Thank you buddy.. I put together a 16S lifepo4 pack And I'm ready to install my JK BMS with Bluetooth and active balancing.. Your instructions will give me the confidence and enable me to do this easily..
Thanks for the instruction. Be careful when tightening the bolts with a wrench - don't drop it to the contacts! Where to exactly plug in the switch for the BMS?
Nice video....Can the JK BMS cables have more than 0.08 R?...I changed all the wiring of the connectors for a #18 cable and the resistance went up to .162R....Will that affect the balance of the cells in any way?...Thanks
Thanks so much for the video. I have the exact same setup for my home running a 6000W inverter, 3500W of solar panels and a mid nite classic 150 charger. I was wondering if you could show us all of your settings on the app so I can compare. Thanks in advance!
LiFePO4 comes under hazardous cargo. Air cargo is not accepted. Only sea fright accepted. That too, only few limited special carriers will accept these cells. Be careful to select the correct shipper before purchase
@@HappyGreenerWorld I'm sorry. I meant how did you clear these from customs?. did you personally go to customs or through agent ? A few months ago, I bought rack mount batteries from a seller who used a forwarder for shipping. However, for my next purchase, I want to use direct seller shipping instead. I'm unsure about the clearance process involved in this method.
@@bonnetalexandre2085 There is no such requirement ! You just set float/bulk charge voltage and low/high voltage cut off in inverter . Rest of the controls are by BMS. Any way there is a voltage difference at battery terminals vs inverter in due to terminal resistance when drawing high current
As I have demonstrated on latter part of video , BMS will cut off charging once, at least one cell raches maximum voltage threshold . TF no need to warry on overnight charging and battery protection .
Positive terminal of 9th cell is connected to negative terminal of 10th cell by busbar . So, you may connect BMS wire to either of these terminals. Both are correct
Best most comprehensive Video on installing a JK BMS. Very well done 👍🏽
Thank you buddy..
I put together a 16S lifepo4 pack And I'm ready to install my JK BMS with Bluetooth and active balancing..
Your instructions will give me the confidence and enable me to do this easily..
Thanks for the instruction. Be careful when tightening the bolts with a wrench - don't drop it to the contacts! Where to exactly plug in the switch for the BMS?
හොඳ පැහැදිලි කිරීමක්. ස්තූතියි ඔබට
Thanks for explaining this in great detail :) Greeting from the Netherlands :)
Nice video....Can the JK BMS cables have more than 0.08 R?...I changed all the wiring of the connectors for a #18 cable and the resistance went up to .162R....Will that affect the balance of the cells in any way?...Thanks
Thanks very much. Very helpful
Fantastic Video! Thank you, Sir!
Thanks so much for the video. I have the exact same setup for my home running a 6000W inverter, 3500W of solar panels and a mid nite classic 150 charger. I was wondering if you could show us all of your settings on the app so I can compare. Thanks in advance!
Glad it helped
Dokładnie o o mi chodziło, Poland pozdrawia.
Question 🙋🏻 P- is for Power minus out and also for charge minus in ?!
Why do you have a negative cable coming off the battery bypassing the BMS?
Why starting no. 9 string to no.15 string you connected to negative side of the cell? i thought all in the positive side
What guage is the bms main in and out -
BMS is amazing tech. wish this can be done with Tall Tubular Battery, lead acid ones
Leadasid battery does not need BMS
Is there any signal wire from BMS to increase the signal of Bluetooth
Thankyou só much!❤😂🎉
Thank you for the video!
Glad it was helpful!
Where can i get this battery. Pls send the link to purchase this battery.
Hello sir. Could you please give instructions on how calibrate Ah too?
What about the P Wires?
Please guide me how to pair BMS with my car Android screen also.
I am trying to pair my battery with smart phone. It messages make. And I am in doubt it is due to weak signal from bms.
nice video. I have a question regarding shipping method of these cells. Was the shipping method door to door or CIF and we need clear from port ?
LiFePO4 comes under hazardous cargo. Air cargo is not accepted. Only sea fright accepted. That too, only few limited special carriers will accept these cells. Be careful to select the correct shipper before purchase
@@HappyGreenerWorld I'm sorry. I meant how did you clear these from customs?. did you personally go to customs or through agent ?
A few months ago, I bought rack mount batteries from a seller who used a forwarder for shipping. However, for my next purchase, I want to use direct seller shipping instead. I'm unsure about the clearance process involved in this method.
@@semirauthsala6001 Through a forwarding company who accept Li batteries
Sir can you please provide the link where from boy jk bms
Aliexpress
Are you not gonna connect those 2 big Black wires of the BMS with the battery terminal?
No. They are connected to inverter or charging souce .
BMS is in series with charging source .
Hello thank you for your video!
Does it need a cable to communicate with the hybrid inverter ?
alex.
BMS does not communicate with Inverter in my case
@@HappyGreenerWorld why?
@@bonnetalexandre2085 There is no such requirement ! You just set float/bulk charge voltage and low/high voltage cut off in inverter . Rest of the controls are by BMS.
Any way there is a voltage difference at battery terminals vs inverter in due to terminal resistance when drawing high current
@@HappyGreenerWorld ok thank you !
Mistake starts from no.9 u should go for positive terminal
Connection Diagram please
Does this BMS balance the batteries well? How long have you been using it? Are there any problems with this BMS?
I have been using JK BMS for more than an year now. They perfectly balances all the cells below 0.005V
Suppose I leave the batteries charging overnight will the batteries get damaged or the BMS will protect from overcharging?
As I have demonstrated on latter part of video , BMS will cut off charging once, at least one cell raches maximum voltage threshold . TF no need to warry on overnight charging and battery protection .
Hi. Why didn't you connect bms wire to positive of the 9th cell?
Positive terminal of 9th cell is connected to negative terminal of 10th cell by busbar . So, you may connect BMS wire to either of these terminals. Both are correct
@@HappyGreenerWorld OK. Thank you.
Why starting to no. 9 to no. 15 string are connected in negative? Suppose to be in the postive side?
👍👍
Good job
Which company cells are these? How many charge cycle in its lifetime ? Also what is the price of each cell? Pls reply all my queries
Manufacture CALB . Retail by Shenzhen BASEN Technology at Alibaba.com . 3000 cycles . $82 per cell
I am using 2 volt 24 s 72 volt battery
Hi sir
Please respond
Hi
Hello sir sir
I am purchasing is cells
I am from AP Andhra Pradesh Lithium phosphate cells cost
@@rameshelectricallab9556 you can check from Alibaba.com
P-