Error code on KTM Duke 200 / low voltage problem "stator coil" check engine sign.
ฝัง
- เผยแพร่เมื่อ 5 ต.ค. 2024
- Malfunction blink codes on KTM Duke & RC, through check engine sign;
1. (2) short blinks = Crank position angle sensor malfunction
2. (6) short blinks = Throttle plate / position angle sensor malfunction
3. (9) short blinks = Manifold absolute pressure sensor malfunction
4. (11) blinks = 1 long + 1 short = Idle Air control sensor malfunction
5. (12) blinks = 1 long + 2 short = Coolant sensor malfunction
6. (13) blinks = 1 long + 3 short = Air intake sensor malfunction
7. (14) blinks = 1 long + 4 short = Fuel tank sensor malfunction
8. (15) blinks = 1 long + 5 short = Rollover sensor - circuit fault
9. (16) blinks = 1 long + 6 short = Radiator fan motor malfunction
10. (17) blinks = 1 long + 7 short = Lamda/ o2 sensor malfunction
11. (18) blinks = 1 long + 8 short = Engine diagnosis warning lamp malfunction
12. (19) blinks = 1 long + 9 short = Fuel level warning lamp
13. (21) blinks = 2 long + 1 short = Engine control relay malfunction
14. (22) blinks = 2 long + 2 short = Engine speed signal malfunction
15. (23) blinks = 2 long + 3 short = Travel speed sensor malfunction
16. (24) blinks = 2 long + 4 short = System voltage Low/High
17. (25) blinks = 2 long + 5 short = Side stand switch Malfunction
18. (33) blinks = 3 long + 3 short = Fuel injector failure
19. (41) blinks = 4 long + 1 short = Fuel pump relay failure
20. (45) blinks = 4 long + 5 short = Lamda/o2 sensor Heater failure
21. (49) blinks = 4 long + 9 short = Idle control malfunction
![The Wall Song ร้องข้ามกำแพง | EP.213 | กรีน อัษฎาพร | 3 ต.ค. 67 [1/5]](http://i.ytimg.com/vi/3KrlLbCsadI/mqdefault.jpg)
Damn, this is the most helpful video + description for ktm users in youtube😂 really thanks
Qué tal amigo saludos desde México muy bueno tu video explicativo y con tu base de datos en el los errores de código saludos ya estamos suscritos a tu canal
english pls. thanks
th-cam.com/video/ui4Lf8HccgE/w-d-xo.html
Thanks big full help ❤❤❤❤❤
Hi bro, do you know what about blink code 7 long 8 short in a Superduke 1290r 2014?
Nicely done! My 2012 Duke 200 also shows me flash code 24 intermittently and at the same time causes the idle rpm to either rise to 3k continuous or fluctuate between 1100 and 3000 rpm quickly. Occasionally it so happens that opening the throttle fully doesn't rev the engine but just makes it fluctuate between 1100 and 3000 rpm. What could it be? The flash code and idle issues occur at the same time.
FodderRev sorry for the late reply. no Internet. do u see any on the description i typed?
FodderRev just check ur stator coil. better let someone to do it or if u know how u may. if stator is burned, then change a new one. thanks sir.
@@reverendcoward7941 Thanks for your response. The stator output is fine. I had been taking my bike to the workshop often and they explained all the symptoms over the phone to a member of the KTM R&D team. He almost immediately responded by saying that the wiring harness needs to be changed. There are a lot of broken wires in it that have been rejoined at several points mostly near the steering head bearing. Need to wait for the part since it needs to be ordered.
i see. i encountered a customer too having a problem on its wire harness near the steering bearing part. everytime u full lock its rotation to the left and right the power goes off. i found out some wires worn-out already. by the way, hoping ur bike could be better than ever now.
@@reverendcoward7941 Yes, I have had that problem too. A total of 6 or 7 wires have been repaired already. As for the wiring harness replacement, it will take 15 days for the part to arrive. Long wait.
I'm getting jy_1.4.2 error in speedometer while trying to start my rc 200..and the bike is not starting...I don't know if it is a problem related to low battery or the coil that recharges battery while bike is running?
