How To Build Motorized Bicycle Part 7 - Install Clutch Cable & Lever
ฝัง
- เผยแพร่เมื่อ 24 ส.ค. 2024
- How To Build Motorized Bicycle Part 7 - Install Clutch Cable & Lever
Check out my Website for more information on my creations:
hughesmotorized...
Tools & Equipment I Use in Fabricating Motorized Toys:
Sheet Metal Elactric Cutter Tool: amzn.to/2lf1Y3Y
Sheet Metal Plate Shear: amzn.to/2lb1jQT
Sheet Metal Brake: amzn.to/2lqcIMZ
Metal Cutting Saw: amzn.to/2jUVh6M
Plasma Cutter: amzn.to/2leyTFN
English Wheel: amzn.to/2latNu2
Budget English Wheel: amzn.to/2SyNVTg
Oxy-Acetylene Torch Kit: amzn.to/2K0k9TM
MIG Welder: amzn.to/2l6m6Fk
TIG Welder: amzn.to/2lezYxl
Epoxy Gas Tank Sealer: amzn.to/2lf3xim
Chain Cutter Tool for Drive Chain: amzn.to/2jMQlkd
Pedal Chain Breaker: amzn.to/2lf4dUW
Angle Grinder: amzn.to/2leAQ55
Cutting Discs: amzn.to/2jKw26Y
Flap Grinding/ Polishing Discs: amzn.to/2jNA2no
Laser Line Tool: amzn.to/2SFu2tR
I rode my motorized bike to day for the first time today, it fired right up and held together nicely. I got 300$ into the build and it was worth every penny.
This is awesome. The guy that sells bikes here in Tucson doesn't seem to care about servicing them at all. This and a $5 cable from Amazon just saved me a ton of time. Thank you!
Ive made it to video 7.
So far, your video has been a life saver due to the instructions that came with my bike have been vague to say the least.
Same here
Mine said build bike and ride😅
ZTmoto phantom 85 doesn’t come with any
wonderful video. I had to suffer thru at least 12 how to videos that was total crap. Then i found this wonderful very clear easy to follow video. Good job man and Thank you.
I am thankful for this video because the instructions that came in my kit said “install the clutch” without any further instruction or pictures to help
This is helping me right now on a motorized bike I found thown away missing some parts. Will be sitting up the new throttle and cable, along with the clutch and clutch cable in the next few days. Have to learn to how and when to adjust the idle higher or lower. Great videos
About the clutch arm an the screw not being in it was what I was looking for .. an I got so lucky cause this was the first video I clicked on. Thank you so much.
II cleaned pads for clutch and put new clutch lines . How do you make sure the clutch will engage?
So thankful for these videos
Good job this really helped me out with my wife's bike! Your Utah friend. My wife loves her bike!
She loves the doggy style too
Thank You!!!! The instruction I got with my kit was so bad I could not even find the tank , never mind the clutch Life Saver!!!!!
Very informative video. I am having to replace my locking handle now. Thank you.
More than GREAT...Thank you for your great effort and clarification
👍👍👍👍👍👍👍👍👍👍
THANK YOU BRO. ... I HAD SOME TROUBLE WITH MY INSTALATION OF MY (66/80cc Flying Horse Silver Angle Fire Bicycle Engine Kit - 2 Stroke). I USED COMAN SENSE ON MOST OF THE INSTALATION . UNFORTUNATELY THE VIDEO INSTUCTIONS (ON A BURNT DISK) WOULD NOT PLAY ON MY BLUERAY PLAYER. AFTER WATCHING VIDEO AFTER VIDEO , I CAME ACROSS YOUR WELL INFORMED , STEP BY STEP VIDEOS. WHICH GOT DOWN TO THE POINT WITHOUT ANY EXTRA, USELESS , UNWANTED. BABBLE, COMMENTARY. GOOD JOB SIR. YOU GOT DOWN TO THE POINT AND IT WAS REALLY , REALLY USEFULL INFORMATION. 👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍
Thank you so much had trouble figuring out the clutch springs.
Glad I could help
Mine still doesn’t engaged is it the flower nut?
Hey man I just got a two stroke the lever is completely loose moving then just stops I don't feel any engaging? I haven't got it all together yet so I'm curious if it's hood
nice work on the video.
great video thank you I have a huffy panama jack iwant to do this to I just hope I can do it as well as you
It's obvious the comments have no experience with building and what this guy does is fine for a video but not for reality.
Instructions unclear person was choked
Can you tell me if a stock tag joint will fit on a 20 inch schwinn stingray rim
You're about as shaky as I am lmao
The clutch is so incredibly stiff that it takes two hands squeezing as hard as possible to engage it. There is no way my son will be able to operate the clutch. Any way around this?
Did you tyrwap the cable to the frame w/ some tight bends? That would make it hard to operate
@@HughesMotorized I avoided tight bends, and it was stiff before I tie wrapped the cable. I even find it very difficult to push the throttle handle itself. It hurts with a bare hand, seems incredibly stiff. I was almost thinking of extending the throttle handle a few inched to give more leverage.
I didn't have my cable set up rite is. All n r these things able to b ridden on the street without a
license
I am building one of these kits right now and my clutch lever (and the column that goes down into the area next to the flywheel) fell out and now I cannot get it to fit back together with the flywheel. Any ideas?
