy.no/10mv7
-Utility knife: amzn.to/3nfhIiv
-Center-Finding Ruler: lddy.no/10nak
-Bit & Blade Cleaner: amzn.to/2TfvEOI
-Digital depth gauge: amzn.to/3mwRf2x
-Wood Glue: amzn.to/3mqek6M
-Spade Bits: amzn.to/3j8XPtD
★SOME OF MY FAVORITE HAND TOOLS★
-Digital Caliper: amzn.to/384H1Or
-Marking Gauge: lddy.no/10muz
-Marking knife: lddy.no/10mv0
-Narex Chisels: lddy.no/sqm3
-Stanley Sweetheart Chisels: amzn.to/3y5HDOc
-Mini Pull Saw: amzn.to/2UEHBz6
-Gent Saw: lddy.no/ss2x
-Coping saw: amzn.to/2W7ZiUS
-Shinwa Rulers: lddy.no/zl13
★SOME OF MY FAVORITE POWER TOOLS★
-Miter Saw: amzn.to/3gqIlQ8
-Jointer: amzn.to/3yc3gfZ
-Planer: amzn.to/3mn6BGF
-Router: amzn.to/3grD22S
-Sander: amzn.to/3DdvD0Y
-Cordless drill: amzn.to/3D9ZiIm
-Brad nailer: amzn.to/3gsRkjH
-Mini Compressor: amzn.to/3mvrmQr
-Bladerunner: amzn.to/2Wl0TtJ
-Jig Saw: amzn.to/3zetTBY
-Scroll Saw: amzn.to/3gq9qDc
-Multi-Tool: amzn.to/3muZuMi
★SOME OF MY FAVORITE OTHER TOOLS★
-Drill Bits: amzn.to/3B8Ckzh
-Forstner Bits: amzn.to/3kk3wEI
-Shop Vacuum: amzn.to/2Wkqnbl
-Machine Setup Blocks: amzn.to/3gq7kDh
-Counter-Sink Bit: amzn.to/37ZukUo
-Featherboard: amzn.to/3DeqHsq
-ISOtunes Hearing Protection (Save $10): bit.ly/3BHYdH7
(If you use one of the affiliate links above, we may receive a small commission) - แนวปฏิบัติและการใช้ชีวิต
These tips and tricks will help you bet more from your forstner bits.
▼EXPAND THIS SECTION FOR MORE RESOURCES RELATED TO THIS VIDEO▼
*Tools used in this video:*
Fisch Forstner Bits: amzn.to/2tvzbJg
*More links to check out:*
-More videos on our website: stumpynubs.com/
-Subscribe to our e-Magazine: stumpynubs.com/browse-and-subscribe/
-Check out our project plans: stumpynubs.com/product-category/plans/
-Instagram: instagram.com/stumpynubs/
★THIS VIDEO WAS MADE POSSIBLE BY★
Fisch Forstner Bits: amzn.to/2tvzbJg
Fisch Drill Bits: amzn.to/2BHJLl4
*Please help support us by using the link above for a quick look around!*
(If you use one of these affiliate links, we may receive a small commission)
★SOME OF MY FAVORITE CHEAP TOOLS★
-123 Blocks: lddy.no/vpij
-Mechanical Pencils: amzn.to/2PA7bwK
-Lumber pencil: amzn.to/2QtwZjv
-Pocket Measuring Tape: amzn.to/2kNTlI9
-Irwin Drill Bit Gauge: amzn.to/2AwTkQg
-Nut/Bolt/Screw Gauge: amzn.to/2CuvxSK
-Self-Centering Punch: amzn.to/2QvbcrC
-Self-Centering Bits: amzn.to/2xs71UW
-Angle Cube: lddy.no/10nam
-Steel Ruler: lddy.no/10mv7
-Utility knife: amzn.to/3nfhIiv
-Center-Finding Ruler: lddy.no/10nak
-Bit & Blade Cleaner: amzn.to/2TfvEOI
-Digital depth gauge: amzn.to/3mwRf2x
-Wood Glue: amzn.to/3mqek6M
-Spade Bits: amzn.to/3j8XPtD
★SOME OF MY FAVORITE HAND TOOLS★
-Digital Caliper: amzn.to/384H1Or
-Marking Gauge: lddy.no/10muz
-Marking knife: lddy.no/10mv0
-Narex Chisels: lddy.no/sqm3
-Stanley Sweetheart Chisels: amzn.to/3y5HDOc
-Mini Pull Saw: amzn.to/2UEHBz6
-Gent Saw: lddy.no/ss2x
-Coping saw: amzn.to/2W7ZiUS
-Shinwa Rulers: lddy.no/zl13
★SOME OF MY FAVORITE POWER TOOLS★
-Miter Saw: amzn.to/3gqIlQ8
-Jointer: amzn.to/3yc3gfZ
-Planer: amzn.to/3mn6BGF
-Router: amzn.to/3grD22S
-Sander: amzn.to/3DdvD0Y
-Cordless drill: amzn.to/3D9ZiIm
-Brad nailer: amzn.to/3gsRkjH
-Mini Compressor: amzn.to/3mvrmQr
-Bladerunner: amzn.to/2Wl0TtJ
-Jig Saw: amzn.to/3zetTBY
-Scroll Saw: amzn.to/3gq9qDc
-Multi-Tool: amzn.to/3muZuMi
★SOME OF MY FAVORITE OTHER TOOLS★
-Drill Bits: amzn.to/3B8Ckzh
-Forstner Bits: amzn.to/3kk3wEI
-Shop Vacuum: amzn.to/2Wkqnbl
-Machine Setup Blocks: amzn.to/3gq7kDh
-Counter-Sink Bit: amzn.to/37ZukUo
-Featherboard: amzn.to/3DeqHsq