Ey bro sup. Been suffering with that issue? Ahm, before anything else, i go advice to check ur battery terminals, clean it if possible and tighten it. And the connections especially the rectifier and stator coil and all those neccessary for charging components. If still the same, check how many years is your battery and test your rectifier and lastly, the stator coil if it's burned or not.
@@reverendcoward7941 thanks brother 👍🏼
Anytime bro. Just update me.
@@reverendcoward7941 ey bro. No problem with stator or wiring.. problem is with the battery 👍🏼
@@kohilskottarathil3936 that's good to know then. That's always the best thing to do next time around, check the things that are related to the issue. Must not execute to major thing to do when it's not necessary. Have safe trip always bro.
Hi Bro, i have problem with the battery. I've check the battery.
When position off, it is measure 12,65 VDC and then when i start to cranking motor, the voltage is increase to 13,75 - 14 VDC.
But when i turn off the motor, and then i try to turn on again, there is still any message "Low Battery" in LCD.
What should i do, charge the battery or replace the battery with new one?
Please answer.. thank you so much.
Hello sir. May i know if how many years already is your battery? And if it's still 1 or 2 yrs, try to tighten the battery terminal and also clean it by sanding. If same issue occurs, please recharge your battery then install it back. Please update me. Thanks.
Bro my ktm duke 125 c bike is biggest problem facing 30days engine check light always blink 4 nd 6 times blink than I buy obd2 meter thank check show the problems tps sensor code error and engine collant heat temperature sensor problem but im living to Bangladesh so ktm service centre don't have my nearest area . Bro plz helping me how too solve this problem 😭😭
Hello bro good evening. I hope ur giving me the correct error. If dealer is really far from ur place, try to check ur fan if it is working. Let engine on wait for the fan to turn on. If not, turn it off. Check also coolant level. Check also fuse box. There is so much thing to check bro. I hope if u will have time, bring it to ur nearest dealer to fix the issue.
Hey Mate.. Greetings from India 🇮🇳
Please help me sort this issue with my duke 200 Bs3..
Without giving throttle(acceration) the RPM get's raised to 3000 and the warning light blinks continuosly... this issue comes and goes while riding only..
I have got the ECU checked, accelerator wire replaced but the problem is not resolved yet.. I hope u have the answer..
Is the bike still under warranty?
bro I use full throttles by listening engine sound wroomm....... wrommmmm ....wroommmmm....does it effet bike ? my bike is duke 125
Normal sound will be that if u full throttle, not unless u will another sound that u might have heared b4.
@@reverendcoward7941 does it effect engine
Ahh i see. Yes bro once the bike just started. Let the bike warm up 1st like for about 2 to 3 minutes . U can full rev after but please not all the time. Hehe
Pro i have problem same in my ktm smc 690 i change voltage Regulator Rectifier and buttry but same problem do you think it will be stator? And how i make inspiction for stator can u suppurt me
Sir, if u have ktm company nearby ur place. U may go there and have it use with diagnostic test since it's 690cc.
My duke 200 bs4 model recently cranks but is not starting up, i can here the starter sound but no ignition all lights horn working perfectly, what might be the issue
Did u do anything to ur bike so far before the incident happened?
Nothing else bro, just had done my 30k service in dec and changed my front brake pads in jan, all from ktm authorised service centre,
@@mohammedirfan4009 did u fix it? A little late but having the same...
My bike is not maintaining idle speed and,its rpm is fluctuating, moreover it seems like there doesn't occur regular spark in the cylinder, i checkd the spark plugs and keep doing it since 5 days, engine is also overheating, black smoke sometimes come out while cranking, above 5-6k rpm the engine is ok but below, there is problem, my engine is ktm duke 390
I too have same problem bro as urs..i cleaned the throttle body air filter,fuel injector.changed saprk plug.but still it gets turned off when i dont accelerate.
@@SuperBulletforme notice the sequence of check engine light, i have 1 long blink and 3 short blink, and 9 long blink. Issue is still on the engine, the mechanic said throttle body and fuel pump had to be changed
My problem is that it starts normally but when i try to ride it just starts to stall. Idk what to do. It blinks one long and one short. And i dont know if its about the battery. Maybe the fuel injection. Its s 2015 so its a carburator injection.
