Vauxhall Vectra 1.9CDTI DPF removal programming remap. Bosch EDC16C39.
ฝัง
- เผยแพร่เมื่อ 7 ต.ค. 2024
- Consider to support my channel and all the hard work put into it at / lmautorepairs
Thank you
Hi
In this video I will take you step by step on how to remove the DPF maps from a Vectra 1.9CDTI.
In this case the ECU was a Bosch EDC16C39, the procedure although is similar to other ECUs.
NOTE:
This is a risky process, and it is easy to brick/damage the ecu beyond repair.
Always ensure you are confident of what you are doing before attempt to read or write an ECU, whether that is through the OBD port or on the bench through the BDM port...
Hope you enjoy the video.
Any questions or comments put them below.
Like always, thank you for watching!
![[LIVE] : ONE ลุมพินี 82 วันนี้!! คู่เอก | ยอดไอคิว vs อับดัลลาห์](http://i.ytimg.com/vi/hSsyTl_9bqs/mqdefault.jpg)
hi.
3 years gone and couldn't find winols checksum calculation video. maybe when you get the time..
thank you for all very informative videos
Thanks Leo for the Nice job you do helping us to learn, I have a question what if the reading or the flashing go bad what will happen and how you fix it?
Great video! Please do make a video about checksum calculation in winols and if you can make a video about how to find or recognize other maps in winols it could be very helpful. Best of luck!!
Armands Ločmelis
Hi
Thank you for watching! I will consider recording that then...
Hi there thanks for the great video, regards to removing the dpf and reprogramming, does the dpf temp sensor and pressure sensor still need to be connected?
Thanks alot
Just used MPPS and Volta to map out the EGR on my 1.9 cdti, but it hasn’t had any effect !. Still got the lights on the dash !.
Hi! Yes really interested in checksums calculation! Thank for your's video, the best
andrej hudja
Thank you for watching! I will consider recording that one...
Nice video bro.But I have a question,what about the consumption after the delete dpf?
Should not make a difference...
Thank you for watching and for your comment!
Very great job mate! Please show us how to calculate checksums
Gytis Kozinas
Hi
I will try... have been really busy lately...
Thank you for watching!
Yes, the procedure for checksum calculations with winols please 😁
Perfect video thanks for it and I'm interested if you can to make a video for checksum on winols
Thanks!
For watching and for your comment!
👍👍👍
Hello i have a bmw e92 320d i want to dpf off so i have to buy a Mpps v21 ?? and only the Programms Vault mpps read my Code vault Mapping the dpf and than mpps set the new file on My car so my question is Must i buy somthing else thank you for the Video sir its perfekt 👌🏻
when i check id on my my ecu both edc16c9 and edc16c39 are correct is that even possible?
Still using Windows XP in 2017... i love XP and windows 7
We are in 2021 now... and I still using winXP in a lot of laptops...😉
Thank you for watching!
thanks for this video, do you know which software to use for delphi hsfi 2.1ecu used in zafira 2004 model, thanks you very much
Great video did you use a original mpps or clone ? I also raise my hand for the checksum.
hicham bouchou
Thank you for watching!
Clone...
Hi friend yes can you make a video for checksum calculation?
Hi, what version mpps did you use, and where did you buy it from, thanks
i think it will be informative to do the calculate the checksum good job as always
sadik mamoun
Thanks... Will take that in consideration...
I did it! Thanks mate!
One question tho.. I noticed that your computer recognizes the type of file you created, but mine doesn't. What program that is wich creates a picto for the file on your laptop?
Volta...
Thank you for watching and for your comment!
Thanks very much for your videos.
Mpps is good as kess By calculations or not?
Like kess, calculates some...
Thank you for watching!
Hello,please tell me: do you have to do dpf ash reset before writing ? i have ford sid206,dpf off is done already but somehow it is wrong,i did it now by myself. do i need to do dpf ash reset now before writing the file? p.s. i too have mpps. thanks mate
Depends on the ecu...
But I usually always get everything reset first...
If that still not solve it, you might have missed something while modifying the file...
Thank you for watching!
Hi, great video! Will this method stop the car from trying to regenerate or does it just keep the engine management lights off,
Thanks in advance
Hi
It will stop regenerations....
The car will behave as if the DPF was never fitted in first place...
