Primos 1953 Ford F100 can we bring it back to life
ฝัง
- เผยแพร่เมื่อ 26 ธ.ค. 2023
- my brother's 1953 Ford f100 needs some attention and to get back on the road. this awesome truck has been sitting for far to long and needs the fuel system cleaned.
check out our merch, just click the link below to head over to our website. Thank you
howlinwolfgarage.myspreadshop...
venmo.com/u/howlinwolfgarage - ยานยนต์และพาหนะ
![เก่งแต่ลับหลัง (FINSTA) - ส้ม มารี (Zom Marie) Ft. Punch 4EVE [Official Teaser]](http://i.ytimg.com/vi/Fvt0Wz1hfGY/mqdefault.jpg)
Thanks for your time 😊chevy and Holly my best
Old school way to set timing without a timing light. Engine at operating temp, in gear, lock brakes, full throttle against stall. Advance the timing until it just starts to ping. That is the extreme timing setting. Back it off a cat hair and lock it down. On a standard, same procedure but you need to lug the motor in high gear, so there is more back-and-forth.
That is surely worth it. It is one of out favorite trucks.
That’s a sweet looking truck. I think the older cars is better looking than the newer cars
We agree
Coors in one hand carb in the other, my kinda a guy👍👍👍
👍😆
Is there anything you can't do? Your still teaching, keep up the good work.
You are right on about junk in the line. The ethanol gas scours silt and anything else off the inside of the fuel lines. You can chase that forever but the lines need to be replaced stem to stern. Don't forget to check inside the fuelk pump as well as there are nooks and crannies that hold junk that comes loose.
RRRRRRRRamon!!!! My bottom end dropped as soon as I seen that carb tilting😂! Got lucky there!
Hahaha yeah we really did get lucky for sure
Edelbrock for the daily, Holley for the win
Good job hitos. 😅😂😮
Best running Ford Windsor I've owned had the old Motorcraft 4100 on it. That engine hated Holley and Edelbrock.
Yes. More wolf videos. ❤❤
I am all 💯 % Ford man i love the old truck the best
Great old truck. Love the body style even if it is a Ford. Lol
check the vacuum advance to make sure the diaphragm is not leaking if it is rotted and leaking it will idle fine until you put a load on it and will give you that off idle lean out i have experienced this several times especially when they sit for long periods of time cool truck i have a 56 coming out of the ground this summer it will be my 3rd one i have owned and built
Your bro is lovin' a "Mountain Soda" per VGG standards. If you don't know Derek, I'm sure you would get along famously.
My Dad had a ‘53 with original
Flat Head motor when I was a
Kid. It was a great truck. Man would
I love to have that Truck with the
351 and C6. It seems like that one
Needs a tank flush or replacement and
New fuel lines and good filter.,
Great Video Hector, I hope you are having a great holiday.
That is really cool. Thanks for sharing. Yes, we need to clean and replace everything, and we will
The carburetor definitely looks like it had. E85 ran through it.
Love the truck
Wolf 🐺 working on a lot of ford's these days not that I'm counting 😅
😂
I hope you guys do more videos like this I enjoy videos like this. Mechanical stuff I always enjoy.
I hope everyone had a great Christmas
We plan on doing a lot more videos like this. 👍 thanks for watching
Neat!
I mean it's a Ford but still old school Cool. Howlin from Texas. Av gas won't rot
You are absolutely right Hector, today's fuel is junk nearly have to run 110 av lol
Great stuff Sir,
You are making me itch for my own engine swap. I am replacing the 460 for a 351 I found in a salvage yard. Junk yard finds can still be good luck but I have a lot of work ahead. Fortunately this engine has never seen Ethanol fuel. I have friends that cry for the Sniper and HEI but I don't mind setting points and adjusting the carb. Riding my 65 Panhead from home in Montana to Washington DC for Rolling Thunder meant taking three sets of jets/needles and adjusting the float as I dropped elevation. Few people consider elevation change when tuning and running any engine, now you have to watch where you buy fuel? Makes a body miss the good OLD days!