I suggest to check your stand sensor if it's working fine. If working fine, next step, clean your throttle body and its components with carb cleaner or can be regular gasoline. Also double check the connector of your idle air control sensor. If not familiar, please bring it to the near ktm dealer or expert mechanic of ktm.
bro my bike is duke 125 bs4 i can't change the time im tried lot of times but no use please help me
Press the MODE button to go through ODO mode.
Hold and press the MODE & SET button together until the time flashes then set the desired time. To make it more easy, refer to your manual. Drive safe.
@@reverendcoward7941 thank you for reply
i know bro im set the correct time but changed to wrongly automatically
im tried lot of times please help me to fix the problem
@@dukeparthi just to the same process bro to set the time again.
@@reverendcoward7941 im tried lot of time not work
@@dukeparthi please refer to the manual you have and you might let someone to do it.
Brother I need help with my duke 200. Flash code blinks 2 short 2 long. Bike runs ok. Flash code only appears when stationary but goes off while riding. What could be the issue here. Please help thank you in advance 👍🏻
As what I have provided on the description. It's signal speed malfunction bro.
@@reverendcoward7941 yea but I don’t really understand that. How can I rectify the problem? What should I check or change? Thanks brother 🙏🏻
If you have not enough knowledge about it it's better to bring it to the nearest dealership to serve your concern maybe a motorcycle shop that can actually fix the issue . Much better too if they have a diagnostic tool.
I'm facing issue in ktm rc 200, engine check light is steady on, what could be the issue, it's not blinking but steady on
May I know bro if anything is wrong happening to ur bike right now?
If none, try to remove the battery whole night then put it back in the next day. Be careful in putting back the terminals. Correct placement of pos and neg should be observed.
What the meaning of engine light keep on pop up and there is no blinking..ktm duke 200 2013
Bring it to the nearest ktm dealer and have it deleted by their diagnostic tool. Or remove the battery the whole night then install it the next day.
Bro my ktm rc 200 2 slow blink and 5 fast blink whats the problem bro can you tell me
Check the description sir. Thanks. Have a good one.
Bro i have same problem, I want call u
but what is the reason the fuse popped? did you find it?
or is it the fuse alone, which has defect or something like that, that's why it popped?
edward newgate it's the stator coil has problem. fuse were cut since triggered by main issue.
@@reverendcoward7941 so you bought new stator after replacing the busted fuse? did you use again your bike after just replacing the busted fuse? did it popped again? or it didnt until u replaced the stator coil with new one?
fuse no longer popped up after i change new stator coil bro. sorry for the late reply. don't have load most of the time.
hello friend I would like to know why it does not blink and the light remains static thanks
You mean the check engine is steady sir?
Bro meri baik duke200 he usme problum aa raha h
Pickup nahi le rahi he or 60 ki speed ke uper nahi ja rahi h
Or abhi 4 5 din ke bad battry bhi charge nahi ho rahi h
To muze lag raha ye problum magnetic stator coil ki ho sakti h apko is bareme pata h Ripley krna bro
Check fuel pump once...
1 long and 1 short ktm Duke 200 whats the problem? Thanks
It's on the description sir. Idle air control malfunction. Thanks for watching.
Please don't add background music ..
Its so irradiation
same problm with ktm rc125 just 5mnths old...wat to do bro ani solution yar .? im rele worried..
If bike is still under warranty. Please report it to you nearest dealership.
bhai kick bhi nhe hai dhaka mar2 ke start karata tha abhi toh dhaka se bhi start nhe ho rha hai bike start hi nhe ho rha hai kya batry problem hosakta hai??
I've duke 200 Bs6 Model... I've purchased it 1 weak ago... I've been coming a issue in my Bike that Engine Light is always on when i drive .... No Blink issue only Always on
If bike still under warranty. Bring it back to the dealer and let them erase the error on the panel. Sorry for the late reply.
It's ohk Broo !! Don't say sorry 😊 I'd gone the dealer (showroom) where i purchased the Bike He told me that If Engine temperature was too much low so this issue generate don't be panic that's not a big issue Bike is new then it's a common problem you ride some kilometer then it will be fine..
