About 11:49 segment showing "Current Measurement" item: i'd like to read "Allegro ACS733" right under that function bloc, literally, because of its specific features (3.3 Volts, electrical isolation, 1 fast comparator/digital output, 1 near-distortion-free DC~50 KHz analog output)... So, as a suggestion my wish is to see some future version applying it all to portable/pocket induction drivers capable of "injecting" ~100 Joules "Heat Charges" into a 0.75 g "susceptor" within no more than 2 ~ 3 seconds on a pair of sturdy 3.7 Volts e-Cig batteries. Right now DiY solutions involve bulky RF Chokes which should get conveniently dealt with just by changing of topology, as illustrated by Infineon's MA12070 Class-D Digital Audio power amplifier for example, since it requires no large inductors...
I was simulating three level for audio, I use flying capacitor. However despite I use natural balancing it do not stay on zero volts, it just walk to positive and negative side, or when using a other mosfet driver i get that it go overlap, I use feedback for the audio system. I think differences in delay between mosfets is cause, but when set dead time bigger it stays nicely around 0 volts, I use symmetrical voltages. Is there a fault maybe with the dead times? I get als in time a bad suppression of the fundamental carrier so I think als to the delays, maybe bad models in ltspice. I can go try lossless parts in sim, like you do in Matlab.. thanks in advance.
Yes just keep in mind for low to medium voltage application give the capacitor value 4.7*e-3 F.For further explanation I will cover a separate video on that.
@@RanitSengupta what if the voltage supply is 400 -500 and switching frequency is 10k Hz can I still use 4.7*e-3 for dc bus capacitor and flying capacitor?
About 11:49 segment showing "Current Measurement" item: i'd like to read "Allegro ACS733" right under that function bloc, literally, because of its specific features (3.3 Volts, electrical isolation, 1 fast comparator/digital output, 1 near-distortion-free DC~50 KHz analog output)... So, as a suggestion my wish is to see some future version applying it all to portable/pocket induction drivers capable of "injecting" ~100 Joules "Heat Charges" into a 0.75 g "susceptor" within no more than 2 ~ 3 seconds on a pair of sturdy 3.7 Volts e-Cig batteries. Right now DiY solutions involve bulky RF Chokes which should get conveniently dealt with just by changing of topology, as illustrated by Infineon's MA12070 Class-D Digital Audio power amplifier for example, since it requires no large inductors...
Sir, please explain more on pdpwm in next videos.. Excellent work.. 🙏🙏
Is this simulink model pdpwm technique?
Yes here pdpwm technique is used for switching pulse generation
@@RanitSengupta eta ki 3ph naki single phase?
@@SkyTime yes it is a 3 phase model.but there is a another video part-2 you can see on this topic.
Nice
Thank you
Do you have PDPWM 5-level multilevel inverter!
Islam Alfirjani 5-level cascaded H-bridge multilevel inverter design video is already in my channel.
th-cam.com/channels/km2-lWdgn6rTuq9R6yh8rg.html
@@RanitSengupta Sir I haven't fund it yet maybe is a video hidden.
th-cam.com/video/V6M0LZsA_28/w-d-xo.html
Sir please explain for a 7 level flying capacitor multilevel inverter on how to make the PWM pulses
PWM generation is same as 3 level,5 level PDPWM.
PWM generation is same as 3 level,5 level PDPWM.
for multilevel flying capacitor control system what is there?
What you want know please elaborate.
You can ping me- ranitsengupta007@gmail.com
@@RanitSengupta okey
@@RanitSengupta how to make a control system for multilevel inverter using flying capacitor method? is there a video about it sir?
I was simulating three level for audio, I use flying capacitor. However despite I use natural balancing it do not stay on zero volts, it just walk to positive and negative side, or when using a other mosfet driver i get that it go overlap, I use feedback for the audio system. I think differences in delay between mosfets is cause, but when set dead time bigger it stays nicely around 0 volts, I use symmetrical voltages. Is there a fault maybe with the dead times? I get als in time a bad suppression of the fundamental carrier so I think als to the delays, maybe bad models in ltspice. I can go try lossless parts in sim, like you do in Matlab.. thanks in advance.
Please ping me your design by mail-
ranitsengupta007@gmail.com
Hi sir, thanks for the vid! But how did u calculate the value for main dc bus capacitor and the flying capacitor?
Yes just keep in mind for low to medium voltage application give the capacitor value 4.7*e-3 F.For further explanation I will cover a separate video on that.
@@RanitSengupta what if the voltage supply is 400 -500 and switching frequency is 10k Hz can I still use 4.7*e-3 for dc bus capacitor and flying capacitor?
@@wickbron8964 yes you can use this for your design.if you are facing any problem with this value then ping me.Part-2 will upload within 2 days.
Assalamualaikum pak, untuk sistem control multilevel flying capasitor apa ada?
please three phase 5-level inverter pwm
Please design 3 phase 7 level CHBMLI using PWM technique
Yea sure
@@RanitSengupta Thank you sir, please design as soon as possible
Nice