ฝัง
- เผยแพร่เมื่อ 12 ก.ย. 2024
- Hello,
This video shows how to replace the power window lift motor on 1980-1996 Ford Broncos and F-Series trucks.
The video shows the simple method that requires to drill out the dimples Ford made to access the window motor bolts, no removing the regulator required.
1980-1991 only requires removal of the top door panel (its a 2 piece door panel as shown in the video)
1992-1996 the whole door panel removes as one piece
Tools Required:
-Phillips screwdriver
-Flathead screwdriver
-5/16 Wrench and socket (for motor bolts)
-1/2 Drill bit with Drill
-Replacement motor (make sure to buy for the correct side L/R)
-Replacement door panel clips
Replacement Parts:
Power window lift motor:
amzn.to/3xyTmoj
Window motor Gear:
amzn.to/3AqkIyM
Drill Kit:
amzn.to/37pVkg9
Please remember to like and Subscribe, Thank you for watching!
***Disclaimer: This video is not sponsored. I use affiliate links. As a customer, you do not pay any more or less because of an affiliated link. A small percentage of the sale will go to the person who generated the link. Thank you for supporting my channel and helping me grow.
![โฮ่ง! (SUGOI) - LYKN [ OFFICIAL MV ]](http://i.ytimg.com/vi/nFp4zjAARFs/mqdefault.jpg)
I’m literally restoring the exact same bronco. This is great!
Sweet, these are great trucks.
This video just saved my life! I’ve rebuilt the drivers side motor already and the rivets were replaced with bolts. When I popped the passenger side off the rivets were still in it. Thanks for the videos, they have been really helpful with my 91 Bronco!
Thank you so much for sharing! Love your bronco videos👋🏻
Thank you so much for the video, just replaced the motor on my 1992 ford bronco. 🙌🏼💪🏽🙏
Glad it helped
Man you made that look easy thanks
The hardest part is removing the fragile door panel. Be careful and avoid damaging the clip locations as these parts are getting harder to find.
Glad I found this video. I much easier than replacing the regulator and all.
This is the fastest way to replace the power window motor on the 1980-1996 ford fseries and broncos. Let me know if you need any help regarding this repair.
Great job!!🙌🏻
Man I cannot get the gears lined up at all
Do you have any tips to how you did it??
@@isiahcalhoun2218 make sure the gear looks the same as the old one. If so then apply power to the motor (plug in the motor and hit the window switch in either direction) and move it a little.
Thanks for the video
I will try it
Your welcome
Great video thanks 👍🏼
Great video thank you for making
I have a 1992 in pretty good condition, 70k, but the same thing happened with auto window. Where do you recommend getting replacement motor? I think mine is a gear also, as it runs and I need to pull it up to close. Is it easy to replace the gears? Thanks in advance
If your motor is original then you can rebuild the gear, there are plastic plugs inside the motor that strip. The plugs are sold online, otherwise the Dorman motors I linked in the description work good.
Thank you sir, it is a original and I will give it a shot@@TheFixTech
Great video, saved me a lot of time blood and sweat
Nice video, thx
I showed you the right path and you wondered
....but it’s been proven, the earth isn’t flat
I used epoxy to fix a few broken clip tabs on my 89 door panel. Worked great, can't remember what the bit size was for the center, but that plus a little dremmel action and it's good as new. I'm sure you could do the same if you have issues finding a tan replacement panel at local yards.
Thanks I did as well but since most my tabs were broken and the epoxy is permanent the clips would not move around to fit into the door properly. It worked but the panel was not lined up properly, ended up finding a nice used panel.
Thank you for making this video. You did not repair or replace that ripped plastic sheet before you re- assembled the door panel. Can you please explain why or why not that is important?
It is important for road noise, I did replace that sheet eventually with sound deadening material in my clean and deaden video.
Make a video on how to do the rear window motor just subscribe thanks
For the rear window I usually rebuild the original motor. Some people use small metal ball bearings or nuts, using metal parts will damage the motor. Replacement plastic glass “plugs” are available and are preferred, that is what I use. I will try to make a video soon.
Thank you! This was really helpful, as I need to remove this panel for repairs in my '93 XLT. Regarding that plastic weather liner...did you replace that as well?
The belt weatherstrip on top of the panel? Yes I did I replaced both the inner and outer and purchased from rock auto.
@@TheFixTech Thanks so much!
how do you remove the bottom piece?
The bottom piece of the door panel? that piece is screwed on with several screws.
I can't believe you did that to your door. That bronco is ruined.
You lie