Now everything is okey
I have rc390 my engine light is not turning off while riding plzz help me with this
shaik Mustafa Hussain unplug battery, remove 1st the negative terminal. if and only if the check engine is steady on.
Rev. CowarD thankew for the quick reply brother I'll try it once
yes no worries.
Bro 1 long and 5 blinks in engine light what to do Bro plz say
it's a circuit fault bro. rollover sensor. pls do check. maybe it's just wet. try to dry it up. if it's broken, then need to buy new one. see the picture on Google if your not familiar with the Rollover sensor look like. thanks. sorry for the late reply. don't have loaded from past weeks.
Bro my Duke check light still indicating..how can I solve it.??
Can u tell me bro what error the blinks indicating?
Bro send Ur what's app num or Email I'd I'll send error image or video..
Hello bro if u have Facebook account ,much better. I don't have what's app. Search me on Facebook Reverend CowarD.
@@reverendcoward7941 bhai help carona
Bro my duke 200 when power button on that meter sound is not coming.. what was the problem?
Bro u mean the display panel is not showing anything?
friend my duke 390 shows 1x long and 8 short, what's the problem? what should I do? Thanks for the help.
Hey my friend it's engine diagnosis warning malfunction. Better to go to ur nearest dealership and let it check by using diagnostic gadget to correct the error.
Bro i have been change new coil magnet but still not charging
My bike warning light blinking 1 long and 5 or 6 short blink whats the problem please reply
Bro...same problem here... Did you find the reason why?
Same with me, what is the prob? Have u solve it?
Bro what's the reason for check engine symbol. It Binks 1long and 3 short. What's the issue can u let me knw. Coz I didn't understand in your caption.
That's the air intake sensor. Please get ur bike serviced from your dealer if still under warranty. But if no longer under warranty, try checking ur air intake sensor, clean it with contact cleaner. Or try turning off your bike, count for 2 seconds then turn it back on then do it again for 3 times. Last option, try to remove your battery for whole night then install it back the next day morning.
Bro 4long 5short plz help please
@@amihussain4407 hey bro that's the lambda sensor. It's failing. If bike is still under warranty, please bring it to the dealer and get it fixed. If not, you may remove the lambda sensor located on your headers pipe. I think that's a 17mm or 14mm open wrench . And also before removing it, make sure to unplug the socket. Clean it with contact cleaner. Try plug it back in. If still the same, remove battery for one night then put it the next day morning to reset ecu.
Made video for 2 short +5 long side stand malfunction plz sir plz plz
Hello sir. Soon if there will be customers that will have that kind of issue.
@@reverendcoward7941 OK sir
I am up with side stand problem. 🙋♂️ please help.
@@simondcruz2821 pls check near the side stand, there is a magnet. Double check if side stand is folded, magnet should be closer to a black square plate. Behind that square plate is the chips. Do use a paddock stand.
@@reverendcoward7941 and what about the engine yellow light.. its not blinking, its still & stagnant.. always on..
Its not blinking...its glowing fully
What may be the problem
Bike is running normal? If performing normal, just try to remove the batter for 12hrs then install it again.
@@reverendcoward7941 yes it's running normal,but if bike is untouched for one whole day,there is a struggle.when i got to start my bike the next day it's starting after two to three attempts clicking the ignition.
Help me bro, my rc390 having 1x long followed by 7x short blinks.. what is the problem?
It's the lambda sensor bro. Please do clean your lambda sensor and connector or before doing it. Please try to unplug batter for 12hrs then install it again. Be Careful. Thanks.
@@reverendcoward7941 bro.. now engine light stays on all the time.
My duke 390 is having a starting problem. I've just got the new battery but it's still showing low battery and cannot the start with electric starter. Please help
Hello my friend. Pls do check it to ur dealer if it's still in warranty. They can trace the problem using the diagnostic tool. Otherwise, u may check directly ur rectifier and stator coil. Also check the tightness of every terminals. Like the starter relay. Check also Sparkplug.
Check earth connection under fuel tank.
