Exhaust Manifold Coating with Eastwood High Temp Coating

แชร์
ฝัง
  • เผยแพร่เมื่อ 24 ธ.ค. 2024

ความคิดเห็น • 133

  • @bryco32
    @bryco32 2 ปีที่แล้ว +2

    I used this on my amc 304 manifolds and a 150cc scooter I have had since 2011. I used the below method with my manifolds. I bead blasted and baked my manifolds in the raw at 400 deg for 10 minutes after the oven was warmed up.. I let them cool and used the eastwood coating shown here. I painted as per the specs on the can. After a week or so fired up my propane bbq and got it up to temp. (didn't have a chance until then to bake them) Then I set them on the grate at 400 deg and baked them for 15 or so minutes each then threw them on the jeep and they have been fine ever since. The finish went to a matte finish but that was expected. I liked it so much I used it on a gy6 150cc scooter header I had . The Scooter header pipe I bead blasted and just brushed the paint on. No preheat since it was new and never had any oils or contaminants on it.. I installed it and fired it up and let it run until the smoke dissipated off the header from the paint. It stunk so I had it out in the open with a fan set to low to blow onto the bike I let it cool and started riding it daily for several years. It went matte and has stayed the same since. No rust or anything. This crap works. Hopefully they never change the formula. One can did all three exhaust parts. With plenty left over.. I used a foam paint brush for all parts. 2 coats on everything. One coat till it dried to the touch and another after that. I waited a week after I painted the manifolds to put them into the heat for 15 minutes..

    • @PetesGarage
      @PetesGarage  2 ปีที่แล้ว +1

      That's awesome! Thanks for sharing

  • @davidcollis4758
    @davidcollis4758 5 ปีที่แล้ว +3

    Pete, I can't believe you were working on a classic beauty without fender covers!

  • @jake-hy2zb
    @jake-hy2zb 5 ปีที่แล้ว +2

    Thanks Pete. This is an older one I missed and sorry I did. My new headers are ceramic so should be good but I have so many projects I'll be using this. As someone said, Master Tech.

    • @PetesGarage
      @PetesGarage  5 ปีที่แล้ว +1

      Headers get really hot, this paint may not hold up to that

  • @dcal3745
    @dcal3745 6 ปีที่แล้ว +3

    I havent tried the eastwood but just last week i used the POR-15 high temp on my olds thorton 350 jr exhaust. Will see how that holds up. Supposed to be good up to 1500 degrees

    • @AustrianAnarchy
      @AustrianAnarchy 6 ปีที่แล้ว +1

      That is another product I was hoping to see a long term report on.

    • @PetesGarage
      @PetesGarage  6 ปีที่แล้ว +1

      I will try the POR and let everyone know.

    • @davidcollis4758
      @davidcollis4758 5 ปีที่แล้ว

      D Cal I just bought the same set of manifolds for my 68 Cutlass. I wanted to coat them while they are still new.

  • @Pendaws
    @Pendaws 6 ปีที่แล้ว +2

    Good job and I love the music. :)

  • @larrywoolford8978
    @larrywoolford8978 6 ปีที่แล้ว +4

    No broken exhaust manifold bolts ! What sorcery do you practice ?

    • @PetesGarage
      @PetesGarage  6 ปีที่แล้ว +1

      I rebuilt this engine 2 years ago so everything is nice and rust free.

  • @CarlosLopez-tt5py
    @CarlosLopez-tt5py 6 ปีที่แล้ว

    Another practical video from the Master tech . I want to move close to your shop Pete , i have a old dodge that need all your expertice thxs for sharing.

    • @PetesGarage
      @PetesGarage  6 ปีที่แล้ว

      Thanks Carlos, I don't think you want to live close to Buffalo, NY right now...lol

  • @asiasmaster
    @asiasmaster 4 ปีที่แล้ว

    That's awesome i will be using this product on my new headers on my 67 firebird.

    • @PetesGarage
      @PetesGarage  4 ปีที่แล้ว

      I hope it works for you

  • @AustrianAnarchy
    @AustrianAnarchy 6 ปีที่แล้ว +1

    I've been waiting for someone to do this! Thanks! Hope you do a followup on this in the future.

    • @PetesGarage
      @PetesGarage  6 ปีที่แล้ว +1

      I will follow up this summer on it

  • @RebornRider1983
    @RebornRider1983 ปีที่แล้ว +2

    Hello! How is the exhaust manifold now? Can the paint really withstand the heat? Thanks for answering.

