In ignorance there is bliss, he's blissful, but remember it stated he's showing how to repair a part as done in a method he he described, basically he's promoting a repair style he developed. I personally would send him a dozen center drills and spotting drills.
Well, it looks very much like the gear was purposely cut, and then with the grinding, the tooth pitch was ruined as the gear became slightly elliptical..
Wow, what a fantastic fix it always amazes me about the PPE no one where is it and looks like no one actually gets hurt which is a good thing or maybe they don’t talk about it actually everyone is okay
That gear was cut not broken. Worst welder in Pakistan. You can't stick weld forged steel and use it for anything but a door stop. It would fall apart in a few hours of work.
This falls into the category of, can you do it YES; should you do it definitely NOT! I've come to expect better from this channel, cut .the broken one off and make a new one. Sorry guys missed the believablity mark on this one. Looks like a real nice wall hanging. 😊
Ano, vyzera to sice pekne a lesklo, no tvrdost,a pruznost, tepelne spracovanie, modul ozubenia, vsetko je znicene , akurat tak pozerat sa na to, a vcom je ta nova metoda ?😢
WTF is a pitch circle?? I know,, its total BS! Pitch circle my ass. That part will last for ever. I have been in industrial maintenance for 25 years and I have never heard of "PITCH CIRCLE" The pitch of the teeth have not been effected at all!!! These guys do some fabulous work!!
Super jest to odrestaurowane jest jak nowe z pod igły Pozdrawiam serdecznie twórców tego filmu i polecam ten film i kanał każdemu fachowcowi i amatorowi różnej specjalizacji Pozdrawiam jeszcze raz serdecznie. 👍👍👍👍👍👍
Well there you have it, another absolutely disgusting abysmal repair that will fail in 5 minutes. It's not concentric, the span measurement across the teeth is inconsistent and the hardness is now completely messed up from the welding. Throw it away.
Mann kann es einfacher und präziser machen. 😊 mit den Bolzen wird es schwächer. Die Schrauben Löcher sind gute Führung. Einfach ein Ring drehen und zusammen verschrauben. Etwas anschfeißen! Rest ist euch bekannt!
now show us installed and running. There's a difference between can't and won't. There's also no reason for this complete waste of time, given that the "repair" will not work.
What about heat treatment of the teeth? What material is this wheel made of? Do you think the heat affected zone does not change the impact resistance of the material?
Another staged "expertly" made repair of a part that is not shown how quickly the "repair" fell apart. It's funny the channel is named "CNC master" CNC stand for Computer Numerical Control, there's no computers, numerical or any kind of control, lol. And by "new method" they should state "how not to fix..."
These "training" video's get old, fast. Either way, that final result was... no. Those holes were smaller than the original and if this was to be used, the gear could shake itself apart due to being dangerously off balance. The teeth? Meh, I've seen worse.
DO YOU BELIEVE THIS GEAR WILL BREAK LIKE THAT IN NORMAL USE?? IF YOU WANT TO SHOW OFF YOUR SKILLS JUST PUT IT IN REALITY. MACHINING IS BASIC AND EVEN A WOMAN CAN LEARN.
Désolé, à lire votre commentaire, s'approuve que vous ne connaissez rien en conception mécanique, d'abord la pièce a été sciemment coupée pour en faire un sujet. Le fait de nettoyer les axes de cette pièce avec une meule, ne laisse comprendre que ce tourneur n'a aucune notion en mécanique.
Как гласит казахская пословица, по Евраю и тюбетейка. На Аллаха, прости Господи, надейся , а детали в песок не бросай! Спроси у него, он может выжимной графитовый подшипник на токарном станке обработать?
Wow ..how fake is that? It's been cut and broken, and he's destroyed the pitch circle grinding all that metal off. This is last one I shall watch.
they Cut it in half 😂😂😂😂
Циганска работа 😮
It was aligned on the original OD, hardly 'destroyed', did you actually watch?
It's like brand new one. They know what they're doing.
circular economy system, nice strategy to make customer purchase same part again after one month.
I have deep and enduring sympathy for the ways on that poor abused lathe
My thought exactly, I suppose theyr lathes are extremly well serviced, at the rate of overload they îndure..
This is so wrong in so many ways I don’t know where to start!
Start with the first wrong to prove your statement
@@manrhuu I support your point. 😎
Wow, another sprocket cut in half so it can be repaired on video... :(
Yah these people are hard up
@@himtntec нужно прекратить размножаться и не входить в это положение
Strangest 'break/fracture' I've ever seen. Then again, So What.
Generates views = $$$
@@glennkamers 100%
Sure it looks like a new part, shiny, lined up, that looks right. I want to see it on the vehicle working the way it should, but they NEVER show that.
In ignorance there is bliss, he's blissful, but remember it stated he's showing how to repair a part as done in a method he he described, basically he's promoting a repair style he developed. I personally would send him a dozen center drills and spotting drills.
That is way fake right there that is cut on purpose!! 😅😅😅😅😅😅😅
That gear is clearly cut.. Nothing breaks in a perfect straight line.