Hi i would like to ask if there any other way to check if the stator is faulty?
yes sir. sorry for the late reply. u may use a tester. check the three yellow wires. b4 doing it, search on some youtube channels on how to test a tester if it's faulty or not.
Thaaanq so much bro.😍😍😍😍
nadeep romeo no worries. 😀
Bro mine speedometer shows error jr 1.2 something
.. bike is starting but meeter is blank what to do
Hi please know the age of your battery if not yet one year, double check the terminals of your battery, clean it, remove rust. And check connections.
Especially starter relay.
Hi friend, 1 long 7 short Ktm duke 200 2013 abs help out how to fix ?
Check fuse box. Make sure everything is fine. No lose contact or destroyed fuse and if everything is fine, clean your lambda sensor located on the headers, attached. If still the same, try to delete it from the dealer then last option is to change the sensor.
Reverend CowarD Friend, and you can also tell me on the dashboard, where the mode (on the dial) frame changes. How to fix it?
@@mischalivegames what do you mean? What I understand is how to toggle up or down? There are Set and mode buttons.
Reverend CowarD I mean that on the dial (where the mod is installed) on the speedometer (over time, when turned on, a square appears(as interference or a frame) with what can this be related? The rest of the speedometers don't have this.
@@mischalivegames please chat me on my page. Reverend Coward , Facebook.
Also pro one more thing when i but new buttery just when i ride at least 30 mint and thin low electrical and when i try aging start engine but not working until chaneg buttry and same i change 4 buttry and voltage Rectifier Regulator i dont know how i fix it i check all fuse it good why buttry leave??
Most likely it's a symptom with bad stator. But then to make it sure. Much better we go use a diagnostic test for ur bike.
@@reverendcoward7941 ur right sir it was stator not good condition becuse there is spark in the groung for stator.. Thank u so much
@@Ammar99887 very much welcome sir.
My duke200 always miss while i stop at traffic jam could it be the same problem?
Sorry for the late reply sir. Pls check battery voltage while it's on.
Speed and heat is not showing in speedometer. Whats the problem
Hello sir may I know if what else are not showing on the panel aside from those 2 things you've mentioned?
all others are showing my brother
Problem occured after a hvy rain
My KTM 200 Duke no quality at all, first meter screen blank, tank pad jammed, now can’t start.. nice to see but not nice to use .☺️☺️
Dear
My Ktm Rc 200 also same problem so is it issue with stator coil and what is the price can you please confirm
Aadil Syed are u sure same problem on the video my friend? to make sure, pls use tester on ur stator before open the cover. if it's confirmed, buy stator coil.
My rc 200 show jy 1.3.2 2long blink 4short blinks that is ..low or high voltage or implausible voltage .. i change the battery after i cannot start my bike .. then it happen again but i jump started my bike and ride on rpm about like 4 or 6k around 40 minute ..then a miracle happen its doesn't show any of the code anymore and can started like usual .. but i know its gonna happen again so i let my bike rest for while ..
@@harithhazim407 yes jy . 1.3.2 is a battery problem , starting problem also. Yup, low voltage. Just make sure terminals of the battery are clean and tighten well. If it will happen again, check stator.
@@reverendcoward7941 as i told my bike suddenly turn off .. i think it might be the regulator or stator.. just change the battery still show low battery sign ..
@@harithhazim407 Bhai same problem hai MERI bike me what is solution of this error code
El problema es eléctrico
Brother my rc 200 showing 2long and 5short blinks?
Hello bro sorry for the late reply.
Do mind to check ur side stand sensor. Check the magnet if it's still okay or the socket of the side stand sensor. Also check the wires if it's not cut.
@@reverendcoward7941
Okey bro i ll check. Thanks for replay
Yes no worries. Feel free to comment back or update.
@@reverendcoward7941
Sure👍
I checked side stand sensor wiring not found any unusual things.. now i suspect may be the problem occurred with sensor internal short.. or something like that? I disconnect the sensor coupler and bypass with help of a resistor.. now it's not showing any type of error.. but now i noticed another issue.. bike sluggish starting.. idle not steady but after some attempt now it's working okey.. you have any idea about that?