    • @PetesGarage
      @PetesGarage  ปีที่แล้ว +3

      Is is great, holds up very well

  • @jerryneal-dnr731
    @jerryneal-dnr731 4 ปีที่แล้ว +3

    Pete, Thanks for the tip. I plan to use this coating on my Chevy Ram Horns. Question: Do you recommend using a gasket when reinstalling these manifolds? I don't believe Chevy used gaskets on these from the factory. Just curious if I should purchase Felpro gaskets to use when I reinstall these on my Corvette. Thanks!

    • @PetesGarage
      @PetesGarage  4 ปีที่แล้ว

      I did use a gasket. It's a good idea to make up for expansion differences. They a know to crack

  • @marvelharris9540
    @marvelharris9540 3 ปีที่แล้ว +2

    How is it holding up... I used cerakote and the heat caused it to crack and bubble within 100 miles

    • @PetesGarage
      @PetesGarage  3 ปีที่แล้ว +3

      These still look great after a couple years

  • @abolperme7042
    @abolperme7042 6 ปีที่แล้ว +1

    Thank you man, I was wondering how to deal with my rusty exhaust manifold.

    • @PetesGarage
      @PetesGarage  6 ปีที่แล้ว

      This works really well

  • @Sickofsociety1
    @Sickofsociety1 6 ปีที่แล้ว +1

    Nice job buddy!

  • @turnipsucks6416
    @turnipsucks6416 6 ปีที่แล้ว +2

    Surprise...No dislikes. (Actually, not really a surprise). Fantastic video, and thanks for the update/info.

    • @PetesGarage
      @PetesGarage  6 ปีที่แล้ว

      Oh don't worry, those 2 guys will be around soon

  • @محمدالفضلي-ز5ك
    @محمدالفضلي-ز5ك 6 ปีที่แล้ว +2

    Hi! how are you. What is the difference between Block 350 and Block 305 and what is the best in performance

    • @PetesGarage
      @PetesGarage  6 ปีที่แล้ว +1

      350 is the best for performance because there are more parts available. A 305 has a smaller bore and several differences.

    • @محمدالفضلي-ز5ك
      @محمدالفضلي-ز5ك 6 ปีที่แล้ว +1

      Pete's Garage thank you my friend

    • @ShainAndrews
      @ShainAndrews 5 ปีที่แล้ว +1

      No replacement for displacement.

  • @aaronbrenneman1513
    @aaronbrenneman1513 5 ปีที่แล้ว +1

    I tired that on manifolds but it burnt off right away and didnt last at all. But I did the whole system and it still looks new.

    • @PetesGarage
      @PetesGarage  5 ปีที่แล้ว +1

      Interesting. Was it a high heat application like headers? Those will get too hot for this product

    • @aaronbrenneman1513
      @aaronbrenneman1513 5 ปีที่แล้ว +1

      @@PetesGarage yeah it's for manifolds but it didnt seem to cure very good. I dont drive the truck often anyways but the motors nice and painted with brown manifolds.

  • @475george
    @475george 6 ปีที่แล้ว +1

    Awesome I’m going to get it a try!

    • @PetesGarage
      @PetesGarage  6 ปีที่แล้ว

      It's very reasonably priced

  • @byler390
    @byler390 2 ปีที่แล้ว

    Looks incredible, thanks

  • @garagehack2060
    @garagehack2060 6 ปีที่แล้ว +3

    Will it work on headers?

    • @Dr_Xyzt
      @Dr_Xyzt 6 ปีที่แล้ว +2

      I'm with Paul. Is it like a ceramic coating?

    • @PetesGarage
      @PetesGarage  6 ปีที่แล้ว

      It's good up to 1400F, my headers never get about 1150 so I would say yes.

    • @garagehack2060
      @garagehack2060 6 ปีที่แล้ว +1

      Thanks Pete.

  • @merdoggalex6858
    @merdoggalex6858 6 ปีที่แล้ว

    I love this channel

  • @woog74
    @woog74 2 ปีที่แล้ว +1

    getting ready to do the manifolds on my C2 soon. Did you wipe these down with lacquer thinner or something of that nature after the blasting? Also, when it says have the parts warm, did you preheat them in an oven before applying the paint?

