@@BensonAceHardwareBensonPOWER Np, tips for use and filling up real customers wishes. Dont see that much on generic 4wd dealer channels. Happy new year!
This is the kit I have, but you may be able to find the components ala carte,or perhaps find a prewires pigtail with basic crimp connectors if you don't want to invest in the tool. You will need an 8-pin connector: www.amazon.com/JRready-ST6308-Connector-Terminals%EF%BC%8CDT2-Equivalent/dp/B09VXL85SZ/ref=sr_1_4?crid=104PUDFLWBEGN&dib=eyJ2IjoiMSJ9.SHQwxa3ZcpHic3vFnlBlYsfV9cJLr9ZFmnjnmjEu6BQQ1ClECgGo3GXGsqTZ1nygSLNYHLgwEJymSWg0C7uz9Yd9fFX52BF65npVWnyxLULqo0MzQEtnv-AN9skMdTpphlmMYj3tICH2yJIpQ5dqTx2vQ_YOXuMeY6aZmAsj3zOu_qmpn3VIsZfeyv16VFQOOu1Q3ZMCoLAONYzJca_W732P--uYVtg2nSvBXSUg84M.TfZSVC6M-uYyNrbB2u6IPCKSvZyT_9RuAfI2YW3_5C4&dib_tag=se&keywords=deutsch+connector+kit&qid=1728501090&sprefix=duetch%2Caps%2C105&sr=8-4
@@LawrenceWatters this one is set-up with the 2 post frame. What you are experiencing is typical of the 1 post frame. I only sell the 2 post for that reason, however, it does required cutting sometimes if it sticks out too far from the machine. I prefer the rotational stability of the 2 post frame. On your single post frame, do you have a bunch of washers stacked on one side of the mount where it attaches to your machine? If not, it likely came with washers and they were discarded unknowingly, but they were there intentionally to help the machine sit more level when raised.
That is great service 👍
Thank you....cheers!
@@BensonAceHardwareBensonPOWER Np, tips for use and filling up real customers wishes. Dont see that much on generic 4wd dealer channels. Happy new year!
I can't help myself..... always looking for a way to improve the experience if possible.....happy new year!
Appreciate it!
Can you provide a link to the waterproof connector you used on the wiring? Guessing you used an 8 pin connector?
Thank you!
This is the kit I have, but you may be able to find the components ala carte,or perhaps find a prewires pigtail with basic crimp connectors if you don't want to invest in the tool. You will need an 8-pin connector: www.amazon.com/JRready-ST6308-Connector-Terminals%EF%BC%8CDT2-Equivalent/dp/B09VXL85SZ/ref=sr_1_4?crid=104PUDFLWBEGN&dib=eyJ2IjoiMSJ9.SHQwxa3ZcpHic3vFnlBlYsfV9cJLr9ZFmnjnmjEu6BQQ1ClECgGo3GXGsqTZ1nygSLNYHLgwEJymSWg0C7uz9Yd9fFX52BF65npVWnyxLULqo0MzQEtnv-AN9skMdTpphlmMYj3tICH2yJIpQ5dqTx2vQ_YOXuMeY6aZmAsj3zOu_qmpn3VIsZfeyv16VFQOOu1Q3ZMCoLAONYzJca_W732P--uYVtg2nSvBXSUg84M.TfZSVC6M-uYyNrbB2u6IPCKSvZyT_9RuAfI2YW3_5C4&dib_tag=se&keywords=deutsch+connector+kit&qid=1728501090&sprefix=duetch%2Caps%2C105&sr=8-4
Hello. What's the size of these front tyres ?
@@ThomasDuthu I believe they were 30"
@@ThomasDuthu 26x9x14
How do you. Get it to raise up even
A winch is required to raise and lower the machine
@@BensonAceHardwareBensonPOWER I have a winch but when raining it the side with engine on it hangs down about 4 inches
Do you have the single post or two post subframe?
@@BensonAceHardwareBensonPOWER single post
@@LawrenceWatters this one is set-up with the 2 post frame. What you are experiencing is typical of the 1 post frame. I only sell the 2 post for that reason, however, it does required cutting sometimes if it sticks out too far from the machine. I prefer the rotational stability of the 2 post frame. On your single post frame, do you have a bunch of washers stacked on one side of the mount where it attaches to your machine? If not, it likely came with washers and they were discarded unknowingly, but they were there intentionally to help the machine sit more level when raised.