-ISOtunes Hearing Protection (Save $10): bit.ly/3BHYdH7
(If you use one of the affiliate links above, we may receive a small commission)
Thanks for the great video stumpy
^ typo alert - “get” more
In case nobody has said it yet: yes please, do make a video on the different uses of hole saws, spade, and forstner bits.
I just discovered you and your channel. You are excellent and very precise on your descriptions.
Love what you do.
Do you have a video in sharpening any of your metal tools?
Thank you sir for your time.
@@kevincranford148 If you go to my main channel page and scroll down, you will find a playlist full of sharpening videos. th-cam.com/channels/stwpLSByklww1YojZN-KiQ.html
No woodwork channel I've seen to date can compress as much practical value into ~5 minutes with such articulate commentary yet still be so enjoyable to watch. Please keep this format!
You put it well. Following this guy.
Agreed. The skill and experience in both woodworking and video making to achieve this is astounding.
I wish to every interested versatile craftman to receive at least partly the amount of cool/cewl tools tightly described in a hard to deny manner by stumpy nubs, if not in life, maybe in heaven. Which craftman doesn't dream of having a hall or hangar assorted (to be asserted?) with everything wanted to realize an own minded concept, instead of having to use tool sets hardly gotten spared as if the craftman is supposed to chant with remnants. Not really wanting to mention all the tool and similar stuff not or hardly available anymore (if the devils cave shall remain unscathed). So where would we get the money from not being able to be devotive "tool monks" as beings with two legs with a still pumping heart?
You can pre-drill a pilot hole with a 1/16” or 1/8” twist bit, then run the Forstner bit in halfway from each side. No tear-out. Perfect matches every time.
Nice idea. I see the small 1/8 bit makes a hole perfect for the point on the Forster to line up 👍👌🏻
I arrived at the same principle when i had to use hole saws for material too thick for the capacity of the hole saw. It really works well!
I have been using this method for years. Never fails me.
Good idea, I will probably add that with handhold drilling it is quite important to pre-drill the hole perfectly right-angle - or the top and bottom main holes will not match.
Good tip.
Always very good information. But an additional reason I love this channel is that you don't waste my time with a stupid themed lead-in, and your calm and peaceful narration is just icing on the fantastic cake!
Keep doing what you do!
That's exactly what I like about him! You don't have to put on a long, sensational show to be sensational -- on the contrary.
This channel is fast becoming my absolute favourite little corner of the internet. More great tips!
I agree !
Forstner bits also work great for coring cabbages when making sour heads or sauerkraut!
But I can't figure how to hold the head of cabage steady under the drill press. 😁😁
Remind me never to eat at your house. . Sauerkraut a-la motor oil.
I'm a little embarrassed at how much this gentleman has taught me after 15 years of carpentry. Granted, I spent 11 of them as a military reservist. This guy is a go to for a lot. Keep it goin Stump
Never too old to learn new things!
You're like the woodworking equivalent to Technology Connections and I love it. Both of you are clearly passionate, relaxed, and just seem happy to be sharing what you love. Even your backgrounds remind me of each other.