    • @bryco32
      @bryco32 2 ปีที่แล้ว +1

      Doesn't look like you got a reply so here is my take. I used this on my amc 304 manifolds and a 150cc scooter I have had since 2011. I used this exact same method with mine. I bead blasted and baked my manifolds in the raw at 400 deg for 10 minutes after the oven was warmed up.. I let them cool and used the eastwood coating shown here. I painted as per the specs on the can. I Then fired up my propane bbq and got it up to temp. Then I set them on the grate at 400 deg and baked them for 15 or so minutes each then threw them on the jeep and they have been fine ever since. Finish went to a matte finish but that was expected. The Scooter header pipe I bead blasted and just brushed the paint on. No preheat since it was new and never had any oils or contaminants on it.. I installed it and fired it up and let it run until the smoke dissipated off the header from the paint. It stunk so I had it out in the open with a fan set to low to blow onto the bike I let it cool and started riding it daily for several years. It went matte and has stayed the same since. No rust or anything. This crap works. Hopefully they never change the formula. One can did all three exhaust parts. With plenty left over.. I used a foam paint brush for all parts. 2 coats on everything.

  • @chrispiazza7487
    @chrispiazza7487 6 ปีที่แล้ว +1

    Hi Pete. Wondering how long does one have after coating before turning the engine over for cure? I've got a Studebaker engine I'm building right now but I don't have any idea when it'll be ready to fire. I do have a big oven I could bake it in but I'm worried about warp. Any thoughts?

    • @PetesGarage
      @PetesGarage  6 ปีที่แล้ว

      Great question! It dries so you can install it, so I would assume it can sit until you start it. You could bake it as long as you get it to the recommended temperature. I would not worry about warps, it won't get that hot.

    • @chrispiazza7487
      @chrispiazza7487 6 ปีที่แล้ว +1

      Thanks for the reply! I'll order up some paint tomorrow.

  • @srreventon
    @srreventon 4 ปีที่แล้ว +5

    I have coated many manifolds
    My opinion is
    Sand blast the pieces
    Spray brake cleaner to clean before painting
    Use heat gun to heat manifolds before painting
    Go to homedepot and buy their spray can.. it has a compressed this can with a glass container in the bottom.. uncrew the bottom and add your paint
    Make sure the metal has been heated and its warm then spray it.. i usually do 2 coats
    Let dry over night amd install and idle for 1 hour
    The smoke is toxic and it will smell while its being cured

    • @PetesGarage
      @PetesGarage  4 ปีที่แล้ว +1

      Great comment, thank you

  • @joseantoniodaly4875
    @joseantoniodaly4875 ปีที่แล้ว

    i need something that reduces engine bay temperature a lot, so i need to insulate heat from turbo manifolds as much as possible. The options are, the coatings from Eastwood, flameproor by VHS, and cerakote coatings that are more expensive. Whats a best way without spending to much?

    • @PetesGarage
      @PetesGarage  ปีที่แล้ว

      Get them ceramic coated

    • @joseantoniodaly4875
      @joseantoniodaly4875 ปีที่แล้ว

      @@PetesGarage im overseas, i have to buy a kit. Which one can i buy?

  • @AustrianAnarchy
    @AustrianAnarchy 6 ปีที่แล้ว +1

    Have you had any luck with ceramic coated headers, either from the factory (TTI, etc) or sending them out for ceramic?

    • @PetesGarage
      @PetesGarage  6 ปีที่แล้ว +1

      I have sent things for ceramic. It does work, but nothing is forever.

  • @breadoutherass4759
    @breadoutherass4759 5 ปีที่แล้ว +1

    After spraying the inside can you let them air cure for 8-12 hours? An is one can enough to do each side of exhaust manifolds??

    • @PetesGarage
      @PetesGarage  5 ปีที่แล้ว

      You do not do the inside, only the outside. It cures overnight.

    • @breadoutherass4759
      @breadoutherass4759 5 ปีที่แล้ว

      I have stainless manifolds and I heard that if you do not ceramic coat the inside that they will rust from the inside out. Is that true??

    • @PetesGarage
      @PetesGarage  5 ปีที่แล้ว

      You don't need to coat stainless at all

    • @Nowayjose-z2r
      @Nowayjose-z2r 5 ปีที่แล้ว

      @@breadoutherass4759 If they are stainless then they shouldn't rust from the inside out. If they have a stainless coating (possible, but weird) maybe. The heat generally keeps them from deteriorating rapidly. With that said all metals corrode even aluminum it all about at what rate and how fast.