The problem I have is as soon as I start my bike all my coolant goes into my oil and replaced all the seals etc. My heat sensor also dont work replcaed that nd still it doesnt work
What was the problem bro
Y va seguirrr..seguirán... Estoy harto de tantas fallas de las KTM. Lamento haber comprado una KTM. Tremenda decepción de moto. Hasta para venderla se me ha hecho difícil , púes aquí muchos saben qué son unas mierdas de motoras.
Would you mind to translate it to English sir? Thanks.
br0 ..my duke xan self bateryy always low..it need running.
Check the life of the battery, the voltage regulator and the stator coil sir.
JG 1.8.2 code plz tell me whats problem
Still more battery issues. Just try 1st checking your battery terminals or connections. Make sure battery is not too old.
Bhai meri duke 200 raning me band pad jatiye Bar bar
Hii the blinker light is steady in my rc 390 and bike just done 2000 km need help??
Sir just to clarify, is it the flasher u mean For the headlight? Or is it the check engine u mean?
@Jasper Dolphin yes there are times like that. Try these 1st, remove the battery for whole night by the next day, install again the battery. In putting the battery, please make sure to put the positive terminal first then next the negative. Make sure to tighten it but not too much for it not to lose thread. If bike is still under warranty please go to your nearest KTM dealership and let them remove the error by the diagnostic tool. You can always do the thing I said but at your own risk. Ride safe and be cautious enough.
@Jasper Dolphin that's great. That happens on my bike to, battery went low since i haven't use it for a long time because of quarantine but then I do check it time to time like charge the battery at least every twice or thrice a month. Ride safe.
Thanks bro
No worries bro.
1 long and 9 short blink problem tell me please
Please see the description below. Thanks.
Thanks a lot, where you find those check engine light details?
CHANAKYA SINHA searching and inquiries.
My bike shows jg1.7.7 what is the issue
Check ur battery voltage. But before that, try to tighten the terminals of the battery.
22 error code.whats tha solution ??
I'm sorry. No idea about that 22 error code.
bro jg.1.8.2
Are bhai par gadi Band thi switch chalu Karen par high temperature issue dikhara hai OR self nahi bhetraha
Hello , would u mind to translate it to English? Please and thank you. Ride safe
Hello bro, if i may ask, how old is your bike and your battery?
@@reverendcoward7941 Bad English but try
@@reverendcoward7941 Key on and matter look for high temperature issue and those problems start to bike not working self and fuel tank Motor problem started the after fitting bike rellys
@@reverendcoward7941 new battery
Unlessended the wiring problem
Mera duke 200 missing problm ho raha he. Kiya kharab huwa he bataye jara
Hello, English please. Thanks bro ride safe.
@@reverendcoward7941 my duke 200 Bs4 2019 model is given some missing issue like start off when I shifting gear. Engine diagnostic indicator blink 4 long and 3 short but I don't know whats the problem. Please help me out
Hello, can't seem to find it under the description I listed. How many months is your bike? Have let it check to the dealer using the diagnostic tool?
If fuel pump not working then how many time diagnostic light blink
See the description below sir. Thanks for watching.
Bro my duke 200, jg 1.7.4. problem
Sunny Khumancha just clean terminals of battery bro. both positive and negative. use sand paper.
Battery
Mi moto aparese low baterry y anda y se aoga que podra ser
Hi sir, would you mind to say it in English?
What is the problem. JG 1.8.2
It's more on battery. But pls do check 1st if how old is ur battery. If it's not yet even 1 yr, pls clean both positive and negative terminals by sanding it. Make sure properly hand tight of the screws. Check also terminal of relay if it's not loosen. Thanks, pls don't hesitate to update.
Have you got the problem fixed.?
Help my duke 200 1x bling then follow by 5x bling
Check the description sir. Thanks and have a good one.
Bhai 13 code ka problam kya he
Bro speedometer not properly work,can u help mee???
nadeep romeo I'll try. can u give me more situations why not functioning properly?
@@reverendcoward7941 me too .. my speedometer only 50 or 60 something and became 0 sometimes ..
Jass isLove problem with the speed detector. u should let it check to ur nearest ktm company.
Bro engine check light blink stand longly.
What's the prlm??