In Pakistan they do wink wink wink ;)
My thoughts as well.
Very good! This restoration was perfect. These Indians are geniuses, given the few resources they have, seu boiolas!
They are not Indians, they are from Pakistan stoneage.
@@horstmuller7512 Thanks for the information👍
Well, it looks very much like the gear was purposely cut, and then with the grinding, the tooth pitch was ruined as the gear became slightly elliptical..
Wow, what a fantastic fix it always amazes me about the PPE no one where is it and looks like no one actually gets hurt which is a good thing or maybe they don’t talk about it actually everyone is okay
That gear was cut not broken. Worst welder in Pakistan. You can't stick weld forged steel and use it for anything but a door stop. It would fall apart in a few hours of work.
It's not a fantastic repair at all, it's utterly appalling.
I like that Sal the Stockbroker has a new job.
He's the best mechanic in that part of the world. Because of the glasses.
Salu2 cordiales mis hermanos excelente trabajo y muy profesional bendiciones desde Monterrey México y le mando su poderoso like 👍
This falls into the category of, can you do it YES; should you do it definitely NOT! I've come to expect better from this channel, cut .the broken one off and make a new one. Sorry guys missed the believablity mark on this one. Looks like a real nice wall hanging. 😊
Сами режут ломают и сваривают, врядли это ставят в технику, чисто просмотр
показалось)
هذا الكسر مقصود فعلا فهو ليس مكان كسر طبيعى ولاكنهم يلحمون التروس ويصلحون اشياء كثير لا نهم محاصرون لا تصل اليهم قطع غيار وايضا اجور العمال منخفضة جدا
The most crucial part of the workflow is to make a final machining pass to get rid of visibility of dodgy welding beads and disguise the whole scam.
Saljdos desde Ecuador . Soy solfador desde los 13 años tengo 45 años soldando y yo o creo que aguante poco vicel
I'm not determine the cut but very nice the work.
Ano, vyzera to sice pekne a lesklo, no tvrdost,a pruznost, tepelne spracovanie, modul ozubenia, vsetko je znicene , akurat tak pozerat sa na to, a vcom je ta nova metoda ?😢
Vieš, že je to falošné. Strihali to kvôli videu. Je nepravdepodobné, že by sa niekedy použil v zariadení. Predstierajú veľa opráv videa pre youtube.
@@davidnull5590 vela ludi ktori nie su technicky zdatni tomu bohuzial uveria ...
@@davidnull5590 vela ludi ktori nie su technicky zdatni tomu bohuzial uveria ...
If they knew how to anneal it they probably know how to harden it.
WTF is a pitch circle?? I know,, its total BS! Pitch circle my ass. That part will last for ever. I have been in industrial maintenance for 25 years and I have never heard of "PITCH CIRCLE" The pitch of the teeth have not been effected at all!!!
These guys do some fabulous work!!
Ridiculous clean break. But, it’s Pakistan. Maybe from a previous repair.
Keep doing the great job you are a custom to, job well done.
Super jest to odrestaurowane jest jak nowe z pod igły Pozdrawiam serdecznie twórców tego filmu i polecam ten film i kanał każdemu fachowcowi i amatorowi różnej specjalizacji Pozdrawiam jeszcze raz serdecznie. 👍👍👍👍👍👍
It looks like the gear was cut and the repair ruined the tooth pitch with an out of round gear.
What it BEEZ! Dassit, mang!
I'm sure this will be sold again but on the second hand market not for self installation
I wonder where he put the earth clamp when he was tacking it up in the lathe! LOL
The poor bearings!
Alvin and the chipmunks are arguing in the background make more sense
Такое ощущение, что специально разрезают ради видео)
А тебе не кажется, что этот токарь-пекарь на Калугина из уральский пельменей похож?
@@sergejmironov5984 Немного похож, наверное без грима.
Aqui no Brasil🇧🇷 é assim, quebrou...joga fora e compra um Novo...🤗
Yes it’s a good job but the part is not anymore the same.😩
THANKIOUPR❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤
Is this what they call " the land of shoddy". Very similar to some of what the north factories produced during American civil war. An Aussie.
Ажойиб
Well there you have it, another absolutely disgusting abysmal repair that will fail in 5 minutes.
It's not concentric, the span measurement across the teeth is inconsistent and the hardness is now completely messed up from the welding. Throw it away.
Something is not right with this video repair
Subtitled “ how to make an elliptical gear”
Yep, you could see it running out in his Mickey Mouse lathe
The only way we can get this crap off YT is to stop clicking on it.
Down vote
This one 950 to 286👎
Mozilla Firefox extension -Return You Tube Dislike
there's all kinds of crap on YT... I tell people to stop going to NBA games and to stop watching it cause it's a clown show now but people still do
Hola . . . saludos impresionante trabajo . . . 😎👽
Mann kann es einfacher und präziser machen. 😊 mit den Bolzen wird es schwächer. Die Schrauben Löcher sind gute Führung. Einfach ein Ring drehen und zusammen verschrauben. Etwas anschfeißen! Rest ist euch bekannt!
