Eric, my brother-in-law got me hooked on this show of yours. The best way to spend 30-45 minutes that I know of. I have been an aircraft maintenance tech since 1979...and no- one has ever given better advice that what I hear from you. I especially like how you mix troubleshooting videos and straight mechanical videos. Thank you! p.s. Those that like to nit pick on some of your methods, well good luck to them.
TH-cam automobile repair shop videos really dont get any better than this sir. I feel you are one of the pioneers of the medium. Just your motto of ' if I can do it, you can do it' has instilled confidence in countless viewers who have taken your advice. Me included. Thank you for letting us look over your shoulder all these years and allowing us into your home. I am very proud to have met you and shake your hand and add to the ice cream fund whilst dealing with family issues in your county.. You live in one of the most beautiful places on God's green earth. If I could nominate you and yours for a Nobel Prize in Humanity, I would. Thank you.......NJ
I did that job on my Frontier about a year ago. I cut the bearing cage and retainer off with a die grinder and called all of the shops in my area to press my new bearing back on. The lowest quote was $40 and the highest was $180. I felt that 5 minutes of press time for $40 was unfair, so I bought a 12 ton press and it worked like a charm and now I use it for other jobs too
The Toyota's are not that easy and you need to buy special adapters, I did buy a master kit that included the ability to install ABS ring reluctors which I don't think I won't ever use but it has all the needed adapters for a lot of other cars. I need to offer this service because the kit is quite expensive but a great investment.
I would buy that press in a heartbeat if I had the garage space for it. So far I've only been pressing bushings, ball joints, etc, so I can get by with a kit from Astro Tools I bought used.
@@blautensI had to get a rear hubbearing pulled off of a BMW single sided swing arm, big old son of a bitch. I found a transmission shop nearby that pressed off the old one and pressed on the new one for ten bucks while I waited. 😃
The torch, the welder, the rust. More carnage at SMA 👍
ปีที่แล้ว +39
Just FYI, Mr. O, thanks to your videos, I managed to correctly diagnose one guys wheel speed sensor issue from his symptoms description. I am not a car mechanic but software developer. :D
I have to agree Eric is the master and rainman Ray an average apprentice but I still enjoy the tussle he has getting rusty things apart, providing you have time and the same amount of patience Ray has😂😂
I did a similar job on my 1996 Mitsubishi Montero Sport years ago, which had both an inner seal and outer seal. The bearing wasn't too much of a problem getting off. The challange for me, though, was the bearing retainer. I didn't know at the time you had to grind it down to within an 1/8" of the shaft and then split it with a chisel the rest of the way. Found that out after a couple of hours trying a slide hammer, anything I could think of before finding you had the grind it. Got the bearing off, did all of the clean up, new seals, etc. and pressed the new bearing on and new retainer. I couldn't quite see all of the slot for the snap ring so put it back in the press and checking several times and still couldn't quite get all of the snap ring slot. So I muscled down on the press and heard a loud pop. I had just cracked the inner race of the bearing. Had to grind the NEW bearing retainer to get the NEW bearing off, so now I needed a NEW set. Since the full snap ring slot never came into full view, I started measuring. The retainer was OEM and had the same measurement as the old but the bearing was crossed referenced as the OEM was no longer available. The new bearing was approx. 0.015-0.020" or so wider than the old. There was no way I was going to be able to take that off the bearing so I filed and shaved it off of the bearing retainer instead. I pressed everything back together and got the snap ring back on. Success!...or so I thought. I went to put the brake backing plate back on and realized it needed to go on BEFORE the bearing and retainer. TAKE 3, and threes a charm. Finally got her all back together. Took me waaaay longer than it should have, waaaay more parts than it needed, waaaay more beeped moments coming from my mouth, waaaay less money left over afterwards; but hey, let's look at the bright side - I now consider myself an expert on Montero Sport wheel bearings. So if you ever get in a older model Montero Sport and need assistance, I'm your man! Umm, actually, that's not true, I don't want to do another one of those rear bearings. Please don't call me!!!!