49 blinks 4 long and 9 short and battery low what should i need to change
Go to ur nearest dealer bro.
If too far, try this 1st :
>Change battery
>If still the same, check stator coil (replace if needed)
> if still the same, since it's idle malfunction, check terminals, clean with contact cleaner .
> better to go to ur nearest dealer and let it get fixed with the KTM mechanics.
bhai mere duke chalo nahi hore kya tum apna phona number deskte ho kya taki may aapko call kar ki bataw mere duke problem
English please sir. Thanks.
What error is jg 5.0.3
Hello, haven't experienced that so far on my bike and sime other bike.
@@reverendcoward7941 thank you its error on my brother rc390
My ktm rc 390 engine light is blinking please help me
14 1990 hi, blinking or just steady?
mine somtimes steady smtimes blink
My acceleration switch off sometimes why any one please fix it
Just acceleration or including the engine? Please tell me more details.
my bike has jg 1.7.7 what do i do?
Captain Ninjazz did you fix problem?
@@jameskray4368 yeah changed the battery
Captain Ninjazz I changed my battery and it still isn’t working
@@jameskray4368 i also changed the stator first that copper coil below the seat
Captain Ninjazz did you
Bro i alredy fitted a new battery but also not working
Cheenu zookies double check everything 1st on the fuse box if there is no blown fuse. if no, use a tester and test ur stator coil wires. better to ask assistance from a good Mechanic. avoid DIY if ever cannot do it or not knowledgeable enough. especially if it's still under warranty. better to bring it to the manufacturer. as much as i know, usually stator problem or might be the starter relay. double check also ur starter relay.
better tell some situations of ur bike why u changed new battery.
@@reverendcoward7941 r
Bro 3 long and 4 short blink
Check the description below bro. Thanks.
G j 1 8 2 error kya isshu h?
What ktm model u have sir?
My bike is showing error jg 1.9.0
That's still a battery issue but let's all check the terminals of the battery first if it's tightened enough. Might be a lose contact. And also check the voltage of the batter if it goes down instead of charging while bike is on.
@@reverendcoward7941 how to check the stator coil is gone or not?
You may use a voltmeter on it but make sure to do it well. I suggest if bike is still under warranty, bring it to the nearest ktm dealer and let it be done there.
Mi moto la prendo y no titila es malo o bueno
Hello sir, do you mind to translate it to English? Thanks.
La mia se queda prendida el chet
My bike does not start after 10 days
Is it brand new sir? What happened before it didn't start?
@@reverendcoward7941 noo it is problem of battery sir i have a question that my bike getting off during low acceleration please tell me the reason
Okay. So clarification, ur bike will turn off during low acceleration? U double check ur clutch cable. Adjust it it properly.
Bhai meri bhi start nhi ho rhi yahi problem h
English please sir. Thanks.
Error jg182 ?
Same bro jg 1.8.2 what is problem??
J.g .1.7.4 what?
Might be dying battery or loose contact. Check battery terminals or connections.
@@reverendcoward7941 denedim olmuyor güç kaynagını degistim olmuyor ekran kapandı
English please. Thanks. Sorry
@@reverendcoward7941 I tried, I did not get any results, I changed the power supply, I did not get any results again, the screen does not show anything at the moment, but the engine is running
@@reverendcoward7941 can you give me your instagram account i will send you a photo
400+ views
ZacMe bwahahaha
Code is 10
On your bike sir?
Bro my rc 390 showing j y 1 3 2
Bro , pls double check battery, battery terminals and lastly stator. I suggest u to go to ur nearest dealership that way the XC-2 gadget can check the main issue. Thanks.
I do had the same problem showing on the display JG 1.7.3.2 and low battery then I checked to nearest KTM service centre they have charged the battery for about 1 & half hour and after that bike starts 2, 3 times and again same problem occurs then I had to replaced new battery later on working fine till 1 week again after that same problem now KTM service centre told me that it's regulator problem the current is not converting to AC to DC and again I had to changed the regulator which cost 1500rs this is my present situation 😥🤯
@@basumatarytravels5019 sorry to hear that. I hope the dealer was using a diagnostic test. Hope not just guessing. Do change ur stator asap to make ur bike okay.