Great videos I have ever seen I have one question my water pump pully is wobbly but I have no issue with cooling system like car is not heating up and no coolant leakage Do I stilll need to change whole water pump or just pully is enough please guide me. Thanks.
Hello. Thank you. Please. Change the water pump. Sooners you can. You will overheat the cylinder heads. Trust. It happened to a customer that i told To replace. When i did the diagnostic. And he wait for a week to do it. And. He overheated the engine. Cost was around 4500. If you have any questions. About anything that use fuel let me know. 😊
@@1Wayfix thank you again that was my first comment ever on TH-cam channels I am subscribing your channel and share I have 2008 Kluger front wheels drive
Hi 1Wayfix, This is a great video with several details not found in the one by Car Care Nut who is very highly regarded in the DIY community. I would appreciate it very much if you would address a few of my questions. At 5:10, is it OK not to remove the three 17 mm nuts after removing the 19 mm? At 7:54, what are the lengths of extension rods (I saw two long ones connected)? Is it possible to get the entire job done without crawling under the car? Thank you.
@@1Wayfix Thank you very much for the prompt replies! I think your video may have more viewers if you add words Toyota 2GR-FE Engine, 2010-2015 Lexus RX350, 2011-2016 Toyota Sienna, or Camry V6/Avalon V6 in the title, because all these cars used the same engine. Have a blessed day!
Great videos I have ever seen
I have one question my water pump pully is wobbly but I have no issue with cooling system like car is not heating up and no coolant leakage
Do I stilll need to change whole water pump or just pully is enough please guide me. Thanks.
Hello. Thank you. Please. Change the water pump. Sooners you can. You will overheat the cylinder heads. Trust. It happened to a customer that i told To replace. When i did the diagnostic. And he wait for a week to do it. And. He overheated the engine. Cost was around 4500. If you have any questions. About anything that use fuel let me know. 😊
@@1Wayfix thank you again that was my first comment ever on TH-cam channels
I am subscribing your channel and share
I have 2008 Kluger front wheels drive
I am located in Australia
@@baberali407 thank u.
@@baberali407 wow. Any question leave here. I will do my best to help 😀
Thanks for video. Is that silicone on the screws or is it anti-seize?
Thanks for thumbs up. I would like to know what kind of silicone to buy or if that was anti-seize. Thanks
Gracias amigo! 💯
@@pablolugo9824 😃😃
@@pablolugo9824 De nada. Cuando nesesite. Ayuda. Solo comente por aca 🙏😃😃😃
great job!
Thank you so much. For you comment. Any question leave here I will do my best to help you 😃😃
Hi 1Wayfix,
This is a great video with several details not found in the one by Car Care Nut who is very highly regarded in the DIY community. I would appreciate it very much if you would address a few of my questions.
At 5:10, is it OK not to remove the three 17 mm nuts after removing the 19 mm?
At 7:54, what are the lengths of extension rods (I saw two long ones connected)?
Is it possible to get the entire job done without crawling under the car?
Thank you.
For the first question. Yes It’s better to remove the 3 17s. Bolts. Because. You have no room to lift the engine. Enough
For de 2nd question. They are 12 inch. Each. Extencion
Fort the 3d question. You dont have to crow. Under. You can do it from the side. But. You will need to lift it. To. Remove the wheel.
@@1Wayfix Thank you very much for the prompt replies!
I think your video may have more viewers if you add words
Toyota 2GR-FE Engine, 2010-2015 Lexus RX350, 2011-2016 Toyota Sienna, or Camry V6/Avalon V6
in the title, because all these cars used the same engine.
Have a blessed day!
@@peterking8722 i will add. That. Thank u. 🙏
It goes silly cone Ahn Dee back