Thank you for watching and for your comment!
you have to take the DPF off and eather drill it out or stick a straight through pipe on it.
@@thesamsungexperiance8853
Correct....
👍
Great job watching you for a long time now.. Please do a video on checksum calculation with winols.. Thank you
Hi
Thank you for for that...
I will at some point...
Does it turn regeneration off? I've heard that that those engines regenerate after 800 km even though you've deleted dpf.
Regen it turned off at the same time...
Hi can I use volta also for egr off?, BTW very good tutorial, thank you for your effort.
For some... yes...
Thank you for watching and for your comment!
@@LMAutoRepairs It is Saab 1.9Tid with edc16
Hello have the problem with MPPS that I have 3 different ECU versions for my vehicle how do I know which is the right one?
Hello very good video. I already remap the ECU but now I can't start engine. How I can rest the ECU? Thanks
Hi
Does the tool you are using, corrects the chk sums?
Most likely is the reason...
If there is a problem with the flash (maps), reset the ecu will not resolve the issue...
Thank you for watching and for your comment!
Hi Do you known how to identify if ecu is EDC16C9 or EDC16C39
Usually through the part number... if not stamped on the ecu label...
👍👍👍
Great video, thanks! I will ask, why volta and no ecusafe 2.0 ? I see close of volta you have ecusafe, it is beter software on dpf off volta then ecusafe?
Melissa Haughney
Hi
Thank you for watching and for your comment!
When you have two things that give you the same outcome, there is not really a reason why you choose one or the other...
So, what I am saying is, that the same way I went for Volta, I could have gone for ECU safe.... lol
lmsvvavr Hello, I have another question if you can help me for a better direction? Can this method will work if i swap only ecu edc15 or edc16 by read and write data, sure ecu with same hardware (number). I ask because of immo will this method work? I am more confident through obd port then on bench and i think through obd look a clean work. Thanks again
Melissa Haughney
Well, immo is slightly different...
On the video we read and write the flash memory, immo is in the eeprom...
So, you can do it through OBD, but you need a tool capable of reading the eeprom through the OBD...
On Vauxhall, best is get the pin codes, reset and reprogram...
Or, on the bench, copying the eeprom data...
Hope that helps!
lmsvvavr thank you!
Hello!
All the congratulations for your work!
Can all these read and write programs be programmed via winols?
And what is a price of winols software?
Thank you man..
12V Bar
Winols does have an option to read and write, but not sure which interface you connect with it... as I use other stuff for that...
As for the winols price, check the link below...
www.dyno-chiptuningfiles.com/winols-reseller/winols-software/
Thank you for watching!
What is the difference?
What are the checksum points? What do you have winols?
I currently have the k-tag clone red. I would have bought some more cloned devices and software just to be able to handle these things. DPF, EGR, IMMO off ...
Thank you man.
great video mate are you able to delete the egr valve on a mk3 mondeo tdci
Paul Mayou
Hi
Possibly... never done it though....
Hey there,
What software are you using?
Will it work on Saab?
Thanks
This is MPPS...
Is all depends on the ecu fitted on the car...
Thank you for watching!
So i managed to get a MPPS V16 Clone and Volta Software. But im a bit scared that the MPPS will brick my ECU? Did heard a few horror stories. My ECU is remapped before, im planning to buy a used ECU, read the remapped maps from my original ECU and just put it on the second one and modify it EGRoff DPFoff with Volta? I would do a EGRoff DPFoff at the place where i did the remap but they refused to do it. They had some legal problems before after they selled DPF/EGR Off Software ..
I have OPCOM/Vauxcom and a GM MDI Clone (VXDIAG) so programming the Immo is not a problem for me.
Car is a Vectra Z19DTH EDC16C9 (if i remember right, i think i dont have a C39 but i need to check witch one).
Hi
There is always some risk involved...
Make sure you use a battery maintainer...
Yes, if the ECUs are same, you should be ok in read from one, and put it on the other one...
@@LMAutoRepairs i mean i thought to read my ecu, sent the bin file to a remapper and pay for it .. and they promise they wont touch the DTC Table as much as ecusafe or volta. But you never know if its true.
