@@carphotography yes i just seen the video great work and yes 3d printing is quit addictive, thing is i have learnt so much from printing and lasers ,i enjoyed designing and making my own stuff .You sir have helped me with tons of things on the laser, im now doing photos on wood and canvas .
Great work. I am just learning and playing with my new V400. Building an enclosure now. I too use the PC to control it via Wi-Fi IP. Your video helped my to understand that Cura assist with photos. The puzzle I have in my head is that Cura accommodates timelapse head positions to pause elsewhere long enough to take the pic. BUT.... what tells the camera to snap the pic? I am missing that part? I will purchase that same camera as you have and just need to know how far back from the plate I need to mount it? Thanks again, my new best subscribe friend!
the setting in cura you are telling the G-code before every layer "Timelapse_take_frame" that is being sent to the printer and it is taking a frame, i did just post a video on bedmesh where unless you add a line into your g-code it is not reading the bedmesh. quite important if you havent.
What interface are you on for most of this video? Are you plugged directly into the 3D printer to use that interface? (the one this video begins with) Thanks!
if you connect your printer to wifi and then you can use your PC to control it wirelessly by using the same IP as is on your speeder pad, if you dont get what i mean let me know and i make a setup video :D
on the speeder pad it should show you an IP address, if you type that IP into any device in the address bar it should pop up if it is connected to the same wifi.
@@carphotography I am going to try again, because I did it with two different angles and it was the same result. I am going to try to adapt it as you say, thank you very much
sometimes on mine if the connection is bad it wont show the timelapse, check the connection between your computer and the printer and make sure you download moonraker.
@@carphotographydid you have to do anything to activate Timelapse? Or did it show up in the web interface by default. Mine is not showing up. I am using the same webcam as you and the webcam feed does work for me.
Hi, I do have V400 but the quality of timelapse is not that great as you have. I am curious to see how you have done this, i mean lighting, camera, and other setting. That will give me sound sleep as I am trying to figure out since long time. Thank you
@@carphotography Thank you for quick reply. I haven't expected that quick. I am using Lenovo 300 FHD Webcam with Full Stereo Dual Built-in mics | FHD 1080P 2.1 Megapixel but it looks like this webcam is not good for crispy quality. by the way which lighting you are using? does your webcam allow you to adjust ISO?
@@KM3DPrints no i cant control the ISO it is AUTO but the more light the less it needs to add, i use a Yongnuo 300-IIIW LED light just because that is what i had now i have a 40w 4 foot strip light, it is shown in one of my videos
This was on the original software i dont know if they changed something but you see this worked for me and still does to this day but i never upgraded my software.
![[TH] VCT Pacific Stage 2 - Week 1 Day 2 // GEN vs T1 | PRX vs TLN](http://i.ytimg.com/vi/ZkFjjJNwzH0/mqdefault.jpg)
thank you very much! such a short guide but very informative and saved me a lot of time!
I am new to 3d and bought this same printer.
Nicely done here. Thank you for taking the time to share.
For someone to have a printer in such a short time you have done a fantastic job ,well done
Thank you :D i cant stop looking for things to print out lol its addictive :D
@@carphotography try printing a hinge
@@David-ws6zr i did and i just made a video with it :D as i was making laser cut boxes for filament storage. :D
@@carphotography yes i just seen the video great work and yes 3d printing is quit addictive, thing is i have learnt so much from printing and lasers ,i enjoyed designing and making my own stuff .You sir have helped me with tons of things on the laser, im now doing photos on wood and canvas .
Great input for me - thanks a lot!
Very Well Done !!!
Thanks a lot! thanks for watching
Cool, now let the fun begin
indeed :D i have been quite impressed so far :D
Great work. I am just learning and playing with my new V400. Building an enclosure now.
I too use the PC to control it via Wi-Fi IP. Your video helped my to understand that Cura assist with photos.
The puzzle I have in my head is that Cura accommodates timelapse head positions to pause elsewhere long enough to take the pic. BUT.... what tells the camera to snap the pic? I am missing that part?
I will purchase that same camera as you have and just need to know how far back from the plate I need to mount it?
Thanks again, my new best subscribe friend!
the setting in cura you are telling the G-code before every layer "Timelapse_take_frame" that is being sent to the printer and it is taking a frame, i did just post a video on bedmesh where unless you add a line into your g-code it is not reading the bedmesh. quite important if you havent.
Hmmm... what about setting it up in Prusa or Orca slicer? Cheers.
What interface are you on for most of this video? Are you plugged directly into the 3D printer to use that interface? (the one this video begins with) Thanks!
if you connect your printer to wifi and then you can use your PC to control it wirelessly by using the same IP as is on your speeder pad, if you dont get what i mean let me know and i make a setup video :D
Hi, another great video. I have a problem in that I do not have an interface window. Is it because I have the stock firmware?
on the speeder pad it should show you an IP address, if you type that IP into any device in the address bar it should pop up if it is connected to the same wifi.
How are printing directly from CURA?. Like upload direcly on the slicer screen bottom roght? . Thanks in advance.
Mayba a future video idea?.
there is a cura addon called moonraker install that add your IP address from your printer wifi to it
How do you adjust the focus I have the same camera, but it focuses initially but as it passes printing it blurs the print?
i havent found a way just point it to where the model will be and as the model builds it will get focus
@@carphotography I am going to try again, because I did it with two different angles and it was the same result. I am going to try to adapt it as you say, thank you very much
I have fallowed everything and for some reason timelaps isint recording, what am I doing wrong?
what camera are you using ?
@@carphotography EMEET C960
Why do I not have timelapse on my Interface settings using FLSun V400
sometimes on mine if the connection is bad it wont show the timelapse, check the connection between your computer and the printer and make sure you download moonraker.
@@carphotographydid you have to do anything to activate Timelapse? Or did it show up in the web interface by default. Mine is not showing up. I am using the same webcam as you and the webcam feed does work for me.
Hi, I do have V400 but the quality of timelapse is not that great as you have. I am curious to see how you have done this, i mean lighting, camera, and other setting. That will give me sound sleep as I am trying to figure out since long time. Thank you
yes i added an extra light it allows the camera to use a lower ISO and gives a better quality photo. thanks
@@carphotography Thank you for quick reply. I haven't expected that quick. I am using Lenovo 300 FHD Webcam with Full Stereo Dual Built-in mics | FHD 1080P 2.1 Megapixel but it looks like this webcam is not good for crispy quality. by the way which lighting you are using? does your webcam allow you to adjust ISO?
@@KM3DPrints no i cant control the ISO it is AUTO but the more light the less it needs to add, i use a Yongnuo 300-IIIW LED light just because that is what i had now i have a 40w 4 foot strip light, it is shown in one of my videos
@@carphotography Thank you Sir.
hello, how browse are you suing as google are just blocking the website from using my Webcam as it's not https, cheers
the logitech C920s HD was just plug and play, i dont quite understand your question, can you rephrase it please,
Followed everything here including every setting, got nothing !
V400
This was on the original software i dont know if they changed something but you see this worked for me and still does to this day but i never upgraded my software.
Original software implies 1.2 vanilla, so yeah you're literally doing your users a disservice but okay..