Chain and Sprocket Replacement Guide: Honda CBR500R / CB500F / CB500X
ฝัง
- เผยแพร่เมื่อ 29 ต.ค. 2022
- How to replace chain and sprockets Honda cbr500r, cb500f, and cb500x with tool sizes and torque specs.
NOTE: over the years I've found that regular spray bottles don't last when using Kerosene. I recommend using a chemical resistant spray bottle. I got one from Walmart for about $11 and it's been holding up for at least a couple years now.
LINKS:
Chain (custom colors): sprocketcenter.com/i-30499462...
Chain (basic): amzn.to/3SP9Tiu
Front sprocket (15T): amzn.to/3LlW8p0
Front sprocket (16T): amzn.to/4c0Xpzg
Rear sprocket (41T): amzn.to/3rCoMtZ
Rear sprocket (43T): amzn.to/3Biix1N
Impact driver: amzn.to/3tC97vN
Angle Grinder: amzn.to/3DoTbAI
Chain tool: amzn.to/3HI5CbJ
Breaker bar: amzn.to/348rIWD
Torque wrench (3/8” drive): amzn.to/3ooqxJl
Torque wrench (1/2” drive): amzn.to/3HqCZjq
Socket wrench set: amzn.to/3EP9kBW
Socket extensions: amzn.to/3TkyTPS
24mm socket: amzn.to/3Ci5YWf
Impact socket set: amzn.to/3ux1WEm
Wrench set: amzn.to/32T9pE2
Ratcheting wrench set: amzn.to/32SN2hY
Hex wrench set: amzn.to/32U647P
Bits and driver: amzn.to/34v0Dg7
Needle nose pliers: amzn.to/3L7jvCv
Bent nose pliers: amzn.to/3J0YffT
Flat head screwdriver: amzn.to/3J3azft
Plastic mallet: amzn.to/3HBYRYU
Tape measure (SAE): amzn.to/36Fd3TX
Tape measure (metric): amzn.to/3Lnw8bO
Motorcycle stands: amzn.to/3rv1gyA
Rolling stool: amzn.to/36KSJQZ
Drop light: amzn.to/3uoiwIo
Nitrile gloves: amzn.to/3IUg00c
Padded gloves: amzn.to/36WLk1b
Face shield: amzn.to/3zvmLmW
Ear plugs: amzn.to/3SKyDIx
Safety glasses: amzn.to/35AO9ns
Kerosene: amzn.to/3GmUqQr
Spray bottle: amzn.to/3L7eWby
Chain brush: amzn.to/3HoVtRa
Chain lube: amzn.to/3L6WejZ
Waterproof grease: amzn.to/3xwXkQ9
Painter’s tape: amzn.to/3gr2k0t
Rags: amzn.to/3J6prtT
Tail tidy: amzn.to/3UTy7JQ
Rear tire hugger: amzn.to/3ZIz4rC
Amazon Prime Student Discount: amzn.to/3YzZNXk
Amazon Prime Discount for people with SNAP, Medicaid, etc.: amzn.to/3sfQpvW
Want to help the channel grow?
Support me on SubscribeStar: www.subscribestar.com/endless...
Support me on Patreon: / endlessmoneypits
Check out my merch!: endless-money-pits.myspreadsh...
Or make a one-time donation: paypal.me/EndlessMoneyPits?lo...
TOOLS AND SUPPLIES USED:
• Breaker bar
• A couple torque wrenches
• Socket wrench
• Short socket extension
• 24mm socket
• 19mm socket
• 17mm socket (impact)
• 14mm socket (impact)
• 19mm wrench
• 14mm wrench
• 12mm wrench
• 10mm ratcheting wrench
• 5mm hex bit
• Needle nose pliers
• Bent nose pliers
• Flat head screwdriver
• Plastic mallet
• Measuring tape
• Impact driver
• Chain tool
• And an angle grinder
• A motorcycle stand
• A stool
• A light
• Rubber gloves
• Padded gloves
• A face shield
• Ear plugs
• Safety glasses
• Kerosene
• Spray bottle
• Chain brush
• Chain lube
• Waterproof grease
• Tape
• Rags
• Some cardboard to work on
• And a new chain and sprocket set (Front 15T, Rear 43T)
Music not provided by TH-cam:
“Song E01” by Seth Schneider
sethds93@gmail.com
**This video description contains affiliate links, which means that if you click on one of the product links and make a purchase, I'll receive a small commission at no additional cost to you. This helps support the channel and allows me to continue making videos like this.
*Disclaimer*
Due to the litigious world we live in, I have to include this statement:
I cannot guarantee against improper use or unauthorized modifications of this information. The creator of this content assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. I recommend safe practices when working on vehicles and or with tools seen or implied in this video. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not the creator of this content. - ยานยนต์และพาหนะ
Hey thanks for the clear vids! So with the bigger sprocket you should have ordered a 111 link chain plus the master or is the 112 correct plus the master? Thanks man!
112 is the stock chain size. The blue chain I installed with a bigger rear sprocket should have been 114 links including the master link, but they sent me 114 links plus a master link which is why it came out too long.
Thanks for this really pro video. Clear video where you can find all info. I was able to find info on this which was requested by the bloke Who has been fixing bikes for 40 years.
Thank you, I'm glad you found it helpful!
Great video, the camera angles are really good, very helpful thanks!
Sometimes I wonder why I spend so much time on these videos but I'm glad people appreciate them. Thank you.
Love all your videos mate. Very informative and helpful. Thank you for all your hard work.
Thank you! Trying to get back on track after a big move. Thanks for the support.
