have 2 vapes same one bricked one not trying to read the bricked one with clippers and it reads fine but the working one chip does't read dk why tho they both same
@@laboneinside sir kiya ap ne laga kar check kiya ha ya apnay experience se bata rahy ha? Q k ap to mostly is se achay programmer se hi flash karty ho gay
If you can't read the BIOS when it is on the motherboard then check the 3.3V coming from the CH341A programmer. The 3.3 V regulator might be weak. Perhaps it can only deliver 100mA. If other components on the motherboard draw current then the voltage might drop. So if you notice the voltage being low, perhaps below 2.8 V, then supply external 3.3 V to the CH341A after the regulator.
Excellent video s I am a beginner, thank you.
You made my day! Thank you very much for sharing! Neoprogrammer V2.2.0.10 supports *.cap files (ASUS) too! 🤩
Thank you sir this is the only video which helps me!
I did not know how programme a eprom. thank you irfan
Thank you for the lesson x
Exellent demo sir,very helpfull indeed😊
Good information
Thank you for the detailed explanation
That was helpful. Thank you!
hello sir ji thanks this video . sir w/o leg Wala bios keyse se program kare is ch341a programmer se pls 1 video bana do
have 2 vapes same one bricked one not trying to read the bricked one with clippers and it reads fine but the working one chip does't read dk why tho they both same
Thank you ❤❤❤
Sir ch341a ma ram adapter 24 wali side par lagy ga ya 25 wali side per?
25
@@laboneinside sir kiya ap ne laga kar check kiya ha ya apnay experience se bata rahy ha? Q k ap to mostly is se achay programmer se hi flash karty ho gay
Nahi check kia .
Would you know if the 93C46B 16-bit Serial EEPROM is supported by this CH341a programmer?
Good work sir
Very helpful thanks
thank you my brother.🙂
Hi, Ch341a v1.6 is it coming with a clip. that we don't need to remove bios from the motherboard? thnx
Clip didn't work on 95% motherboards. We must have to remove EPROM ic
If you can't read the BIOS when it is on the motherboard then check the 3.3V coming from the CH341A programmer.
The 3.3 V regulator might be weak. Perhaps it can only deliver 100mA. If other components on the motherboard draw current then the voltage might drop. So if you notice the voltage being low, perhaps below 2.8 V, then supply external 3.3 V to the CH341A after the regulator.
thankyou@@Drottninggatan2017
❤❤❤❤ thank you brother
My pleasure
thank you verry much
Bhai led adpter cable bnan ny ki video bna dy bhai
Is it possible to program plcc32 chip with this programer? (ch341a)
helpful , thank you
what program do you use to run the usb chip reader? Driver wont even install to see the sub.
Ch341a programmer software
Sir vdo as usual infmtve.wheres the software link
Link added thanks for reminding
Why do they have the jumper on pin 1 & 2 ?
Unlock mode.
Can i use it for AC eeprome
Ic number ?
Hi there, 1.8 Volt is it for Apple Devices? thnx
1.8v for latest laptops and Chromebook
thankyou@@laboneinside
merhaba. çip 1.8v tamam. ch341a 3.3v - 5v. ? 1.8v çip yüksek voltaj yüzünden zarar görmüyor mu? harici bir 1.8v adaptör gerekmiyor mu?
When you put in chip, it reconises the type of chip and it lowers voltage to that
Where can i buy bios chip for elitebook 840 g5 8th gen hp laptop
AliExpress
This ic all programs how much
I have this Programmer how to get software for this ?
Software link in description
Hello , i need information for programing control ( CY8C24423A ) by ch341 .
I want learn make read and write for that controller .
Not supported
ok . but i need any programmer can make that @@laboneinside
❤
Hi sir is there where I can download the software for this programmer for free please
It's all here - read the comment to the video up top.
not sure why you say unprofessional people, do you mean to say people that aren't engineers
My bad English I mean not a shopkeeper
❤❤
Kise agrez da bacha
windows on mac - bellisimo!
ssd 16gb
Aede Hindi nahi janta