BRAVO !!!
Super el ingenio de los pines. No se varan. Que actitud a la vida tan espectacular. Dios los siga bendiciendo
yo creo q esta bien hecho el trabajo, seguro este engranaje ya no sera para su propósito original sino para chancar platanos😅😅😅😅😊😊😊
Ну да! 😂 сама так сломалась!!!!!
You're perfect. I give you 99.99percent to your work
now show us installed and running.
There's a difference between can't and won't. There's also no reason for this complete waste of time, given that the "repair" will not work.
What about heat treatment of the teeth? What material is this wheel made of? Do you think the heat affected zone does not change the impact resistance of the material?
The hardness is now messed up from the welding heat, but that's only part of the problem, there's plenty more.
See you again in 6 mos sir👍🏻
nice welding!!! but!!! how about balancing and hardening? 😂😂😂 good for playing!! nothing else!
Jealousy is in the air.
بسیار عالی و حرفه ای .
Well done job, congratulations. Greetings from the Netherlands 😊
precisión: +- 10mm!
the diameter of gear will changed
I m mechanics good job
How can anyone think this is a good idea. This is some of the worst machining I've ever seen.
Great machine, that would accelerate jobs with a cnc, cutter table. And post molding foundry.
Nice repair, for the broken bearing.
Looks good but the factory spec are way off it is not long for this world
This one will lose you viewers because it really looks like you cut the gear on purpose and then destroyed the tooth pitch with the repair.
Another staged "expertly" made repair of a part that is not shown how quickly the "repair" fell apart. It's funny the channel is named "CNC master" CNC stand for Computer Numerical Control, there's no computers, numerical or any kind of control, lol. And by "new method" they should state "how not to fix..."
Respekt Meister ❤
Nunca essa engrenagem vai aguentar a preçào do motor com peso
OMG that was painful to watch
Ji Hi Dear Bro Very Very Great Job Ji ❤❤❤❤❤
Well.... that should last a week, maybe two.
Disana sudah musim hujan sepertinya
The break was not a clean break, This definitely not how to repair this piece
Понравилось как сделали эвольвенту зуба шестерни
Good Job by an engineer good repair
Perfeito !!! Parabéns !!!
Main Punjab, India se dekh raha hun. Hamare, idhar repair, Nahin, karte Jahan to naya dalte, Hain, ya, disposal ka. Dalte hai
These "training" video's get old, fast.
Either way, that final result was... no.
Those holes were smaller than the original and if this was to be used, the gear could shake itself apart due to being dangerously off balance.
The teeth? Meh, I've seen worse.
Hi no problem next months come back for all gearbox to fix. In Pakistan part must be expensive. Than mechanic
È tutta una serie di errori ! 🤮👎
What is a bypass mechanic?
При сварке детали зажатой в бабке масса где? За это положен учннср!
Der Strom fliesst über die Kugellager; keine gute Idee!
DO YOU BELIEVE THIS GEAR WILL BREAK LIKE THAT IN NORMAL USE?? IF YOU WANT TO SHOW OFF YOUR SKILLS JUST PUT IT IN REALITY. MACHINING IS BASIC AND EVEN A WOMAN CAN LEARN.
FAKE - Never seen a gear break like that, it has clearly been cut🤣🤣🤣 Not very genuin repairs.
做玩具就可以
完全不能使用
👍👍
cool !!
Можно ли придумать что-то более сельское, скотское и нелепое? Ремонт шестерней вилами и граблями...
Jak zwykle świetna robota Made in Poland Dariusz72
Toutes ses techniques de réparation sont obsolètes.
فلسطين حرة
Palestina libera ! 👍🙏
@@us4747 💖💖💖
У этого токаря золотые руки и голова смотреш на удивлением просто супер такие люди рождаются редко дай Аллах ему крепкого здоровья Казахстан 🇰🇿
Désolé, à lire votre commentaire, s'approuve que vous ne connaissez rien en conception mécanique, d'abord la pièce a été sciemment coupée pour en faire un sujet. Le fait de nettoyer les axes de cette pièce avec une meule, ne laisse comprendre que ce tourneur n'a aucune notion en mécanique.
Как гласит казахская пословица, по Евраю и тюбетейка. На Аллаха, прости Господи, надейся , а детали в песок не бросай! Спроси у него, он может выжимной графитовый подшипник на токарном станке обработать?
@@bfaridbf3029 Дикари С!
Sir ap sy milna chata hun ma
OK it's like a brand new sprocket but reaper also... Nice..
🧿🙏🧿🙏🧿
Hello sir
👍👍👍👍💪💪💪💪👏👏
❤
This video is purely for contain only
Nic ❤❤❤
God job bahut acchi kalakari hai
beaucoup de commentaires méchant, quel triste monde
🎉🎉🎉🎉🎉🎉🎉🎉😮😮😮😮😮
next?
Terrible
🙏🙏🙏🙏🙏🙏🙏
That is in no way a fix
The holes aren't the same size. Will be out of balance. Nice job otherwise.