How To Remove Johnson / Evinrude Flywheel & Nut
ฝัง
- เผยแพร่เมื่อ 13 ก.ย. 2024
- 1 5/16 Flywheel Socket: amzn.to/2roo4PB
Evinrude Puller: amzn.to/2sFeZpG
I am participant in the Amazon Services LLC Associates program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to products.
I am fighting a 2006 Merc 90hp stuck flywheel, WD40 ed, impact gunned, steel hammer tapped, then watched your video, 5 min later, the rubber mullet did the trick, Thanks a million.
You help me so much Brandon. I look up something on one of my old outboards and you usually have a video about it! Thanks.
I’ll order that puller. I tried with regular puller as you did and the same happened first bent the bolts and shaft in the center from puller and doesn’t come out the flywheel. Thanks for every single video Sr, so helpful
Some of the best outboard videos I have seen.I have two johnsons.A 15(converted from a 9.9) and a 20. from the 80's.
Why thank you!
As I do more I'll probably get better at video quality and explanations.
Nice job, went fishing on lake erie today. My 1995 evenrude 200hp was great then 1/4 mile fron the ramp the magneto went out. You just helped a bunch with this video. Good luck 👍
Can you show how you line up the intake tubes when reinstalling
you just made my day a lot more simple so ill subscribe why not
Great video. The OEM manual list using OMC gasket sealing compound. Can I sub Permatex 80019 Aviation Form-A-Gasket No. 3 Sealant for this. Also this might be a stupid question but I didn’t see this addressed in the manual-does the sealing compound just go on the threads of the flywheel nut? Thanks
You can always put extra washers , that would help
Could u tell me what's melting under flywheel thanks
I have an '85 9.9 Evinrude and I bought the puller you recommended. But I cannot get the nut off in order to use the puller. How do I get the flywheel to stay in place in order to loosen the nut with my socket wrench. I have tried the rope method and the crescent wrench clamped onto flywheel (not on the teeth), but it still turns with my socket wrench. I assume it should be in neutral when removing the nut. Thanks for your help.
Do you by chance know the thread size on the flywheel.
Subscribed. Thanks man! this helped
you have 5500 subs now
I just picked up a free omc v4 and its missing the nut holding the flywheel. Do you if it takes a special nut, are they all the same, I have no idea what year this engine is. thanks.
Please help I rebuilt motor and timing is off I tried starting and it backfire please help me johnson 110 v4 outboard
i have a question .... i have a friend .. he have a vro 110 hp johnson and he was running and hit the bottom .. the motor die . he can't get it to start. is that possible the stator die at the time he hit the rock .... i test it and no spark on all four cylinder. do you think the power pack or the stator..... please help
When you re-install how do you know the correct positioning of the flywheel in order to ensure the timing marks are correct?
there is a key-way on the flywheel. Only one way to install it.
@@BrandonsGarage thanks!
Brandon do you know what to torque the head bolts at on a evinrude 150 horsepower
I have a 70hp johnson and have tried everything to get the flywheel off and cant get it ti budge. Heated the fly wheel, soaked in pen oil and WD40 and tightended it so tight it is bending my industial puller bar. Tapped it with a hammer on the puller bolt and no luck This thing is like welded on.
dont hit the puller bolt. Use a mallet. and hit harder than youre hitting.
Hold the veru end of the mallet, and get momentum up with your arm.
I don't recommend this, but another way to get that nut off without a flywheel holder is to seize the Pistons by overheating the engine.
haaaahaha!
I just spit water out my nose when I read that lol
I'm going to try that ... but on a friends motor ... heh heh
thank you , Brad - but can we make a ( video ) on how to make the ( flywheel ) turn after it has a hard time to turn when the ( start ) is ( engaged )_?
When/if I come across that problem, sure
جيد جدا
Brandon where can I get a stator for a 1983 blackmax 150 Merc and where can I buy that evenrude puller and will it work on my Merc flywheel?
Puller-
Evinrude Puller: amzn.to/2sFeZpG
Dont know much about the mercs.
hey there my crank shaft bolt is totally stripped to the point where my fly wheel nut wont go on....any ideas on how to fix that or should i just get one of those things like the tap and dies to fix it or do i just change the crank shaft? idk what to do but you should make a video on the crank shaft or if the bolt is stripped idk lol thanks
If I come across one, I will.
How stripped are we talking? Damaged threads on crank, or nut?
I imagine the nut would go first. Thats one strong crank.
well i have a 1998 evinrude motor worked fine then al of a sudden i hear some noises under the hood then i check and see the clips under my starter are broken and theres a plastic piece for that and it burnt off lol and my fly wheel nut is gone like un-repairable and my crank shaft bolt is stripped to maybe the 4th column of threads
oh btw its a 30hp
Ehhh, scary thought.
Hopefully nothing under the flywheel is broken.
i've turned it to the point where it wont hurt my gears and i just need a pulley but its hard to get one where i am lol plus what do you think of that crank shaft bolt? replace the crank shaft or fix the bolt plus i also hope nothing is broken under there
ok