When removing races I used to use a worn, small cutoff wheel but now I use a Dremel which is actually faster with a good, thin wheel. They work good on hardened steel. I cut a slit diagonally across the race, most of the way through and then I take a sharp cold chisel, put it in the groove and give it a good whack. That typically breaks the remaining steel of the race and it's grip to the shaft. The rest of the process is the same. Not quite as fast as the torch but arguably just as simple and an affordable option for anyone without torches.👍
I learned how to torch a huge line in the axle first time doing one of those, good times! Had to track down a new axle, drive three hours to pick it up, and pay for it myself. great memories lol I'm glad there's channels like this one out there now, for the sake of the younger generation wrenches out there! back then there was not!
The torch is still the fastest and in my opinion the best way to do axle bearings. That heat is not going to affect the integrity of the axle. Done it for over 40+ years and have never had an issue and some were race cars. Good job and great video & tips. Some day when I am cleared to travel by my Drs I will come to NY to visit my family & I'll swing by & shake your hand!
The "rethink that before you do" with the little tap on the axle housing had me laughing out loud for real. I love it. Good stuff here Eric. Keep up the solid work.
I went to all the parts houses for bearing race and sel kit with the part you torched off,if I were to do it again I would heat it up and pull it off, saving the collar,and reuse it.if race was good just a bearing replacement.
As always you have shown the common sense way to fix a car. I would like to add one thing. When an axle seal leaks I first remove the hose to the axle vent and try to blow through it. A moth nest can block it and make the axle build pressure which will push oil through the seal. I replaced the seals on my truck and found that was the cause. I give credit to my friend Tony for that.
I just got done tearing my Midwest salty dog yj front and rear axles bearings and seal,took 2 whole days on my hoist to pull all the parts off,4 hours to clean it all up and a whole nother day to put all the new parts back on,very satisfying for a fresh retired trucker,
Years ago before I had a garage or a press and needed a wheel bearing out I would remove the knuckles and take it to a local shop about 45 min before they close. It would cost $20 dollars and a case of beer to get bearings pressed out and new ones in on both knuckles. Then I would hang out and look at the hot rods or choppers they were working on after hours, good times!
Eric when it comes to Jeep's you saved me lot's of troubles mind was under Warranty yet you contacted Jeep for me and you got me back on the road to get my transfer case repaired in a neighboring state!!
My sister in-law and her husband are die hard Jeep fans that actually do take theirs off road. Sis in-law has a decal that says "It's a Jeep thing, you wouldn't understand". So me, being the wise ass that I am, told them "I caught your Jeep thing once and I had to get a shot". My wife and I prefer full size 4x4 pickups. Sure, they can't handle the tight trails but, we also trailer their Jeeps when we go on an outing together and the teasing is all in fun. Unfortunately, on our last outing, sis rolled her Wrangler 3-4 times down an embankment. Luckily, it was on a low speed trail and she has a full cage and 5 point harnesses so, the only serious injuries were to her pride and her Jeep. The Jeep is presently in my shop and she's already making plans for more modifications to it over the coming winter!
To put the bearing and the retainer back on , i learned a trick. If you put the bearing and retainer , or spacer whatever you want to call it , put them on a hot plate , just a cheap one from walmart , or even a electric griddle , heat to around 150degrees , and usually they will drop right on , to the axle a little tap with a piece of exhaust pipe or get a piece of gas pipe , slide over axle and tap it down , if bearing and retainer are hot enough they will go right on no problem ,wont hurt them , and when they cool down perfect fit . This also works for doing bearings in manual transmissions , if you dont have all the correct tools for the press , !!
Jeep is the Gift that keeps Mrs. Happy in the Shopping Mall and on Vacation. 😬👍 Can’t remember seeing a Jeep Wrangler in your Shop for a bit. Thanks! 👍🙏
Good Job, we love you videos! I lived in Michigan (Rust Belt) but I can't imagine doing that now. here in Hockley Texas Our vehicles will rust from the Gulf of Mexico salt water, IF you were to drive in the surf, but not so much from road salt. My service truck is a 1995 Chevy diesel, not much power, but 550,000 miles. many seats, seat belts, tires even Steering wheels.