Good luck Gentlemen! With Respect and Love, You are in my prayers
Hoka Hey
That's awesome. You should definitely do the engine swap if that's what you want. 1 hour a day is all it takes. 1 hour a day is 7 hours in a week and can be more on the weekend. So, at the end of the week, you have a full day of progress. Good luck, thanks for watching
It sounds awesome when it’s running 💪🏻👍✌️
One thing may stop that corrosion every 6 months put in a half of QT of ATF it clean the carburetor as you drive my dad did this to his car's do that to a tank of Gas
You might want to change the fuel filter and blow the gas line with a air compressor!
good thing you got that washer out if you watch nicks garage you will see what a little piece of metal can do to a engine it incredible good video keep them coming
Yeah, it can be really bad. We got lucky
I think Rory Irish ran an engine until it broke and when he took heads off there was a bolt stuck into a piston.
@@graememckay9972that was Shawn's buggy that was a trip never seen that
Beautiful truck your very lucky just to work on that Hector
❤
I had a 53 f 100 with a 289 twin four barrel and a Hurst four on the Floor with a five inch drop all the way around .candy apple red
I bet that truck looked amazing. You had me at 4 on the floor..lol
Great video Hector!! Keep 'em coming!!
Thanks for sharing Happy holidays 😀👍🎄
Happy holidays!
👍🏽👍🏽😊😎🙋🏽♂️✌🏽
He's really done alot of up grades on it..a little work and it's back to doing burnouts..I had a 55 called it old blue with a 390 automatic
I like the 390 FE motors. Old school cool!
Old Ford f100
a Falcon (1960?)and a yamaha warrior 3 things on my vehicle bucket list
That falcon, I believe it's a 61, and it runs and drives, but we are going to engine swap that car soon. 302 and a 5 speed with a clutch
@@rockabillychavez awesome can't wait to see some burnouts
The fuel these days is garbage. I've had to clean that crud out a few different carburetors and fuel lines over the last couple years.
It's definitely not what it used to be.
My 51 had that same problem even after cleaning carb and replacing fuel line ended up being the foam in that race tank
Right there, at the end, I clearly saw what the problem was! It's that blue oval with the 4 letters starting with an F in it!!! 🤣😂🤣😂🤣
Maybe the fuel filter, if it even has one.
Nothing against the Windsor but I prefer the 351M I had a 79 Bronco with that and a commercial c5 OHHH BABY
I always run seafoam and heet gas line antifreeze when I have to use ethanol blend fuel because the ethanol breaks down and turns to water
There goes the Edelbrock sponsorship…
White vinegar will clean all that white corrosion out like new!
Holly 4 Life
If it sits it shits. Fire it, flush, temporary tank on hand and you can find those restorations. Keep up the good work, the channel will grow. 🗿👽🗿
Thank you
Did you not put a new inline filter in. First move. If you can’t fix it. I’ll buy it. Lol
Yes, the truck has two of them
Marvel Mystery oil and or Sta-bal fuel stabilizer is your friend with this crappy ass gas you get nowadays
It ran real good til it didn’t!!
Why is it so hard to find a 54 Ford they are the first year of overhead. I had one at 18. And now I'm 71 I would like to find a 54 before I meet my maker
Those are definitely cool trucks.
The 53 looks like a 54 or the lower grill support behind the bumper. Has the holes for the grill.
It definitely seems like the 53 is easier to find. Perhaps because the 54-56 are more sought after and people just don’t want to sell them.
As long as I have been looking for a 54. 53 55 and 56 are easier to find . Or at least they are building them more than 54 . And that is my findings
You are getting high. From all the parts cleaner..
😂
This fuel is trash 😢
Oh boy, please edit out the use of God's name in any inappropriate way.. Much appreciated. Blessings!
Nice of you guys to think we are stupid the washer went down the port behind the one you picked the it out of. Go back on your videos before staging a recovery. We arent stupid and i personally find it offensive as hell to be treated like i am. I had subbed to this chanel but if your going to lie about one thing you will lie about everything.
Should I tell him or is someone else gonna
@@murray_1038I think he sees the gasket and spacer plate and thinks that those are separate ports.
@@chavronchavron1518probably
Maybe somebody needs to explain to him how intakes work…even I know how they work! 🙄
@@tashamurray3785 😂🤣