I also watch both, good stuff
Awesome tips, I hadn't thought of using tape like that and I really liked the last one re: stepping the bit size up from the other side of the board, thanks!
Would this not risk blowout on the backside on the second pass?
@@Night56Owl Was just thinking about that, and have a solution in mind:
1. Start the original hole with the larger bit, go just ~1 mm deep or so.
2. Switch to the smaller bit and go almost through, just the tip.
3. Use the larger bit to finish the hole from the opposite direction - this hole will then meet the starter hole from step 1.
You need to be careful in step 2, though. If the center thingies of the bits are not equal size, auto-centering the smaller bit may not be as accurate as you'd think.
@@veikkoimmonen7300 Another way to do it would be to use the smaller bit until the tip protrudes, then cover the entry hole with tape. Drill through from the other side until the tip pokes a hole in the tape. Finish from the tape side.
Another tip: Drill with a small bit (2 mm), and then can drill with the foster bit on each side, so you dont have to use the foster bit to the bottom until it appears to the other side (that us dificult to do, normally oneself pass all the wood to the other side), but with the small hole, you can easily stop drilling one half and flip it and drill from the other face of the piece of wood.
Or us the 2mm bit to punch through after you've drilled part way with the FORSTNER bit. You have the indent right there in the center of the whole. Good video! My first one. Pure information. No muss no fuss.
_
I recently had a project that required seventeen 2" holes drilled in 3/4 plywood. After blowing out the first few holes, I did the following: Drilled a small pilot hole, 2" forstner just over halfway through, Flip the work over and drill a 3/4" hole from the center on the backside, Use a flush cut router bit from the backside. This kept my bit and drills cooler as rotating between tools gave them time. The backsides never blew out, and I had nice clean holes on both sides.
I greatly appreciate that you always seem to make a video just before I start a new project that answers the problems I run into.
I watch EVERY one of your videos! Always learning something new. Your delivery style is excellent.
Your the one who sold me on Fisch bits. I waited for a sale and bought a whole set. They are the best bits I have ever used. If anyone is on the fence, just get them and make smooth holes already.
“You can make a hole video about when to use one or the other”
Bravo! 😂🎉
James you're amazing with all I continue to learn from you. Thank you!
I love the tips on re-boring with larger bits. Thank you for sharing. Have a great day and stay safe.
thanks! re-boring was a pain for me, live and learn
Legend! James, yet again I come away with at least 3 new tricks or tips from your channel. I watch for notifications eagerly every day waiting for your next posting! I cannot thank you enough for these - they are changing my skills and ability dramatically. I especially love Cool Tools and these tips/tutorials. Brilliant work! Thank you!
Your tips are never dull.
Excellent! I bought a set without knowing about the different types, glad I happened upon one with waves.
I learn something new every time I watch your tutorials. Thanks again and again.
Fisch forstner bits are excellent.
Right after I first saw a video about them on this channel, I purchased one to try them out.
It's been years now, and there's never been any tear-out at all with the wave-cutters I bought.
Thanks again James for the recommendation - and I definitely agree, everyone should try Fisch.
And like James, I still use spade bits, but only for drilling in used wood (that may contain nails or when I drill holes through the ceiling).
Note: They have different types of forstner bits; apart from the cutter type, they have different shank and tip types as well.
Thank you! I just bought a set of forsners bits and cannot wait to try them out.
Love your work. Thank you for another incredible lesson.
Thank you for including the chart! Will definitely make use of that.
Condensed and valuable information with perfect illustrating pictures and calm voice in modest narration - thank you so much!
Always great tips. Thanks.
Thank you very much. Many things I didn’t know! Love it.
Keep it coming. Your tips are great!
I especially like the one of using a smaller Forstner predrilled hole, and then finishing with the bigger bit.
The tape trick to bore a larger hole is outstanding! I've struggled with this in the past and almost always messed it up, requiring a redo of the entire part. Thanks!!!
I find your cometary informative as a finishing carpenter with forty plus years of experience I appreciate your clear consistency of explaining many different applications having trained a number of apprentices I find it good to use your videos as reference
So many useful tips, thanks!
Thanks for the tips. Now I’ll be using my Forstner bits more intelligently. I appreciate the succinct style of presentation without distracting background music.
Great tips! The tips for drilling larger holes, especially the tape trick, were genius!
Thank you. Some very helpful tips.. Much appreciated.
Just got a set for my birthday. Thanks for the tips, James!!!!👍👍👍👍👍
Excellent video on forstner bits. Thank you.