Im new to this WINols and decoding stuff. First ive got a stock ecu file from a EDC16C9 and i managed to finde the EGR map and the right hypersis which you need to zero as did Volta. But Volta did also changed some other stuff which i dont know what these thinks are. I think it deleted some DTCs?
i mean when i manage to get another ECU i can play with this stuff. Prepare a File with Volta and try to mod my bin file myself looking at the Volta File.
Thank you for your reply :) do you have like a "tip jar" :D ?
@@THExPsyGamerx
Check my TH-cam page... links in there...
Looks like you have a plan...😉
👍👍👍
hey i got a zafira b 1.9 cdti with the bosch edc16c9 and i would like help to remove the dpf and egr
i read the ecu with mpps v18
Hi Opel zafira b 1.9 cdti 100cv is ok
Hello. Is it certain that the file read mpps is enough to dpf off? I must do it in Opel Vectra 1.9Cdti 2008. Edc 16c39.
On OP COM it shows ECU as EDC 16C. Any ideea what type? 16C9? 16C39? Where can i find this info? Car is Astra H 2005 1.9cdti 150CP. Thanks
The ecu part number... Google it...
Thank you for watching and for your comment!
@@LMAutoRepairs thank you for your quick response. Seems like it is 16C9. Will MPPS read and write the file the same way as for 16C39?
@@cristianiacob6579
Pretty sure it does...
Hello bud :) Well done. Please do make a video about checksum calculation.
Daniel Zmora
Thanks... Will do...
Hello.. i used mpps to delete egr. All good.
However ive used kess v2 stage 1 remap and got a write error.
Now ecu is blank car wont start. Do you know how to recover ecu. Or i screwed .. thanks man
If kess is still connecting, try again...
If not, try recovery mode is available on that ecu...
If not available, open the ecu and try with K-tag... all of that failed, yes, I guess another ecu is the way to go...
👍👍
@@LMAutoRepairs thank you for reply. my mpps stopped working after a few turns..So i tryd kess and now have a bricked car :(.. recovery mode gets 100% then says write error. looks like a new ecu and locksmith
@@LMAutoRepairs sorted it i downloaded a fresh bdm dumped file. and it flashed 100%
kess needs a full read not patial from mpps.. unbricked car runs sweet.
Good to know...
Well done!
👍👍👍
Hi lmsvvavr, i just want to ask you, should you remove the sensors for DPF after done the file with volta? I just remove one dpf with DPF Remover on EDC16C39, but 2 times already have fault codes related with dpf. This soft removed very well EGR, but with dpf have problem in my opinion. If i remove it with volta should be OK? Or just to delete every fault related with DPF? Thank you in advance
Georgi Altanov
Hi
In the case of this ECU, I left everything connected...
Ok mate, thanks anyway
It will delete all dtc codes. Not only those related with DPF. Volta and ecusafe solutions :)
I have a few questions. If I remove DPF should I remove DTC's with another software? The other question is if I remove DPF should I any sensor connector remove as well?
Hi
It varies from car to car... some you leave everything connected, some you need to disconnect certain sensors... some you need to clear codes before the removal, some after...
Each case can be slightly different...
Thank you for watching!
@@LMAutoRepairs Thanks for answer. Your channel is awesome. Is there a program that helps you in these things?
@@martonhorvath1887
Thanks...
Kind of, there is some out there, you will find them with a quick Google search...😉
@@LMAutoRepairs Can I get a private contact? For example an E-mail adress? I don't find it. I'm not english so I don't speak it well. Thanks for all the answers
Nice work 👍
Do you know of any software to virginise continental Ecu sid206?
Shane Mcdonnell
Thank you...
I think I never had to do that one...
No problem thank you for your reply. I have second hand ecu to sync to immobiliser original ecu is non existent..
Hello, your channel is great! Very good content. I wonder if you can help me, I replaced injectors on z19dth 150bhp and used opcom to enter calibration codes but now I have tapping relevant to diesel knock before boost. It is driving me insane .. please advise me what I can do
Virulent
Hi
Thank you for watching!
Ok, first were the injectors new or used?
Just wondering if they were used, are you sure they were all in good conditions?
Silly I know, but have to ask...
Also, have you checked that the calibration factors have correctly accepted by the ECU?
What was the initial problem which lead you to replace the injectors?
Live data, have you looked at it?
thankyou kindly for your reply!