6:52 reference- “Once you get the wheel, collars, chain tensioners, swing arms AND ALL 9 PLANETS IN ALIGNMENT… “. 😅 👊🏼
Thank you for your guides. You deserve a lot more views and subscribers, keep up your work!
It's a long road but I won't give up. Thanks again for your support!
I’ve checked the specs on west coast Honda site , I’ve got a Honda cbr 500r 2014 abs model and they say it goes that way .
@@chadedwards5316 It looks to be the same parts diagram on the West Coast Honda site. You have to look very closely, #4 goes on the brake side, and #5 which is the asymmetrical spacer goes on the chain side. That's the way I installed them. www.westcoastmotorcycles.com.au/partFinder/fiche/honda/2014/cbr500ra/rear-wheel#next
@@EndlessMoneyPits I’ve watched your video over and over again and you can see that the flat silver spacer goes to the ABS / brake side . The black one with flailed end spacer goes to the sprocket side, by the way your video was very helpful with the torque settings and the step by step removal and installation,also replacing the chain and rivet link👍
Yes, that's the way I said they should go, or at least that's why I've been trying to say. Sorry for any confusion.
Thank you man.
I have this exact model. Thank you so much for the guidance! Very clear and concise!
Glad to help! There aren't many good videos out there on these bikes.
I couldn’t decide if I should get the angle grinder or dremmel. I went with dremmel. Maybe that angle grinder works better. Good video. Haha. “Gently remove the axle.”
If I didn't have the angle grinder I would have tried my Dremel. Glad it worked! And thank you.
Check the chain slider every time you replace the chain set as well. The rubber dry rots surprisingly fast
I don't remember if I mentioned that in the video but I did buy a new chain slider and haven't installed it yet. The original one still looked mint at the time of filming this. Good to always check it.
What mudguard do you have installed in the rear ? Looks nice
It's the PowerBronze rear tire hugger. I just added a link for it in the description of this video. Works great for keeping the rear shock clean.
Beautiful 500R! Have you ever taken it for a track day?
Thank you! No, I have not yet but maybe someday. The bike got a little scraped up during our move so I need to find some touch up paint if possible.
@@EndlessMoneyPits are you still in the valley? I’ve had my cb500r for about a year now and have yet to see another in the valley. Always riding from Corvallis to Salem
No, we moved to Arkansas in November. I think I saw a couple 500r riders in the McMinnville area but never got a close look. The Willamette Valley is such a better place to ride. The traffic here is kinda intense.
Can we clean and lube the chain and sprockets before installation?
I don't see why not, but it would be messier and harder to work with since everything will be slippery.
So, if we use 41 rear and 15 front sprocket, ordering the 112 link chain with master link, do we have to remove one more link? Since that would add up to 113? Seems like a mess. Thank you.
Removing one more link from the chain before putting it on is not easy. I wanted to ride this to a trip tomorrow. Not gonna work.
112 is the stock chain size. The blue chain I installed with a bigger rear sprocket should have been 114 links including the master link, but they sent me 114 links plus a master link which is why it came out too long. You should be able to cut a link off without connecting the chain, just lay the chain across the rear sprocket to hold it while you cut.
Does it work With a chain thats already closed? Or do you always need an open chain ?
I'm not sure I understand the question.
Do you happen to know the torque specs for the gear shifter bolt when reinstalling?
I don't believe there is one (in the service manual, at least). I try to include all torque specs available in my videos.
@@EndlessMoneyPits thank you for the replying 🙂
Hi.
Can you tell me how this bike's speedometer measures top speed?
Wheel?
Gearbox?
ty
Gearbox. If measured at the wheel then my speedometer would still be correct after making this change, but it's off by about 8%
@@EndlessMoneyPits Thanks a bunch man, I wanted to know what I was in for,👍
How does the rear sprocket feel with the 2 extra teeth? Does it feel like longer gearing?
I honestly can't tell much of a difference in torque but my MPG dropped from 70 to 60.
@@EndlessMoneyPits no kidding 😆 i think ill stick with whats on it now. Think ill be replacing mine soon.
I plan to go back to stock or possibly longer gearing than stock once this set wears out.
What kind of stand is that?
There are links in the description for everything.
Dude, did u reach 115mph with 15/43 sprocket setup?
I think my bike topped out around 105-108 mph with the stock sprockets. Accurate speedometer checked by GPS. The new gearing is slower but I haven't topped it out.
Does changing the sprocket to a bigger size make it go faster?
A bigger rear sprocket should make it accelerate faster but will have a slower top speed.
@@EndlessMoneyPits what if I only changed the from not the rear. Thinking 17t front sprocket. Looking for more top speed
Yes, a bigger front sprocket (if it fits) will give more top speed but slower acceleration.
Where do i find a 16 tooth sprocket????? You offer no links for that!
I didn't supply a link for a 16 tooth sprocket because I didn't use a 16 tooth sprocket, but I just found a link to one and added it to the video description for you.
Hi thank you!!! But I still can’t find a lead! Still, I love your work!!!
It's the 4th link in the video description under "LINKS". Thank you and have fun out there!
How do I reinstall install the front spacers?
I show the orientation in the video when I'm cleaning them but getting everything lined up when sliding the axle through can be a little tricky if that's what you mean. Just have a little patience.
At 4:19 you have 2 collars labeled front. I must have misplaced them because I can’t find them at all. I’m just wondering if they’re for something else or if I need to order replacements.
Oh right, the front ones are interchangeable. Yes, if you're missing them you'll definitely need to find some replacements.
@@EndlessMoneyPits So do those front collars go on the rear axle or somewhere else?
No, I meant they are interchangeable from left to right.