I've done a few bearings and retaining collars in the past, and did them without a torch just using a large cold chisel and mash hammer, it has the same affect of relieving pressure making them easy to remove, replacing them was done with a length of sturdy pipe over the axle to drive them back on, standing the axle shaft on a bit of 4x2 timber between the studs to avoid damage. My coworker in the workshop used a torch and was no faster.
I did the same job on a 2008 wrangler about a year ago for my bosses daughter. I used a cut off wheel kind of at a diagonal on the lock ring and cut most of the way through, split it with an air hammer, and knocked it the rest of the way with a little hammer and a chisel. It took probably 20 minutes an axle, but I work in the south, so needless to say we don’t have a torch. 😂
DYI'd this on my 2010 JK, bought the loaded backing plates and pre assembled axles. Like wise had to weld the 4 retainer bolts to get them out. Now I have 2 axles to rebuild as spares at my leisure, still haven't cuz I got other stuff to do with my leisure. New sub and love the channel, the diagnostic stuff is way outside my wheelhouse but it's fascinating and educational none the less.
If you nick the axle and no one is there to be critical it doesn't hurt a thing. Did it many years in Toyota land. Sometimes you nick it. Never had an issue. If you running a bunch exta power I wouldn't but stock. No issue. Thanks Mr. O
Funny thing about the bearing I’d say is. There is a very good chance that SKF is the OE suppler to Chrysler for this keep. I know SKF was the supplier for my front wheel bearing on a 07 Dakota. 🙃
Happy Birthday!! back in the 70's i was workin' in auto parts store and we'd do axles all the time,, some truck axles were really long and the press would get all kaddy-wumpus pressing them on. never torched, press off- press-on
I have a Land Rover, one year older than that. From a distance, you'd think they'd be very similar. Both are solid axle 4x4s of about the same size. The rear axles are about as different as they could be. I've just done this job on mine and almost unrecognisable.
Such a basic, primitive bench press. Gives you total control and feel. You can work on my vehicle anytime. Only said that to 2 mechanics in over 50 years in transport.
Your work life calms and grounds me. I’m a wannabe mechanic, but my day job gets in the way. I hope you really enjoy what you do, despite the Chevy frustrations.
Exactly the same way I remove bearings, races, collars etc from shafts. 36 years in the industrial and mining world for me and I've never ruined anything. The best way to do it IMO.
I took my 9 inch Ford axels to a Autoparts store and they replaced the bearings. About 6 months later the right rear axel broke off at the bearing. It was over heated and lost the temper in the axel. Be careful to ask how they are going to remove the bearings. Or remove them yourself with a small cutoff wheel. Almost had a wreck in the highway when it broke off.
Unrelated to this exact video but we were driving from Philly to buffalo and I saw the Avoca sign and nearly lost it! We were picking up a berner puppy and I half thought about stopping by to say hi but I’m sure there are 1000 people A day trying to do that. Either way thanks for the content and all you do as an honest mechanic
I have the local ring and pinion shop do all my axle work as i dont have the tools and dont do it often enough to buy them. If it needs more than a map gas torch im not touching it. You made it look easy even though it isnt when pressing things on an off is involved. Good job!!
When are you top YT mechanics gonna do a "Mechanic exchange program" where you take those southern lovin wrench mechanics out of their comfort zone and make them work on a northeast special?
changed the rear wheel bearings on my Lemans. got the local garage to change the bearings . well i had seen the truck of a guy who rented from me he didn't like to pay the rent . so when i saw his truck at the garage i called the owner and alearted him to non payment . he thanked me for the heads up.
There used to be a great machine shop in my area. They did axle bearing, engine repair, and other work. Then the older guys retired. Now you go there they don't do this or that. Lot of parts shops are closing also. Advance Auto Parts bought Carquest and Pep Boys. Good job Mr. O.
As an industrial mechanic, when we have a bearing race on a shaft, We typically just heat the race with a torch and whack it with a brass hammer and it slides off.
I remember My Grandpa and My Uncle replacing rear axle bearing back in the 1970's ..They took a chisel and crack the race off the axle .then when they replaced the bearing .the used a section of metal pipe and slid it over the axe and drove the bearing back on with that pipe ..They didn't have a Press back then
I come here to learn how to do this stuff. Some of this I will never attempt. I don't think I'd ever have any suggestions because you clearly know what you're doing and have a tremendous amount of experience as well as the customers to show it. No reason at all to defend your ways, you're doing it the best way there is.
