ไม่สามารถเล่นวิดีโอนี้
ขออภัยในความไม่สะดวก
Broken Graco Quickshot
ฝัง
- เผยแพร่เมื่อ 5 ส.ค. 2024
- Broken Graco Quickshot. I broke my Graco Quickshot and need to take apart! My Graco Quickshot is not spraying anymore after running 85 gallons through it. Stay tuned as I take apart my broken Graco Quickshot we will take apart the gun. Look at where the needle repair kit is located, solenoid trigger kit is located. How to remove the Graco Quickshot pump, hose and take a look inside. Lastly we will put back together the broken Graco quickshot.
Graco Quickshot Manual- www.graco.com/content/dam/gra...
www.mallerpainting.com
00:00 Introduction
01:25 Removing Cup and lid
02:26 Taking gun apart
05:14 Removing prime valve and pump
07:18 Removing hose
08:41 Circuit Board and Motor Assembly
10:32 Installing pump
11:15 Installing hose
12:09 Installing cover and prime valve
13:02 Putting gun back together
17:47 Installing new cup, lid and gasket kit
19:12 Closing statement
![Graco QuickShot [Tips & Tricks] Troubleshooting and PUMP REPLACEMENT](http://i.ytimg.com/vi/xehlmyRbwH0/mqdefault.jpg)
![Graco QuickShot [Tips & Tricks] Troubleshooting and PUMP REPLACEMENT](/img/tr.png)
![บุษบา - วงชานเมือง [LiveCoverVertion] Original : เมนทอล](http://i.ytimg.com/vi/Dm81sKcd9rs/mqdefault.jpg)
It was very generous of you to take the time to make this video and post it, which will be beneficial to many people, for sure. Great job! It looked like it was a bit of a struggle to turn the new cup to the "lock" position. You might want to lube the rubber gasket on the cup to make it rotate easier and potentially make the gasket last longer. Most people would probably use Vaseline, but I prefer to use MolyKote 111, which is made for such applications.
Yes great tip someone else recommended Vaseline and I’ve been using it. Seems to work great I will check out the moly cote 👌🏻
After watching a few videos online, there are a few other things you can clean. On the pump, there are large plastic allan sockets. There are 3 plastic ball valves that can also get clogged and cleaned out.
Thank you 🙏
Obviously it's very dirty and covered with paint, you need to use water to clean it after each job with water until it comes out clear, then run Miniral spirits to to get off anything that water didn't get then use Graco pump armor. Use extra strainer when filling the cup.
Thanks for the video was very informative on the inside of the machine cause I never had to go thru your situation fact is that mine would look brand new after each job fact is I use mesh bags around the unit and spray head, the hose would be covered with shield/Liner Cover.
Professionals keep their equipments in pristine condition.
Again, Thanks for the video.
One more thing, since you opened the machine you should've cleaned the inside and you can get the Graco QuickShot Outlet Valve 18H075 to repair the pump, cost $50.
Good luck.
Yes the machine exterior was very dirty. We sprayed almost 100 gallons through it in under 4 months spraying cabinet jobs. The machine did not fail from being dirty the pump took a shit. It’s a catch 22 with these machines. When your using the machine your putting wear and tear on the pump and when your cleaning the machine your putting wear and tear on the pump. All in all we turn enough profit to buy a new pump if need be!
Just bought one today. It'll be a complimentary tool to my Graco HVLP edge and procart. Trying to learn all the good and the bad. Thanks for posting this video
It’s mostly good! Don’t care for the lid but otherwise it’s a sweet little machine 💪
Thanks for the effort...
I have a truecoat that just went south... i called my local airless repair shop today -- he said not worth the cost of repair. Also he said once he opens the tc the integrity of the unit is shot.
Now here is his suggestion: he said the quickshots are coming in fast and furious. He said it's a great unit BUT wait another year while they graco works out the kinks
Interesting... thanks again. Fascinating
Yes I’m guessing after all the hype wears off the quickshot will come down in price significantly and maybe the will come out with an improved version. They are already improving the gun with the “power shot attachment” I don’t see why they wouldn’t add that gun on the quickshot next model. But we’ll see! Thanks for watching 💪😎
Thanks for video man. I bought one about a month ago and love it. Mine still works but love watching these videos for back up. Thank you for taking the time and showing us. I use mine to cut in ceiling with my shield and spraying the corners of the inside of the house. I’ve done 2 houses and cut my time by a lot. Oh these are new construction homes.
That’s a great idea! Yes even with a repair every 80-100 gallons they are still worth every penny in my opinion. Thanks for watching 💪
Thank for the break down brother, helps my minds eye when problem solving.
No problem 😉 after diagnosing my Quickshot it’s either the gun or the pump are the weak spots on these that break with heavy use. After trying the gun off my other quickshot it didn’t fix it so purchased a new pump and problem solved. Pumps are $239 and new guns are $339 hopefully help you when and if your machine breaks 💪
Hi Mate, Base in New Zealand, appreciate the reply and the help. keep making videos bro.@@mallerpaintingcompany
You were told by the repair shop what? I just replaced my pump because it exploded after about 45 gallons.... Having to wait a week for the new $275 pump theres an obstruction somewhere and paint won't flow properly.... Thanks for the video! New subscriber!
I got around 90 gallons before my pump went out. Gun took a shit around 80 on my other unit. But… I’m beating the crap out of them making money 💰 💪 thanks for the sub my fellow painter!
thanks for the video.
Top Tip for you, run some vasoline/patroleum jelly around the threads (plastic - and the metal of the tip guard) on the lid and also around where the white pot sits in the black holder, (not on the rubber seal though).