Agree with everything you said James. I do a lot of drilling with Forstners and I like the toothed one as I can easily sharpen it.
These videos never disappoint…thank you
I am not a pro but to me I would keep my fingers away from that drill bit. You give great safety tips all the time.
I agree fingers only an inch away, try that with a 3” bit and small piece of ply.
Ply spins fingers get grabbed by bit, messy.
Holdown clamp on drill press as you would use for drilling sheet metal.
Thank you for your humble and always interesting videos. I really like your effective and timely suggestions!
More great tips, James. Thanks.
This video is super useful, especially the tips in the last half covering how to enlarge holes and also the tips about using them in a hand drill. Thanks so much!
Thanks, some welcome advise for Forstner bits.
Thank you... great tips for an absolute beginner...
Love the info and love the format. Keep it coming!!!!
Always solid information from your channel, thanks!
Great video. Your forstner bit sharpening video a while back was great too! Brought my old hand-me-down bits back to life
Thanks for this excellent video!
Excellent tips. Well done and thank you!
Did not know there was this much to learn and know about forester bits. Thanks for sharing.
The most clever tips are usually the most simple. Thanks!
Such a great video. Most definitely grateful
Really great tips. Thanks!
I really enjoy these short videos! I always learn from them. Professional information that helps us !!
Another awesome tip from the Master Thanks 👍🏻
Very timely, Mr. The Nubs! I just inherited a box of forstner bits. Thank you, kindly.
Great video. Your material is always presented so logically and clearly.
Thanks James.
Fabulous video. 100 points. Thanks.
Brilliant! Thank you so much 🙏
Perfect timing! I’ve been working on a project that needs several large-ish holes and having some troubles hand drilling with my Forstners (don’t have a drill press). This gives me a couple ideas to try (including possibly ordering a wavy bit). As always, thanks for the tips!
Nice video filled with practical tips - thanks!
Always great info.
Great tips as always. Thank you.
Some very handy tips many thanks for sharing.
Great guidelines, Stumpy, now I have a better idea of what sizes, brands, and practices to focus on for my assessment of what to get next and how to use. Thank you.
James, another AWESOME video! Thanks! A tip I learned about Forstner bits that you didn't mention is starting the hole with the Forstner bit in REVERSE. If you start in reverse you don't get the tearout that the sawtooth Forstner bits can create. Start it in reverse, cut through those initial fibers, then drop it into forward mode and finish the hole. Saves having to use a scrap piece...
Your content is awesome and appreciated, another happy subscriber!
Thanks for the tips. Love your channel.
Thanks for sharing those tips!
Those tape tips are solid gold!
Many useful tips, explained clearly and concisely, although sometimes quietly. Thanks much, James.
Thanks James, printed out the drill speed chart. Lots of great information as always. Fred 🙏🏻🙏🏻👍🏻👍🏻👏🏻👏🏻✋🏻✋🏻
Every video you make I learn something new and find out I’ve been doing something properly.
Thank you James, sound advice as always and it was a revelation when I bought a set of Fisch bits. So much better than my DIY set 🌞
Dude these tips are GOLD!!! thanks!!!
I love your informative videos I use everything I've learnt in last few years of watching your videos keep them coming
Excellent video! Very helpful tips!
Thank you very much for this useful information 👍🏼
Using the scrap piece as a guide is brilliant. I will defiantly use that
Great content. This answered several questions I had, as well as a few I didn't know I should have.
Fantastic tips.
another very useful video, thanks so much
excellent tips! thank you
Great tips! Thanks👍👍
Another great video! When I use forstner bits, torque vs heat is a recurring issue for me, so thanks to your advice I'm now also a fan of the WAVY forstner bits. 😍
Very informative video SN! Never knew about those wave rim forstner bits before now. Thanks! 👍👍
GREAT video, and idea.
I always learn something when I watch your videos!
Wow, great tips!
Excellent! Wish I had known some of these tips months ago. Will definitely keep them in mind for future use, though. Thanks!
Excellent video, thank you for some very good tips.
Excellent young man, very knowledgeable.
Great information that makes sense.
Hadn’t seen this one even though I subscribe. You always provide at least a tip or two I haven’t heard before. Thanks!
Always good info much appreciated
I appreciate the sharing of your knowledge and experience along with the physics of getting things done. This provides me with a logical way to remember the tips and tricks you share so I can get it right all the time.
Thanks Stumpy, very informative, some really useful tips there,
I always come to this channel for the LD on things. Reliable source.