The injectors were used unfortunately.. but i purchased four injectors and replaced only two.
i have tried the remaining two and still have the same issue.. surely all four injectors cant be bad? the ticking stayed the same whatever injector i tried..
The reason i changed two injectors was because cylinder one and cylinder two were not functioning correctly in the deviation data. Cylinder one was -5mg/stroke and cylinder two was +5mg / stroke. i believe only injector two was the faulty one however..
The symptoms i was having was during driving the vehicle, on hard acceleration it sounded like the injectors jammed and clicked very loud intermittently.. and a puff of white smoke out of the back, then resumed normal driving. this gradually was getting worse as time went by. it only did it every 50 miles or so! also there was abnormal engine judder between 1000rpm and 1800rpm.
the new injectors have cured the misfire issue and the judder. the vehicle runs spot on however i am left with the audible ticking which sounds like diesel knock. i was wondering if it is possible that the new injectors are functioning correctly and i have an issue with cylinder 3 and 4 now? because 1+2 were functioning incorrectly before it masked the problem with the other two cylinders. its driving me crazy. i dont want to go spending money on refurbished injectors unless i am sure that thats the issue.
the only other suspect is that i have a broken rocker arm. as discussed by somebody i know. i have extensive mechanical knowledge and the vehicle is running too good for it to be that. it would run rough and it just doesnt.
i really appreciate your help sir.
Virulent
Ok... makes perfect sense...
Two things, have you checked live data after the injectors being replaced?
Another thing, have you checked that the correct injector codes have been stored in the ecu?
lmsvvavr yes I have looked at live data, all deviations are within +/- 1mg/stroke
I have stored the new codes and cycled the ignition several times and re-read the codes and they have saved.
I inputted the codes using Chinese opcom, will this be an issue?
Thank you
Virulent
Shouldn't be... that's why I asked if the correct coded are actually in the ecu...
I had in the past were the procedure went successfully, but when looking again, the old codes would come up...
You are not getting that...
Have you checked cylinder compression?
I know... but it might work checking it...
Another thing is, is the high pressure regulation ok? No spikes or deeps?
hello mate great work
please Explain how to fixe checksum with winols thank you
Hi
Thank you!
I will try...
thank you mate i'm watching all your video
bravooooooo
zayn aoun
Much appreciated!
Hope you stay tuned for the future ones....
Hi thank for quick answer. I have Vauxhall Astra h 1.9cdti 150hp. I use MPPS 13 cable. First I check with Delphi tool what is my ECU code. There show me EDC16C9. After that I read ( with MPPS 13) ECU fail from car and marking EDC16C9. After download file from ECU and car it is won't start engine. Can you help? Thanks
Ok, so see if I got it right...
You read the ecu...
Then you wrote back into the ecu...
And after that the car fails to start...
Is that correct?
Yes thats correct
I tried writing a map to my car today but just after it started the program terminated and now my ecu is stuck in 'write only' mode but when I try to upload the stock file it fails. Any help please
Hi
You are doing it through OBD right?
What tool are you using?
Thank you for watching!
@@LMAutoRepairs hi,
Yep it was all through the obd but I think the software doesn't work properly with windows 10.
Its mpps clone. Would you like me to email you?
Thanks
Ethan
@@ethanmccrory1727
There is nothing I can do...
Your next option is probably on the bench...
Or kess in recovery mode if available...
Hi can the same method be used on the corsa d 1.3 magneti marelli ?
Hi
Yes...
Thank you for watching and for your comment!
Thanks for sharing! The question: at the beginning of the video you created a copy of car's brainz with numbers name. But then you modified another file that was on your computer and not the original copyied from the car. Why?
MrBorntoroll
Hi
You have skipped the video then... lol
I have explained that at the start I have saved the file with the name that Mpps attributed to the file... when on the server I have renamed the file so is easier to identify...
Hope that answer your question...
Thank you for watching...
What is the best OPCOM tool and Mpps softwere version
Hiii.
Can I use ktag to remove dpf on this vehicle.
Thanks
Most likely yes...
Thank you for watching and for your comment!
👍👍👍
But catalytic convertor is still on or it was removed also?
THE STIG
Catalytic stayed...
Thank you for watching!
Great job!
Thanks!
👍👍👍
Hello, could you tell me witch version of MPPS did you use?