I grind collars and races flat (like your cut), and then hit it with a cold chisel at the thinnest part, and they just split and can be slipped off easily...great video, thanks...
I got phosgened one day, when a kid at a Chevy dealer I worked at before and after high school, in the 70,s. Was doing recall and campaign stuff to a car, the mechanic next to me tuned up a Impala, had the air cleaner off, and also was putting R12 in a ac, the valve froze open on the charge line or something, when removed, and engine sucked the R12 in carb, it cleared the whole shop in 10 secounds and showroom. I found out in 11 secounds why everyone was running out the door , when it felt like I was breathing fire in my lungs, never coughed so hard in my life, I was sent to the Quack house to get checked on by the quacks, gave me a respect for the WW1 guys in the trenches getting gassed, something I would never want to do again!!
Lol on removing the lock and bearing with the torch. I never have gas so I use a Dremel and cut off wheel. When the lock gives up its a satisfying snap. I did one recently and the axle including bearing and seal was the same price of the bearing alone. I wasn't paying attention and could have gotten it with a backing plate and bearing installed. Live and learn. ( I was replcing the axle too but looked at all the separate parts)
You sure know how to have a good time, Eric. Flame, Smoke, Loud Noises, and Brake Cleaner! It just don’t get no better!
You forgot about Andy stopping by. Lol
That, too.
Always love an Andy appearance! Yucking it up for the camera.
Your customer is someone who knows how to do things but also knows their limit. That's a good thing.
Eric, my brother-in-law got me hooked on this show of yours. The best way to spend 30-45 minutes that I know of. I have been an aircraft maintenance tech since 1979...and no- one has ever given better advice that what I hear from you. I especially like how you mix troubleshooting videos and straight mechanical videos. Thank you! p.s. Those that like to nit pick on some of your methods, well good luck to them.
Thanks man 👍🏼 Means a lot
@@SouthMainAuto Oh! This Guy again! Sheesh.. I'm airplane passenger - where's my shouout!
TH-cam automobile repair shop videos really dont get any better than this sir. I feel you are one of the pioneers of the medium. Just your motto of ' if I can do it, you can do it' has instilled confidence in countless viewers who have taken your advice. Me included. Thank you for letting us look over your shoulder all these years and allowing us into your home. I am very proud to have met you and shake your hand and add to the ice cream fund whilst dealing with family issues in your county.. You live in one of the most beautiful places on God's green earth. If I could nominate you and yours for a Nobel Prize in Humanity, I would. Thank you.......NJ
His Motto is ...."DEEZZZ NUTS" ( in a high pitch voice ) Get it straight.
I did that job on my Frontier about a year ago. I cut the bearing cage and retainer off with a die grinder and called all of the shops in my area to press my new bearing back on. The lowest quote was $40 and the highest was $180. I felt that 5 minutes of press time for $40 was unfair, so I bought a 12 ton press and it worked like a charm and now I use it for other jobs too
The Toyota's are not that easy and you need to buy special adapters, I did buy a master kit that included the ability to install ABS ring reluctors which I don't think I won't ever use but it has all the needed adapters for a lot of other cars. I need to offer this service because the kit is quite expensive but a great investment.
I would buy that press in a heartbeat if I had the garage space for it. So far I've only been pressing bushings, ball joints, etc, so I can get by with a kit from Astro Tools I bought used.
@@blautensI had to get a rear hubbearing pulled off of a BMW single sided swing arm, big old son of a bitch. I found a transmission shop nearby that pressed off the old one and pressed on the new
one for ten bucks while I waited. 😃
I have put the shaft in a freezer, and the bearing in a pot of oil on the old Colman stove.
I frequently add tools to the shop with that philosophy.
Happy early Birthday Eric O 27:05 @South Main Auto Repair LLc
Seeing Andy again reminded me that he should have his own TH-cam channel doing heavy duty stuff!