  • @Lumpygrits76
    @Lumpygrits76 4 ปีที่แล้ว +2

    Mannnnnnn I tell ya. I ran across this looking for high temp painting tips and this stuff looks like it will definitely get the job done. But I’m gonna be building a wood burning fire pit out of a big 4 foot wide propane tank end cap and was looking for something that would hold up to the temp and weather. I think I found it 👍🏼👍🏼. And I think I’m going to brush it on both inside and outside.

    • @PetesGarage
      @PetesGarage  4 ปีที่แล้ว +1

      It holds up very well. Rustoleum makes a great black high heat for grills

    • @Lumpygrits76
      @Lumpygrits76 4 ปีที่แล้ว

      Pete's Garage I want it with a little bit of gloss to it so it’s got a little bit of a powder coat look. I’m thinking of something like a hammered bronze or iron look to it without any rust.

    • @PetesGarage
      @PetesGarage  4 ปีที่แล้ว

      I like it

  • @BlackTownie999
    @BlackTownie999 3 ปีที่แล้ว

    How did they hold up? I need to do something about my manifolds for my 4.6, they are Fugly! I don't have a sandblaster so I'm using electrolysis and a wire brush to get the rust off...

    • @PetesGarage
      @PetesGarage  3 ปีที่แล้ว +2

      They held up very well

  • @davidwilson7716
    @davidwilson7716 3 ปีที่แล้ว +1

    How many coats did you put on and hoe many pints of paint did you use on these manifolds?

    • @PetesGarage
      @PetesGarage  3 ปีที่แล้ว +2

      2 coats with a foam brush

  • @ronsre-creations5289
    @ronsre-creations5289 4 ปีที่แล้ว

    Hi Pete, If you were to use this on an older in good shape exhaust system. Does it have to be baked right away ? Couldn't it or would it be ok until the system was re-installed and then baked when it was finally time to run the motor. In other words does it have to be baked the next day (time window or it will fail) ?

    • @PetesGarage
      @PetesGarage  4 ปีที่แล้ว +1

      You can put it on and leave it, no problem.

    • @ronsre-creations5289
      @ronsre-creations5289 4 ปีที่แล้ว

      @@PetesGarage Thanks, Good to know.

  • @Backyardrust49
    @Backyardrust49 5 ปีที่แล้ว +2

    How has it lasted so far

  • @joseantoniodaly4875
    @joseantoniodaly4875 ปีที่แล้ว

    how much temperature does that coating drops down ?

    • @PetesGarage
      @PetesGarage  ปีที่แล้ว +1

      I don't think it's measureable

  • @bestbuildpc
    @bestbuildpc ปีที่แล้ว

    I can not find this paint in the nederland. Which temp I need to use?

  • @merrittmcdowell8675
    @merrittmcdowell8675 5 ปีที่แล้ว +2

    Any long term update.?

    • @PetesGarage
      @PetesGarage  5 ปีที่แล้ว +4

      Yup.....still looks awesome after a summer of crusin'

  • @tizkool
    @tizkool 10 หลายเดือนก่อน

    Did you do the bolts also?

    • @PetesGarage
      @PetesGarage  10 หลายเดือนก่อน

      I did, after I torque them down

  • @milenkogt
    @milenkogt 4 ปีที่แล้ว

    Will this help reduce underhood temps or is this mainly a corrosion resistant coating?

    • @PetesGarage
      @PetesGarage  4 ปีที่แล้ว +1

      Mostly a corrosion protection

    • @darrentylor5473
      @darrentylor5473 4 ปีที่แล้ว +2

      And to make em pertty

  • @ibrahimeltony4865
    @ibrahimeltony4865 4 ปีที่แล้ว +2

    Hi Pete .. is it still holding?!

    • @airbornepotato
      @airbornepotato 4 ปีที่แล้ว

      I want to know as well.@pete

    • @PetesGarage
      @PetesGarage  4 ปีที่แล้ว +2

      It still looks great!

  • @oscarvillarreal8951
    @oscarvillarreal8951 3 ปีที่แล้ว +2

    Where can I go to sand blast my headers?