Hi
13 if i recall correctly...
Thank you for watching!
What's the life span of dpf filter,?just bought new van with dpf on it,cheers,
John Easton
Hi
It all depends on the driving conditions...
I have seen them failing at as early as 40k... in the other hand, I have seen them with over 120k and still going....
@@LMAutoRepairs mine has 250k km
@@moxadrian
👍
please do video fro calcu the check sum
Magid
Hi
Thank you for watching!
I think I will be doing that... stay tuned...
always waiting for the next video
Hello, when I plug my MPPS v16 in my saab 9-3 1.9tid it says i got 29volt down in the corner and when I try to read it gets to 1% and then I get an error telling me to get the logs and send them to someone... what would you try to do in my case? I got it installed in virtualbox win xp.
Using virtual machines for something like that, is asking for trouble...
Thank you for watching and for your comment!
hello where can i buy the mpps? do you recommend any link from ebay or aliexpress?
estava a olhar para os icones e reparei que estavam em português!!! queria começar com as repros em centralinas e estou indeciso entre a kess e o mpps! qual recomendas em clone?
Start with kess...
Mpps is not expansive anyway... you might can get both...😉
You can get them from here:
Cardiagtool.co.uk
(Buy them at you own risk, I have no affiliations with this seller. )
Thank you for watching and for your comment!
hi luis.MPPS V16 or V18?
16...
Thank you for watching!
I am looking a way to learn About ECU Re programing. Basically I am looking for a teacher who teach me online. Because I am for away from any school or college where I could learn. So I need help on line. Plz can you teach me some thing?
Hi friend i have Chevy Captiva Which Old ECM Burned due to alternator overcharge so i swapped my ecu .Now my ecu Showing P268A (INJECTOR not Calibrated or Coded) So If I sent you the file of ECU which is taken by KTAG so can you code the Injectors on it ECU Type (EDC16C39) and it's throttle also stuck on 94.9% I recently flashed another file to check any movement happens in throttle position yes I movement happened it comes on 54.9 % so I think may be problem in ecu file could u program for me I am from India .
If I removed dpf for delete and didn't map it what would happen
Most likely the engine light would come on, and the car would go into limp mode...
Thank you for watching and for your comment!
@@LMAutoRepairs how much is it to get it mapped out
Can a remap egr (turn off) with mpps v16 in opel zafira b z19dt
Possibly...
If the ecu is supported...
Thank you for watching!
Great video, thanks.
Mambre Khachatryan
Thank you for watching!
Hi
I have to dpf delete on audi 2l engine a3
Can I read and write it back or I need to modify the file
Thanks in advance
gino p Alias
Hi
If you read and write the same file back, you are not removing anything, are you?
The maps for the DPF need to be removed from the file, prior to flash it back into the ECU...
Hope that helps.
Thank you for watching...
LM Auto Repairs
Can I send the file to you can u remove dpf?
I DL some VOLTA ,but there is code for the winrar , can anybody help ?
I always thought this was BDM only as OBD Didn’t read all the banks of data?
Hi
Worked perfectly on this one...😉
Thank you for watching!
can you please tell me the names of the sofwares you used
which program can I use to read EDC16C9, kess and ktag doesnt have read option for this ECU. Carprog also not
Which car and engine?
@@LMAutoRepairs Opel zafira 1.9 Z19DTH
@@micseulk5731
K-tag can do it... just checked...
@@LMAutoRepairs oke thx, I wil try again. I have clone not original
@@micseulk5731
Same here...
Love your videos.... but you never did do the winols checksum guide ;-)
winols checksum is very simple, you just load file and software tells you if chks need correcting, once corrected export file and write with tool, ecm titanium also good for editing and correcting checks.
cheers dude rely helpful
holly may
Thank you for watching!
What´s the software for ecu edition opel?
Already answered...
Yes off course, volta sensor decoding. to modify the engine maps that can be upgraded in opel 1.9cdti 120cv edc16c39?
I use vagedcsuite in audi but in opel I don't know. i dont like winnols
I would also like to see winols video👍
Hi nice video!
Global Car Parts
Thank you!
iv heard that most of these dpf removal companies they guarantee that it can pass mot whats your experience
So far so good...
Thank you for watching and for your comment!