11/10 would subscribe
The torch, the welder, the rust. More carnage at SMA 👍
Just FYI, Mr. O, thanks to your videos, I managed to correctly diagnose one guys wheel speed sensor issue from his symptoms description. I am not a car mechanic but software developer. :D
Can you imagine Rainman Ray trying this repair? Get ready for a lot of carnage and an extra long 2 or 3 part vid!! Thanks for vid Eric.
I have to agree Eric is the master and rainman Ray an average apprentice but I still enjoy the tussle he has getting rusty things apart, providing you have time and the same amount of patience Ray has😂😂
I gotta hope Ray is a little bit of theatrics, sorta like professional wrestling. Still fun to watch.
Scotty could 😂
I did a similar job on my 1996 Mitsubishi Montero Sport years ago, which had both an inner seal and outer seal. The bearing wasn't too much of a problem getting off. The challange for me, though, was the bearing retainer. I didn't know at the time you had to grind it down to within an 1/8" of the shaft and then split it with a chisel the rest of the way. Found that out after a couple of hours trying a slide hammer, anything I could think of before finding you had the grind it. Got the bearing off, did all of the clean up, new seals, etc. and pressed the new bearing on and new retainer. I couldn't quite see all of the slot for the snap ring so put it back in the press and checking several times and still couldn't quite get all of the snap ring slot. So I muscled down on the press and heard a loud pop. I had just cracked the inner race of the bearing. Had to grind the NEW bearing retainer to get the NEW bearing off, so now I needed a NEW set. Since the full snap ring slot never came into full view, I started measuring. The retainer was OEM and had the same measurement as the old but the bearing was crossed referenced as the OEM was no longer available. The new bearing was approx. 0.015-0.020" or so wider than the old. There was no way I was going to be able to take that off the bearing so I filed and shaved it off of the bearing retainer instead. I pressed everything back together and got the snap ring back on. Success!...or so I thought. I went to put the brake backing plate back on and realized it needed to go on BEFORE the bearing and retainer. TAKE 3, and threes a charm. Finally got her all back together. Took me waaaay longer than it should have, waaaay more parts than it needed, waaaay more beeped moments coming from my mouth, waaaay less money left over afterwards; but hey, let's look at the bright side - I now consider myself an expert on Montero Sport wheel bearings. So if you ever get in a older model Montero Sport and need assistance, I'm your man! Umm, actually, that's not true, I don't want to do another one of those rear bearings. Please don't call me!!!!
This was a great story. thanks for sharing.
When removing races I used to use a worn, small cutoff wheel but now I use a Dremel which is actually faster with a good, thin wheel. They work good on hardened steel. I cut a slit diagonally across the race, most of the way through and then I take a sharp cold chisel, put it in the groove and give it a good whack. That typically breaks the remaining steel of the race and it's grip to the shaft. The rest of the process is the same. Not quite as fast as the torch but arguably just as simple and an affordable option for anyone without torches.👍
“This one’s spinning the stud too!” I think now you know why the DIYer hired you to do this.
I learned how to torch a huge line in the axle first time doing one of those, good times! Had to track down a new axle, drive three hours to pick it up, and pay for it myself. great memories lol I'm glad there's channels like this one out there now, for the sake of the younger generation wrenches out there! back then there was not!
A great Austin Powers loosening sequence followed by a dropped wrench ... classic. ;)
The torch is still the fastest and in my opinion the best way to do axle bearings. That heat is not going to affect the integrity of the axle. Done it for over 40+ years and have never had an issue and some were race cars. Good job and great video & tips. Some day when I am cleared to travel by my Drs I will come to NY to visit my family & I'll swing by & shake your hand!
As soon as the studs started turning I knew exactly why he brought it to you.
Love your sense of humor! "Girl you stink!!" 🤣
The "rethink that before you do" with the little tap on the axle housing had me laughing out loud for real. I love it. Good stuff here Eric. Keep up the solid work.
I went to all the parts houses for bearing race and sel kit with the part you torched off,if I were to do it again I would heat it up and pull it off, saving the collar,and reuse it.if race was good just a bearing replacement.
As always you have shown the common sense way to fix a car. I would like to add one thing. When an axle seal leaks I first remove the hose to the axle vent and try to blow through it. A moth nest can block it and make the axle build pressure which will push oil through the seal. I replaced the seals on my truck and found that was the cause. I give credit to my friend Tony for that.