  • @raylyd
    @raylyd 5 ปีที่แล้ว

    would this work to coat my exhaust as i have a car exhaust no longer made and was thinking of giving it a coat.

  • @randyjohnson3970
    @randyjohnson3970 3 ปีที่แล้ว

    Recoating studebaker exhaust manifolds without fender covers on that nice black paint? Dragging the air hose over that paint? Wow! What to think.

    • @PetesGarage
      @PetesGarage  3 ปีที่แล้ว +1

      I'm more careful than you think

  • @goldengeologist9834
    @goldengeologist9834 6 ปีที่แล้ว +1

    Cool!

  • @darrentylor5473
    @darrentylor5473 4 ปีที่แล้ว

    Could you just oven bake them at 350 for 20min if your project isn't running at the moment?

    • @PetesGarage
      @PetesGarage  4 ปีที่แล้ว +1

      You could, but I'd go to 500

    • @ronsre-creations5289
      @ronsre-creations5289 4 ปีที่แล้ว

      @@PetesGarage Hi 500 for 20 minutes ? Thanks

  • @benjamine.7102
    @benjamine.7102 6 ปีที่แล้ว +2

    What happened to the rock music?

    • @PetesGarage
      @PetesGarage  6 ปีที่แล้ว

      Well, I gotta fit the music to the work. I get back into the rock

  • @doantaylor9561
    @doantaylor9561 11 หลายเดือนก่อน

    Can i use primer paint?

  • @johnnyyankee8604
    @johnnyyankee8604 4 ปีที่แล้ว +1

    How many miles have you put in the car so far? Can you do a quick update video?

    • @PetesGarage
      @PetesGarage  4 ปีที่แล้ว +1

      It has a solid 2 years on it. Next time I see the owner I will

  • @dateatorjr9671
    @dateatorjr9671 6 ปีที่แล้ว +3

    Time will tell...

  • @joehovanec1985
    @joehovanec1985 5 ปีที่แล้ว +9

    Pete, stop using Fram oil filters, unless your goal is to use the worst oil filters made.

    • @PetesGarage
      @PetesGarage  5 ปีที่แล้ว

      Funny thing is the oil filter was an option

    • @asiasmaster
      @asiasmaster 4 ปีที่แล้ว

      I use STP on my 67 firebird

    • @byler390
      @byler390 2 ปีที่แล้ว +1

      Wix and K&N are good filters

    • @earth7551
      @earth7551 7 หลายเดือนก่อน

      ​@@byler390no bosch is the best

  • @yukkosuomenen7
    @yukkosuomenen7 2 ปีที่แล้ว

    Did the same, looks pretty nice, but smell not good for about week when drove in city.

    • @PetesGarage
      @PetesGarage  2 ปีที่แล้ว

      Yeah, it takes awhile to bake off

  • @Q8motorclassic
    @Q8motorclassic 2 ปีที่แล้ว +2

    Tried it yesterday. Its start peeling in some places from the first day. Really disappointed so much

    • @PetesGarage
      @PetesGarage  2 ปีที่แล้ว +1

      You must not have had the surface prepared properly or exposed it to too much heat. I've never had a problem

  • @neodiy
    @neodiy 3 ปีที่แล้ว

    nice ...excellente!!

  • @johnhayes309
    @johnhayes309 2 ปีที่แล้ว

    Thanks for the share

    • @PetesGarage
      @PetesGarage  2 ปีที่แล้ว

      Thanks for watching!

  • @josecavada3830
    @josecavada3830 8 หลายเดือนก่อน

    👍

  • @zash008
    @zash008 4 ปีที่แล้ว +1

    Well, i bet the VHT paint still looked good after only 20 minutes also...

    • @PetesGarage
      @PetesGarage  4 ปีที่แล้ว +7

      The Eastwood paint still looks great 2 years later

  • @4speed3pedals
    @4speed3pedals 2 ปีที่แล้ว

    I would use KBS products before considering anything Eastwood offers. Eastwood is just another Chineseum outlet.

    • @PetesGarage
      @PetesGarage  2 ปีที่แล้ว

      The products I use are pretty good

    • @4speed3pedals
      @4speed3pedals 2 ปีที่แล้ว

      @@PetesGarage I have the reverse situation and Eastwood was a POS with any help. I do not reccomend their products as everything they sell is available elsewhere with better service.