@@LMAutoRepairs not sure whether to replace with a new oem dpf, im having p2453 issues sensor is fine but after regen oil change still service engine message and soot filter full
messages and limp mode. i think volvo say 75k for consumable replacement of the dpf.. just a pain tbh to get to the next solution.
@@7302ab
If everything else is fine with the car, I would replace it... and you would be ok for another few years...
I have had two cars with DPF removals PASS at various garages, i.e. they still look like they are there. What is interesting though is that my car got an advisory for "emissions too clean!" without the DPF, and the emissions where 0.13 for a 0.50 rated car. Crazy! But yes it will PASS. The whole DPF is a stupid idea, they strangle the engine and cover people in sut when you accelerate hard, and to clear them you have to drive at 90mph in 2nd gear for 4 hours. Ohh and i'd like to add, I have a 1.9 CDTI Zafira and the fuel economy at 70MPH is 62MPG, If I drive like the manager of a mattress company I can achieve in the 70's MPG. Fuel economy vastly increases and the extra power from a remap can see a lot of high end cars off! My Zafira is in line with a Ford ST.
Hello I am trying to remap my vectra 1.9cdti using the same mpps software as u I can id the ecu and take a copy of the ecu data I have a saved remap file on my laptop when I try and write the map to my ecu it says error
Can I remove the egr and swirl the same way ? And have you got a link for cable and software
Hello kess v2 will also read this driver or just mpps?
ewelina1946 msp
I do not have kess 2... but it is possible that kess can do it... there is other tools out there capable of that...
Thank you for watching!
Kess V2 is read this ecu like a charm, just like MPPS. You can do it.(was write I by mistake)
Georgi Altanov
Thank you for sharing!
hi i have a question what version have you mpps? Regards
ewelina1946 msp
I have v13 and v16...
Nice. Gj.
Artur Modrzejewski
Thank you for watching!
hello,i want to make checksum correction , when i tried to do it with winols 2.24, it shows this message
"error while handling the file selection,the operation was cancelled", this error is when i want to save the file, please any help
thanks
zayn aoun
Hi
Which ecu are we talking about?
Is your winols only doing that with that file?
Hi man ,i tried to change all(file ,the software to make dpf ,........),already same problem ,the error message come when i try to save the file
thanks for your help
Hi winols do that with any file , already same problem
zayn aoun
It might be your winols then... try to reinstall it...
Hi friend ,thanks a lot ,evreything is ok ,i changed my operating system
Where is egr off software?
JORA MOTORSPORT TEAM
Hi
What do you mean?
In the ecu, or a software to work with the map to delete the EGR map?
Thank you for watching!
That's illegal
A lot of things are ilegal...
😉
So was the government telling us to buy dirty diesels when they knew full well they were dirty!
184000 on the clock tho... bet it runs like a donkey
Can't remember now... lol
Thank you for watching and for your comment!
Hello LM Auto repairs...Thanks for all the info from your videos great work that you are doing.. I need to ask if you a have a phone number that I can contact you.. .Hope to hear from you soon . Thanks.
Hi
What exactly are you looking for?
As you can imagine, I am not gona share my number here... but I am happy to help... if I can!
Thank you for watching and for your comment!
@@LMAutoRepairs Hi. I understand that..I have some things to ask you ...can't talk here...Do you have a email or something where we can share info more private?...
@@danielalex9606
Send it to lmsvvavr@sapo.pt
But make sure you put a subject on it... as I will have to search for the mail... as I don't use this account often due to spam etc....
@@LMAutoRepairs . Sent. You can check pls.
volta solution is rubbish for this ecu ;)
Mircea Florea
I have done a few of this with Volta... so far so good...
Thank you for watching and for your comment!
He's right. Try to diagnose this car later and poof - no dtc's :) It deletes them all.
c ' est bougies de préchauffages , ..
Hi
La lumière de bougies de préchauffage n'est pas seulement pour ce système, il peut également signifier un type ou un défaut électrique, dans ce cas était à faire avec les capteurs DPF manquants.
J'espère que cela pourra aider.
ok , mais dans la plupart du temps , à 90/pour cents ce signe signifie bougies de préchauffages , mais vous avez raison , il peut avoir des défauts , et ils en na , mais sinon , merci pour ta vidéo , je vous remercie .
Pas de problème...
Merci d'avoir regardé!