Mason wasps, spider webs too !
I just got done tearing my Midwest salty dog yj front and rear axles bearings and seal,took 2 whole days on my hoist to pull all the parts off,4 hours to clean it all up and a whole nother day to put all the new parts back on,very satisfying for a fresh retired trucker,
Torch and Welder is Country Boy's Best Friend who does Mechanic Work on Everything...
I don't own a Jeep, never have, probably never will. But I watched the whole video because Dr O makes them all interesting. Thanks Eric
Another SMA job done professionally!!! What else would you expect? Bravo Eric.
Years ago before I had a garage or a press and needed a wheel bearing out I would remove the knuckles and take it to a local shop about 45 min before they close. It would cost $20 dollars and a case of beer to get bearings pressed out and new ones in on both knuckles. Then I would hang out and look at the hot rods or choppers they were working on after hours, good times!
Happy Birthday, Eric O! And always fun to have Andy stop by for some BS'ing with you, too!
Eric when it comes to Jeep's you saved me lot's of troubles mind was under Warranty yet you contacted Jeep for me and you got me back on the road to get my transfer case repaired in a neighboring state!!
One of the funnest times you can have is a spinning wheel lug on fancy wheels. Especially if they have stainless caps.
I just learned yesterday to put the bearings on the right way. Going to pick new ones up again today.
Your customer knew his limitations. Thank you.
I watched somebody struggle with one of these once.
Happy Birthday Eric O. (whenever it was) ✌
There’s always more then one correct way why people get tunnel vision is sometimes very entertaining nice video as usual
I love that you're DIY friendly
Happy Birthday..Old Son!!!...lucky year 44!!
im no mechanic eric just like to see a professional doing what he does best and man you do . regards from uk .
Love seeing you pull out the comment generators!
'Fit of rage' and 'Chrysler', two phrases that always seem to go together.
As the official bearing aficionado of this channel, it always brings me joy to see another video involving bearings.
another video without a bearing would be... unbearable.... 🤓
Just when I start catching SMA every other morning you go and make me wait one business week 😂
Sorry, deer season opened on the first haha
@@SouthMainAutono worries, hope you got one!
I don't know why but these videos make me smile. Keep it up Mrs. O's hubby.
BRAKLEEN SOUND EFFECT BABY! Might be my favorite thing on this channel. Makes me laugh every time.
My sister in-law and her husband are die hard Jeep fans that actually do take theirs off road. Sis in-law has a decal that says "It's a Jeep thing, you wouldn't understand". So me, being the wise ass that I am, told them "I caught your Jeep thing once and I had to get a shot". My wife and I prefer full size 4x4 pickups. Sure, they can't handle the tight trails but, we also trailer their Jeeps when we go on an outing together and the teasing is all in fun. Unfortunately, on our last outing, sis rolled her Wrangler 3-4 times down an embankment. Luckily, it was on a low speed trail and she has a full cage and 5 point harnesses so, the only serious injuries were to her pride and her Jeep. The Jeep is presently in my shop and she's already making plans for more modifications to it over the coming winter!
Sometimes as a mechanic your rage is all you need.
I missed the brake clean sound effect. It's pure gold.
The guy that said, “that job is larger than what I want”, now there is solid hunk of wisdom there.
Eric O you are a surgeon with the touch man
To put the bearing and the retainer back on , i learned a trick. If you put the bearing and retainer , or spacer whatever you want to call it , put them on a hot plate , just a cheap one from walmart , or even a electric griddle , heat to around 150degrees , and usually they will drop right on , to the axle a little tap with a piece of exhaust pipe or get a piece of gas pipe , slide over axle and tap it down , if bearing and retainer are hot enough they will go right on no problem ,wont hurt them , and when they cool down perfect fit . This also works for doing bearings in manual transmissions , if you dont have all the correct tools for the press , !!
I find great satisfaction when you use the air hammer. the torch is on another level..sanks Mr O
Jeep is the Gift that keeps Mrs. Happy in the Shopping Mall and on Vacation. 😬👍 Can’t remember seeing a Jeep Wrangler in your Shop for a bit. Thanks! 👍🙏
Jeep’s….
