52mm warm up ride after tune-up.34f and breezy.
ฝัง
- เผยแพร่เมื่อ 18 ก.ย. 2024
- After the bike sat in below 0-f for a couple days,and rain the rest of a week, I decided to do a complete tune-up check.The magnet was touching 1 side of the coil pick-up as 1 side gets closer as it rotates. I removed the entire coil cleaned it, and adjusted with cardboard gap tools ;) Plug gapped @.030 .Fuel is 93 oct.Semi-synthetic oil mixed at 20:1 as it's still breaking in.
I cleaned the carb after draining the fuel tank and removed the old filter.
I used a new piece of fuel line to blow through all ports, adapters. This is a 2 mile ride in 33-34f temperatures. It did hit 21mph for a moment accidently near the end. :)
Sorry for the abrupt end, I was looking to see it was still recording.Irony...
![เขามัทรี - เอ็กซ์ ศุภกฤต - จอนนี่มิวสิค [ Official MV ]](http://i.ytimg.com/vi/AS9ufKuQIVs/mqdefault.jpg)
Cold but very mellow. Thanks for the ride.
Thanks Leo.I was chilled but am used to it.The bike should do better once broken in,but I won't push it yet. Trails are too muddy anyway ;)
Thanks for the ride along brother I enjoyed it and your right 2 strokes don't like the cold ride safe brother
Really nice looking neighborhood to take a ride in. Thanks for the ride my dude 😎
TY.
E gad, 35 degrees! Ride safe Brother!
Just a tad nipply,but worth it.
Hey thanks for sharing. Nice seat set up. Cool lights. Looks cold in your area. Where you at ? . Don't know how I wasn't subscribed to your channel. Great video great neighborhood for a motorized bicycle. Your video reminded me of when I use to ride my motorized bicycles all around my old neighborhood. City of Lynchburg va. Sadly I moved to mayodan nc nowhere Ville. I over complicated the purpose of a motorized bicycle yrs ago. Sure wish I watched this video about 7 yrs ago. I would have kept things simple.
TY.I'm in the middle of Michigan. It's not a big town as I can ride about 10 mins in any direction and be out of it.I've seen a few other motorized bikes during summer, but more are going electric. I do get allot of questions about the bike,and am hoping more build 1 to enjoy.
Thanks for the ride bro
Thnx for checking it out.
Very chill, kinda zoned out and just vibing there at the end love it. I'm amazed how well that runs on stock carb you have the best sounding 110 on youtube bro!
Thank you.
I can't believe you're riding that with that clamp on screen door roller chain "tensioner". I was almost killed by one of those things. It got pulled into the rear wheel and locked it up solid. I crashed hard. Lots of injuries. But it could have been far worse. I was in a bike lane, with a sidewalk on my right and bumper to bumper speeding traffic on my left. Fortunately I went down to the right, or I would have been run over by several cars and wouldn't be here anymore. I can't believe they are still making those things.
My frame is Oval so it can't twist, but thanks for the warning.I use a gear and not the plastic pulley on the tensioner as it lasts 1000's of miles and keeps the chain lined up to the sproket.I had a 'spring tensiner' and it allowed the chain to bounce on rough surfaces and jammed causing me to crash last summer.
Looks like the 56 tooth Sprocket, Thats as Big as I can find without have to modify something but if I want to use my CVT setup on a build I need a Big Ole Sprocket to get close to gearing, Thanks for the ride around 👽👍🏻
Thanks Op. About 5 years ago,when I was looking for my 56T There were 60T available on ebby.
Always ran my old 87 Honda CR-500 two stroke race bikes fuel mixture at
32to1 full synthetic 👍
Thank you.I plan on using that mix after it's broken in.I still have good cross-hatch in the cylinder so I'm taking it easy.I've only let it run up RPM's freely a few times so I don't get a ridge when it's set.
🍿
👌👀👍
Highly modified 👊😎
LoL,thnx. I only cleaned the steel sleeve to match the ports and the Reed valve is the "mod". It only keeps the 'backflow' from the running. I did nothing to make the motor different. The Poo-Pipe is getting removed and the muffler will be 'modded' to flow free. Thanks for watching.
Stack 3 base gaskets Open port exhaust up a little bit and get rid of that junk carburetor it will run a lot better took me a year and a half to get mine running 50 mph
Thanks for your comment. I did take the cylinder off and raised the exhaust 3-ish mm, and the transfer ports about 4mm too as I checked with the head off,no intake or exhaust on and looked closely at where the rings and piston were to each..Have shopped for gaskets but can't find 'head and base' gaskets only