This stops paint drying and making it tight to remove.
Genius! Thank you 🙏 by the way love your station/ videos!
I used my quickshot yesterday. LOVED IT. Today… not so much. I got almost done with my project. I did make a mistake of my own and got a clog. I cleaned everything and started over. Almost got the piece done and it just stopped working. I can spray water. As soon as I spray paint I get maybe two passes and it just stops. I followed all the directions. Not sure I understand what to try
Definitely sounds like it didn’t get cleaned good enough and you have some dried paint in the machine that needs to get flushed through. Take the time and really flush it until there is no milky water coming out of the cup in the bottom holes and use warm water if possible you can buy a little pipe cleaning kit at harbor freight or Amazon to help also make sure your filter in the bottom of the cup stays put when you pour paint. I’ve had that come out and that is your only filter in the machine
Videos looking good in landscape
Thanks finally figured out how to use my camera 😂
Mine stopped spraying and i took everything apart like you did, but i also took apart the electronic gun, unscrew every piece in that gun and got to unclogged it, some paint particles got stuck the gun. It was hard to clean but now it s sprayes as it used to
Awesome! 😎 mine ended up being the pump but at least I’m a pro at fixing the Quick Shot! 🤣
keep it clean and the pump will last longer 🤪
🤘😎🤘
My quick shot went out today. Red light was blinking 4 times every time I tried spraying. According to the manual it needs a new motor or pump . I got early November and haven’t even ran 15 gallons through it. I spoke to my SW sales rep and they told me that it might be covered under warranty.
Yes sir it’s under warranty for 1 year after purchase as long as it was used responsibly. I’m guessing it’s the pump if you can hear it run when you pull the trigger but nothing comes out . That was the problem with mine. They are $235 for a new pump and a 20 minute fix either way
Motor is covered pump is not
@@matthewconnors6434 turned out to be the motor. Got it replaced free of cost to me. Graco for the win
It's the gun. I had the same issue. Apparently the solenoid which is the main part of the gun that pulls the needle in and out went bad. They sent me a new gun and I replaced it and it works fine again.
Yes the solenoid is a common failure and Graco will repair it for free in the first year one time if you keep receipt. However the new gun I purchased did not fix. It was actually the pump which is cheaper than a new gun 😀 and now I have a back up gun!
80 gal thays not bad i hear those other older hand helds lasted shorter
Not bad at all. I bought 2 and they are making us money so pretty happy with my ROI thus far
🤦🏻♂️why didn’t U take it back To Graco for a replacement🤔
I wanted to be first to make a fix it video for the Quickshot on TH-cam. So I put it through the wringer and 90 gallons + 4 months of wear and tear a was able to effectively break the machine. (The pump went out) this gave me the opportunity to be first to make a video dissecting the QS as I knew it would be a popular video. I was right! The video is just under 9k views and still getting 50-100 views per day 💪
Does the the orange gasket left on the table at the end not required to be replaced, or was it from another video, I did enjoy this one thanks
Great question! that orange gasket goes in the hose plug ins on both sides to make it water tight otherwise the water will fry your plug in and you will need a new hose. First time I pulled everything apart I was like where the heck did this fall out of 🤔 had to read the manual to locate where that gasket went!
So mine probably has 20 gals ran through and without a tip it sprays water but with a tip I’m not getting anything. Tried multiple tips
With the tip off, does it spray out water then just stop or does it just keep pumping water out?
@@mallerpaintingcompany yeah. But not strong enough to atomize with a tip in. Pretty sure it’s pump. Warranty sucks. Only thing it really covers is the motor
Yes then it’s definitely the pump then. They are $265 and about a 10 minute swap.
Would you recommend spraying fine paints of Europe hollandlac brilliant?
We only use waterbased through it so not sure how it will hold up to solvent coatings
@@mallerpaintingcompany I appreciate the reply. Keep up the good work 🤘🏽
If you use it only once without the filter it will get an obstruction likely in the top of the gun.....
Very true gun can get plugged easily
You've sprayed 250 litres of paint through it , your pump is dead
Not sure the liters conversation but 80-90 gallons and the pump went out yes this was in a 4 month period
Run Mineral spirits through it after use
If you’re using water based paints only then I probably wouldn’t. Just clean with warm water and store with a little pump armor.
dude, you sound like your high,, its no wonder its clogged , look how dirty the machine is..
Haven’t drank or used in over 17 years 😀 so definitely not high! We put close to 100 gallons through it in 4 months. And after my diagnosis we fried the pump in the machine. Approximately $265 and it’s back to work. The profits that were made in 4 months 5000x the amount of the part to repair
Take care of your tools , you deserve this for neglect !
Someday when and if you ever have a Buisness that does 1.2 million in sales per year you’ll be able to afford to fix the tools that make you money. Your comment is ignorant.
So disappointed the quick shots made out of mostly plastic and it cost more than a Titan 440 that's made out of metal
I agree they could definitely come down on price. Seems more like a $600 machine.
Tbh for a 2 thousand dollar machine it looks cheaply made over the phone at least.
I was able to purchase mine for $1115.00 and cleared 70k worth of cabinet repaints before we broke it. It’s a fantastic tool in my opinion. But your right it’s definitely not built like a Toyota
1200
Quick shot rapes on price!
I would never buy...
I can spray with 3.0 or 2.5 hvlp for less than a 100.
And I don't felt like I got bent over😢
I have 3 Graco 9.5s and prefer the Quickshot personally. But yes it’s still pretty pricey hopefully they’ll come down to 6/$700ish in a year like the other handhelds did