It was the sound effects, on the hot wrench tutorial...that made it worthwhile for me!
"Heat me baby one more time."
This is the content i needed.
Good Job, we love you videos!
I lived in Michigan (Rust Belt) but I can't imagine doing that now. here in Hockley Texas Our vehicles will rust from the Gulf of Mexico salt water, IF you were to drive in the surf, but not so much from road salt. My service truck is a 1995 Chevy diesel, not much power, but 550,000 miles.
many seats, seat belts, tires even Steering wheels.
I've taken tons of those axle lock rings off with a hammer and chisel. Works pretty well. They are very brittle and sometimes will just split.
You did an awesome job, Eric O. Appreciate you, buddy 👍
I've done a few bearings and retaining collars in the past, and did them without a torch just using a large cold chisel and mash hammer, it has the same affect of relieving pressure making them easy to remove, replacing them was done with a length of sturdy pipe over the axle to drive them back on, standing the axle shaft on a bit of 4x2 timber between the studs to avoid damage. My coworker in the workshop used a torch and was no faster.
I would definitely contract out that job instead of sitting in my driveway!
I did the same job on a 2008 wrangler about a year ago for my bosses daughter. I used a cut off wheel kind of at a diagonal on the lock ring and cut most of the way through, split it with an air hammer, and knocked it the rest of the way with a little hammer and a chisel. It took probably 20 minutes an axle, but I work in the south, so needless to say we don’t have a torch. 😂
Your customer made a great choice giving the job to you!
Love it when the torch comes out!!!
As someone from the rust belt I confirm the first tool to come out is the torch
DYI'd this on my 2010 JK, bought the loaded backing plates and pre assembled axles. Like wise had to weld the 4 retainer bolts to get them out. Now I have 2 axles to rebuild as spares at my leisure, still haven't cuz I got other stuff to do with my leisure. New sub and love the channel, the diagnostic stuff is way outside my wheelhouse but it's fascinating and educational none the less.
You may not believe it but I truly look forward to your posts. Thanks
Happy Birthday Eric & thanks for the awesome video!
I wish I had a gas axe miss my days on the railway cutting old rails for telephone & signal poles. Cheers Mr O another great video.
If you nick the axle and no one is there to be critical it doesn't hurt a thing. Did it many years in Toyota land. Sometimes you nick it. Never had an issue. If you running a bunch exta power I wouldn't but stock. No issue. Thanks Mr. O
You are a wizard with that cutting torch.!! 👍👍
Excellent video and I have watched many. I just turned this job away because I am also in NY and not equipped for when it goes sideways.
Funny thing about the bearing I’d say is. There is a very good chance that SKF is the OE suppler to Chrysler for this keep. I know SKF was the supplier for my front wheel bearing on a 07 Dakota. 🙃
Happy Birthday!! back in the 70's i was workin' in auto parts store and we'd do axles all the time,, some truck axles were really long and the press would get all kaddy-wumpus pressing them on. never torched, press off- press-on
I have a Land Rover, one year older than that.
From a distance, you'd think they'd be very similar. Both are solid axle 4x4s of about the same size.
The rear axles are about as different as they could be. I've just done this job on mine and almost unrecognisable.
Such a basic, primitive bench press. Gives you total control and feel. You can work on my vehicle anytime. Only said that to 2 mechanics in over 50 years in transport.
Oh goodie gumdrops a new SMA videa! - Thank you Eric.
Good point on the "being capable".
I find our NAPA to be a good source.
Good tip of the ratchet breaking off when dealing with hot hardware thanks
Your work life calms and grounds me. I’m a wannabe mechanic, but my day job gets in the way. I hope you really enjoy what you do, despite the Chevy frustrations.
Exactly the same way I remove bearings, races, collars etc from shafts. 36 years in the industrial and mining world for me and I've never ruined anything. The best way to do it IMO.
I took my 9 inch Ford axels to a Autoparts store and they replaced the bearings. About 6 months later the right rear axel broke off at the bearing. It was over heated and lost the temper in the axel. Be careful to ask how they are going to remove the bearings. Or remove them yourself with a small cutoff wheel. Almost had a wreck in the highway when it broke off.