What if the arm only moves outward not inwards like yours did how do you fix that problem
Hello I'm trying to figure out this hydrolic clutch line and lever system cannot get clutch to engage or disengage help
Pull the cover of the engine and see if the mechanism is actuating when you pull in on the lever. I've never seen a kit with a hydraulic clutch however I've worked on them on cars . Same thing. You actuate the clutch and a piston pushes on the clutch shaft
@@HughesMotorized hello and thank you for responding yes the concept is basic and I've never seen one either so I'm going to tighten my flower nut tight and see if this will help and make sure my clutch lever tube is primed it's seriously crazy and only one vedio have I found ill keep you posted and again thank you
Peace
Bradford
Hi question have you tryed useing the clutch with a grip twist instead of a bike lever wuld it work
No it wouldn't
I followed all the videos-they were great. Bike is all together but the wheel doesn't turn now.
Sergey Miller Probably the bearing too tight in rear wheel or you didnt cut down dust cap on rear bearing
When you replace a clutch handle, do you have to take it all apart or can u just slide cable out of old one onto a new handle?
+Shawn Socha YES.. just remove from lever
Nice video. I did everthing that you did. But my back tire is stuck. Will not turn i wunder why??? Can u help me please... :)
Im guessing you need to look at the dust cap under the sprocket. if you did not gring cap smaller or drill sprocket hole bigger , it will bing rear hub
use compressed air to remove grips .
Just pry the edges up and squirt some DW40 in there.
I'd have 400 grips laying around in my shop. They don't sell for shit on ebay so not worth the time. Cut & toss in trash. A waste, but of no value
It's the better meathod, I dont have an air compressor so I just used lubricating oil and twisted it off
Throw some gas in there and light it up shoots off like a rocket
Is the hairspray industry standard?
Since I'm a bald dude my experience is deeply limited. However Id say all of the non-aerosol, pump hairsprays should work on fitting on a grip
What should I do if the clutch arm itself it way too stiff and stays in position ? I don't even how the wire in the arm yet because there's no way it will give enough force to move the arm. The clutch itself is also not stuck and probably too loose at this point, but the arm is stiff.
Also, I can move the clutch arm with my hand it just takes force
How much should the clutch arm move to engage ( 1/2 inch ..3/4?)
1/2 - 3/4"
teying to understand why the clutch wont engage
where do i get a replacement chain?
hughesmotorized.com/upgraded-chain-for-motorized-bicycles/
I fixed my clutch but the buke still moves without it
Check out my vid on 2 stroke clutch troubleshooting
The product links on your website don't work.
My clutch has a lot of resistance plz help. I can't get it to move.
The clutches are often stuck when new. I'll pull in clutch to disengage and push bike forward dragging the wheel and sit down hard on seat. This usually breaks the clutch pads loose and the clutch works fine.
HoustonMotorized I think its a problem with the cover cause when the clutch arm turns the cover want to pull off like There's not enough space
if the cover is moving the screws are loose, however since I cannot see what you are seeing. If you desire help, shoot a vid up close and well lit and email it to me @ houstonmotorizedbicycles at gmail . perhaps I can offer some ideas
HoustonMotorized thank you so much I really apreciate it. I got the clutch to work and its finally ready to go. You got a sub.
the a piece called a centrifugal clutch you can order what does it do and can it help there a guy you tube has one
What do you do if the arm moves outwards not inward mine only moves outwards not inward so what do i do in that case
Remove cover and find out why. Bucking bar improperly positioned?
my cable is frayed at the end and i can't get it through. Should i get a new one?
If you can cut or twist the wire back to original shape. You will be good
Does anybody know what this pin is for??
Yes, it's a bucking bar. It moves the clutch pads
Hey man, I need help, I'm doing this with my dad for the first time and I ordered it from some Chinese company with horrible instructions, we managed to get all the way to clutch assembly, but regardless of whether the clutch is depressed or not, when we pedal we hear the piston moving up and down inside...this doesn't seem right. Any idea what the problem is?Ps. Even when we manually push the clutch arm in, it makes no observable difference.We would really appreciate help, we're on a time crunch, before I leave for college.Thanks again.
+Silas Newsome Check for video on clutch adjustment by Bikeberry on YTube
HoustonMotorized can you leave a link to that video?
My clutch doesn’t work
want to know why my motorized bicycle it starts but it doesn't want to stay running?
Tovias Pauilno check the idle
My engine turns over even when the clutch is disengaged and you can't peddle it
The Clutch is stuck. Very common on these motors. You can try rmoving the sprocket cover and striking the pin that disengages the clutch with a hammer. be careful you do not lose the pin that goes into the shaft. If that does not work, you will need to remove the clutch cover and tap on the clutch assembly cover inside. don't hit it too hard so you dent the cover but give it some good hits. If that does not work you will need to loosen the screw inside and adjust the clutch. there are videos on how to do that
great job. where u from?
Im a Texas boy. I learnt my eanglish in Texas skools
hey again now I'm having problems not getting a spark
+Darrell Smith Most likely you need magneto coil
how to buy gas kit
The law say: don’t go over 50cc don’t go over 30mph. Why is this cop bothering ?
*cuts himself and nearly bleeds out*
I have paper thin skin. I just barely bump my arms or backof hands and I'm toer open.
He skipped over the most important part. How did he install that beer holder?
cant figure out that, send me your beer
Omg have no idea what i need to drill. Im so bad with engines.. .
You drill the handlebars. I point it out on the video
Nice job! Where did you get your bike?
Walmart
Can you ride these in the street legally
You can if it's a 49 48cc
depends on your state, check local/state ordinances
That's not rite,,u push clutch arm in far as it go then tightn
Lol I hope your kidding
This dude is OG status......... all the while with a cigarette in his mouth and bloody knuckle.
Some people are always complaining about something. The guy is just helping us out. God knows that I needed his help.