Это конечно весело. Но если вы не заметили, эта штука, перестала быть трубой. К чему тогда, весь геморрой? Можно просто приварить два профиля, друг к другу, под углом.
I’ve obviously missed something here! When the pipe is bent to 90degrees, it is blocked, ie the open side butts up to the closed side. Therefore, there is no way for anything to flow or inserted through the pipe. Maybe that’s what is supposed to happen?
I suppose you could drill a hole in the right spot so it would wind up in the middle of the corner. But I guess most times it would just be structural with no wires or hoses.
Es imposible, si el ancho del perfil es de 10 cm., al trazar una diagonal debe ser más de esa medida y no los 8.5 que muestra, chequenlo y si estoy mal me corrigen.
is ds a sqr tube or rec tube?
🙏
You make "Macgyver" look like a slouch ! Your Amazing. Are you an Alien?
🙏🙏
what kind of pen do u use
🙏
Its a lot of bother to save a very small amount of weld ,,, but you can have a thumbs up as you left the guard on the grinder.
I like that you made the video feel like i was there with my ear up against the grinder, the deafening audio blowout was great!
Thanks 🙏
Please like & share my video sir 🙏🙏
Shabash ustad shabash
🙏
Good job bro I am from India
Thanks bro i m from in indonesia 🙏
Very good job
🙏🙏
Góc 90 độ
Please wear gloves . I had to pause the video
🙏
Hadir nyimak aktivitas anda yang sangat penting bagi saya...❤❤
🙏🙏🙏👍
Cm salah beri ukuran,yg 10 cm harusnya 6 cm 🙏
👍👍👍
🙏🙏💐
手の汚れだけでも職人さんだと伝わります。
Это конечно весело. Но если вы не заметили, эта штука, перестала быть трубой. К чему тогда, весь геморрой? Можно просто приварить два профиля, друг к другу, под углом.
I’ve obviously missed something here! When the pipe is bent to 90degrees, it is blocked, ie the open side butts up to the closed side. Therefore, there is no way for anything to flow or inserted through the pipe. Maybe that’s what is supposed to happen?
I suppose you could drill a hole in the right spot so it would wind up in the middle of the corner. But I guess most times it would just be structural with no wires or hoses.
Maybe it’s not meant for flowing liquids. Maybe it’s structural framing.
Rectangular tubing is rarely used to carry fluids. That's usually reserved for round pipes.
Estalar eu sei me ensina se o rolamento estragar como substituir ou este rolamento é furada
Super 👍🏻
Please pipe size
Looks like 1"x 3" or 1 1/4"x 3".
The wall thickness is close to 1/16"
Sangat hebat
🙏🙏🙏
思った完成形と違った😅
❤
🙏💐♥️
Said bend not cut
🙏
Маркер у тебя чёткий
🙏🙏
Top
🙏
But you haven't bent it to a 90 degree angle. You have bent it to two 45 degree angles.
His two runs intersect at a 90° angle.
@@edgargad2941 I agree, but that is not what the title says. It says "how to bend square tube 90 degree angle" and he has not done that.
Es imposible, si el ancho del perfil es de 10 cm., al trazar una diagonal debe ser más de esa medida y no los 8.5 que muestra, chequenlo y si estoy mal me corrigen.
Ci avevo pensato anch'io.
And that tube ain’t square buckwheat!
Damn straight, that's a rectangle.
Это называется: когда коту делать не...
🙏
Praca bez sensu.
У меня мозг сломался.
10 см размер не адекватный
🙏
Eso no es un tubo cuadrado bestia
Геморрой какой-то 😢
Не кто не будет платить за медленную работу. Вы хоть на штаны зарабатываете?
10cmじゃないやろ！
🙏👍
あ、そっち方向にね。
What's with the stupid sounds
🙏🙏
パーフェクト