Have a Happy Birthday! Always nice to have a friend stop by and break up the day.
Hell. The hot wrench works good. That’s the best way to get them things off.
Glad to See and Hear you’re Always Considerate of the Environment better known as Mother Earth. 😬👍😬
Unrelated to this exact video but we were driving from Philly to buffalo and I saw the Avoca sign and nearly lost it! We were picking up a berner puppy and I half thought about stopping by to say hi but I’m sure there are 1000 people A day trying to do that.
Either way thanks for the content and all you do as an honest mechanic
HAPPY EARLY BIRTHDAY Eric!!! May you have a GREAT day & a better year!!!
I have the local ring and pinion shop do all my axle work as i dont have the tools and dont do it often enough to buy them. If it needs more than a map gas torch im not touching it. You made it look easy even though it isnt when pressing things on an off is involved. Good job!!
Dremel and a cold chisel. Bought a press with the $ I saved. Easy job with that press.
When are you top YT mechanics gonna do a "Mechanic exchange program" where you take those southern lovin wrench mechanics out of their comfort zone and make them work on a northeast special?
changed the rear wheel bearings on my Lemans. got the local garage to change the bearings . well i had seen the truck of a guy who rented from me he didn't like to pay the rent . so when i saw his truck at the garage i called the owner and alearted him to non payment . he thanked me for the heads up.
There used to be a great machine shop in my area. They did axle bearing, engine repair, and other work. Then the older guys retired. Now you go there they don't do this or that.
Lot of parts shops are closing also. Advance Auto Parts bought Carquest and Pep Boys.
Good job Mr. O.
Happy Belated Birthday E. !!!
My dad was a Libra. Good minds, good sense of humor…yep sounds right.
Awesome to watch I just got home from camping chillin on couch now enjoying a SMA repair video
great job Eric.being skilled with the smoke wrench is a great asset.
2012 Jeep Wrangler has the highest recall rate of all Jeeps!!! trust me I know!
Hi Eric . Good tip on the sensor sometimes you find the best way to do things by accident not just on cars , woodworking etc .
As an industrial mechanic, when we have a bearing race on a shaft, We typically just heat the race with a torch and whack it with a brass hammer and it slides off.
I remember My Grandpa and My Uncle replacing rear axle bearing back in the 1970's ..They took a chisel and crack the race off the axle .then when they replaced the bearing .the used a section of metal pipe and slid it over the axe and drove the bearing back on with that pipe ..They didn't have a Press back then
I come here to learn how to do this stuff. Some of this I will never attempt. I don't think I'd ever have any suggestions because you clearly know what you're doing and have a tremendous amount of experience as well as the customers to show it. No reason at all to defend your ways, you're doing it the best way there is.
I grind collars and races flat (like your cut), and then hit it with a cold chisel at the thinnest part, and they just split and can be slipped off easily...great video, thanks...
I got phosgened one day, when a kid at a Chevy dealer I worked at before and after high school, in the 70,s. Was doing recall and campaign stuff to a car, the mechanic next to me tuned up a Impala, had the air cleaner off, and also was putting R12 in a ac, the valve froze open on the charge line or something, when removed, and engine sucked the R12 in carb, it cleared the whole shop in 10 secounds and showroom. I found out in 11 secounds why everyone was running out the door , when it felt like I was breathing fire in my lungs, never coughed so hard in my life, I was sent to the Quack house to get checked on by the quacks, gave me a respect for the WW1 guys in the trenches getting gassed, something I would never want to do again!!
This is why I have someone else do the job. 😁 5 minute job turns into a 5 hour job.
YOU make all jobs seem easy because you have All the tools and equipment it takes, great video....
Amazing; Any mechanic can instantly feel the prolonged bs feeling of a nut that just doesn't want to move!
Lol on removing the lock and bearing with the torch. I never have gas so I use a Dremel and cut off wheel. When the lock gives up its a satisfying snap. I did one recently and the axle including bearing and seal was the same price of the bearing alone. I wasn't paying attention and could have gotten it with a backing plate and bearing installed. Live and learn. ( I was replcing the axle too but looked at all the separate parts)