Hi friend, I am using this and works perfectly: MGS12-SF www.frynetworks.com/product-page/upgraded-outdoor-satellite-miner-2-way-long-range-cable-splitter In the video description you can find all the rest of equipment
Any chance we can run stream server (strsvr) on a raspberry pi or other ultra small device and still broadcast gps readings and could be installed close to the geodnet receiver ?
@@garfpt Hi, the guide is about the PC (in addition to being easy for everyone) also to be able to do all the possible DePIN GNSS including FRY. For a raspberry or other I don't know how to advise you
Hi, this is my video guide for GNSS Multimining which also includes RTKDirect. I don't have other setups/guides that are easy (for everyone) in mind, in the future I will also release how to upgrade for this equipment/configuration
I don't understand how you can get the signal from geodnet antenna and split with 3 outputs: hyfix, fry USB card and um980. Can you share a simple schematic or drawing. Thank you
Hi, I am using the Geodnet antenna for the Hyfix and for the UM989/982 via a two-output splitter. For FRY I am using the Outdoor Satellite Breaking Board with its supplied antenna. For a scheme you can see at minute 3:07
@@Michael-sq1zs RTK tokens and after onboarding you will already start receiving them, the connection with wallet to make the claim (and then also swap) will be released in a few weeks
Hi mate, registered and went online for a few seconds , stays online for a few seconds then becomes inactive and so on. Do you know why is that happening? It does generate rewards. Using an Ntrip-x board. Thank you!
Hi friend, the problem is the installed NTRIP-X software which doesn't allow the connection with STRSVR. You could try doing a flash to remove the NTRIP-X software and in the worst cases you can do a reset if you see that it doesn't work (but honestly I don't recommend it, anyway it's your choice). I hope that in the future GNS-Electronics will add 2 NTRIP in its software
@@arverneexploration766 Hi, if you buy the FRY (PC) Miner Outdoor you don't need the license. And you have double the rewards compared to the BYOD license
Follow all steps on your EXCELENT guide. Get it to work with a UM980 and a sparkfun GNSS Antenna Splitter (Power Divider) with DC Pass. All good with FRY Outdoor GPS Miner and Onocoy Station. Have problem with RTKDirect, as it shows bad password all the time. I think I might be confused between Hotspot username and password and NTRIP Accounts in base station detaisl... Do you know with one to use? THANKS for this video an for all the help you provide to the comunity with your guides
Just one more question: What miner should I put on Onocoy registration when it asks me what GNSS reference station I have? Should I choose NTRIP-X ? They only have ArdusimpleRTK2B ArdusimpleRTK3B SparkFun RTK mosaic-X5 GNS NTRIP-X ComNav Hemisphere Hexagon Leica JAVAD NavCom NovAtel SunNav Topcon Trimble Other
what a Great video, cant wait to get all the hardware and start. thank you Osvaldo
Hi. For the antenna splitter there are different options to choose from regarding gain...which one to choose for a 2way splitter? Any idea? Thank you
Hi friend, I am using this and works perfectly:
MGS12-SF www.frynetworks.com/product-page/upgraded-outdoor-satellite-miner-2-way-long-range-cable-splitter
In the video description you can find all the rest of equipment
Holy Moly....I will start with one. lol. Not for the faint of computer heart.
First to watch and second
Hi mate 👋
Great video
Any chance we can run stream server (strsvr) on a raspberry pi or other ultra small device and still broadcast gps readings and could be installed close to the geodnet receiver ?
@@garfpt Hi, the guide is about the PC (in addition to being easy for everyone) also to be able to do all the possible DePIN GNSS including FRY. For a raspberry or other I don't know how to advise you
What about the video on using budget parts for RTKDirect?
Hi, this is my video guide for GNSS Multimining which also includes RTKDirect. I don't have other setups/guides that are easy (for everyone) in mind, in the future I will also release how to upgrade for this equipment/configuration
I don't understand how you can get the signal from geodnet antenna and split with 3 outputs: hyfix, fry USB card and um980. Can you share a simple schematic or drawing. Thank you
Hi, I am using the Geodnet antenna for the Hyfix and for the UM989/982 via a two-output splitter. For FRY I am using the Outdoor Satellite Breaking Board with its supplied antenna. For a scheme you can see at minute 3:07
🤑
What tokens do you get for mining rtk direct? There isnt a wallet or anything
@@Michael-sq1zs RTK tokens and after onboarding you will already start receiving them, the connection with wallet to make the claim (and then also swap) will be released in a few weeks
Hi mate, registered and went online for a few seconds , stays online for a few seconds then becomes inactive and so on. Do you know why is that happening? It does generate rewards. Using an Ntrip-x board. Thank you!
Hi friend, the problem is the installed NTRIP-X software which doesn't allow the connection with STRSVR. You could try doing a flash to remove the NTRIP-X software and in the worst cases you can do a reset if you see that it doesn't work (but honestly I don't recommend it, anyway it's your choice). I hope that in the future GNS-Electronics will add 2 NTRIP in its software
fry need buy License ?
@@arverneexploration766 Hi, if you buy the FRY (PC) Miner Outdoor you don't need the license. And you have double the rewards compared to the BYOD license
Follow all steps on your EXCELENT guide. Get it to work with a UM980 and a sparkfun GNSS Antenna Splitter (Power Divider) with DC Pass.
All good with FRY Outdoor GPS Miner and Onocoy Station.
Have problem with RTKDirect, as it shows bad password all the time. I think I might be confused between Hotspot username and password and NTRIP Accounts in base station detaisl... Do you know with one to use? THANKS for this video an for all the help you provide to the comunity with your guides
@@garfpt Thanks friend, you need to enter Mountpoint and password that appear on your RtkDashboard. This one 4:40
@@ilCapoFox Yes. I figured out tha the STRSVR for RTKDirect only needs Mountpoint Name and Password. Thank you
Just one more question: What miner should I put on Onocoy registration when it asks me what GNSS reference station I have? Should I choose NTRIP-X ? They only have
ArdusimpleRTK2B
ArdusimpleRTK3B
SparkFun RTK mosaic-X5
GNS NTRIP-X
ComNav
Hemisphere
Hexagon
Leica
JAVAD
NavCom
NovAtel
SunNav
Topcon
Trimble
Other
@@garfpt Other
@@ilCapoFox If I choose "Other" then it asks me for the stations name. Should I put UNICORE UM980 ?
@@garfpt Exactly 👍