Nissan Qashqai Rear Brake Pads Change. Electronic Hand Brake Rewinding Without any Diagnostic Tool.
ฝัง
- เผยแพร่เมื่อ 5 ก.พ. 2025
- Nissan Qashqai Rear Brake Pads Replacement Job. Nissan Qashqai Electronic Hand Brake Rewinding Without any Diagnostic Tool to Change the Rear Brake Pads.
#nissanqashqai
#electrichandbrake
#rewindingcaliper
Disclaimer:
The content used in my videos are intended for educational and informational purposes only. I do not take any liability or responsibility for any damage caused while viewers trying similar type of practices on their properties. All rights to the images, music, clips, and other materials used belong to their respective owners. I do not claim ownership over any third-party content used.
Copyright Disclaimer:
Under section 107 of the copyright Act 1976, allowance is mad for fair use for purpose such a as criticism, comment, news reporting, teaching, scholarship and research. Fair use is a use permitted by copyright statues that might otherwise be infringing. Non- Profit, educational or personal use tips the balance in favor of fair use.
I would like to thank you first for your time and video it's help me to replace my rear brakes in Australia Sydney thank you bro
You are welcome thanks 😊
Best DIY video I've seen regarding Nissan/Renault brakes! Thank You!
Superb video thank you very much. Step by step instructions and crystal clear instructions 10:10
Thank you 😊
I noticed your original pads had the metal back plates. The Bosch ones I’ve got to replace my worn ones don’t have them!
Do I need to transfer that plate over from the old pads onto the new ones?
Or are the new ones supplied without them because they don’t need them?
Thank you
@@CBR-Spikes46 no u don't have to. Different manufacturers do different designs. Good luck 👍
@@diykhan perfect thank you very much. Hopefully the t30 motor bolts play ball and don’t round off 😂
You sir are a legend. You have a pleasant personality
You are welcome thanks 😊
Hi Mr Khan.
I attempted brake pads change today, & discovered that I had to turn that internal spline clockwise all the way in order to allow me to compress the piston.
Regards.
This is right I found out the hard way, I accidentally turned it anticlockwise and the piston came out too much, I couldn't push it back in so I had to end up buying a new caliper to sort this out!
Thank you for this. Where did you put the trolley jack to jack the car up, was it the jacking points or somewhere else?
Great video! I’ve just done the rear pads and discs on a 2014 Qashqai and this helped a lot 👍
Thanks 😊
Did the two torx bolts come out okay?
@@JackScott-95 they were a bit stiff so had to be careful with them but they came out ok
@@lukewade7744 Thanks mate 👍
@@JackScott-95 no problem 👍
Morning Sir after someone changed my rear pads the electronic hand brake light is off but it's still working any advice thanks again
Hello, when you removed the electric motor, you turned the adjustment knob in the on direction, shouldn't it be turned in the off direction?
Should the parking brake be released before starting the operation thank you.
Thank you for the video. I'm going to do my friend's Nissan brakes soon and was wondering if I need to get a rewinding tool. It is so nice that I can remove the motor and don't need any extra tool, just something to push the piston straight. Good to know. Thank you again!
You are welcome thanks 😊
Fantastic vid Mr Khan 👍
@@ConfusedAtom-lp3sj thanks 😊
Thanks for the video, are the epb motors 'handed' ie to rewind them is it left hand thread one side, right hand thread the other?
Yes when u turn it u will see which way to turn to rewind the piston.
HEEEELP.
I did as you said, everything, poing by point, but my piston does NOT go back, no matter how hard I press. I unwinded the motor as you said, but nothing, seemes stuck.
I think it is because the circuit is in pressure, what can i do?
Did u discount the electric motor.
It could be to do with piston too much Rusty inside
@@diykhan no, i made it using a different tecnique mentio ed in anorher video, but i guess it is better if you to tell people how to disengage the handbrake first.....if you don't do it, it is impossible to remove the caliper
DId your tool have 2 pins or 3?xOn the 1014 model it requires 3 and i can't find the tool to match.
This one had two pins. Good luck 👍
Brilliant job Mr Khan!
Thanks for your appreciation. Please like share and subscribe my channel. Thanks
What is the name of that tool you used to push the piston back? Is there an alternative way to do it - push the piston back. Thanks a lot for sharing.
Rear brakes tend to be on a screw that the hand brake rotated to push the piston out so a "brake rewind tool" is best although I've managed a few with needle nose pliers and turning it by hand front ones just a G clamp pop the old brake pad in and clamp the piston back in tends to be faster just remember to not twist or pull on the flexible brake hose and dont pinch the rubber seal around the piston and you can't really go wrong if your unsure ask for help
Did you had the ignition on and parking brakes off? Or the opposite? Thank you for the video
Ignition off and hand brake off.
Thank you
Good video very easy to follow…once you’ve changed brake pads on cars with electric hand brake do you need any sort of computer to reset any sensors etc does anyone know??
No really. It should adjust itself when u engage it and then disengage it few times
Thanks for answer very helpful great helpful videos also please keep them coming….👍
You are always welcome
Do you have to release the hand break before you open the part from the caliper?
@@AmirKhgh-pj5ey yes release the hand brake. Make sure you put something in front of the wheel to stop the car from rolling forward or back.
@@diykhanthank you🙏
@AmirKhgh-pj5ey you are welcome 😊
Worked a treat, only took about an hour to do both sides.
Well done 👏
Great video.very well presented,How do you put the hand brake on service mode
To not make it engage when turning off the car? Push and hold the e-brake button down while turning off the car and it will not put the brake on.
Nice 👍
Excellent work. I will recommend everyone 👌
You are welcome thanks 😊
Hi buddy you winding clockwise inside caliper before pushing it back
How did you keep the handbrake off as mine comes on as soon as I switch it off?
Great job sir helped a lot
Thanks dear.
Great vid, happy to do mine tomorrow
If you don't use a diagnostic tool,just simply apply 12v to motor terminals.That is the easy way.Cheers
Salam mera baei. moche pta ne chalega ke abka peshtom ne raid pechne os akhr tak ponchgia? shukria
I’ve just done mine and now I’m getting a flashing handbrake light and can’t work out why that is. Any ideas? I’ve bleed the brakes just in case it was that and it’s still there.
Have to apply handbrake few times.
Seems like the piston is stuck at the rewind position
There is video on you tube. After replacing brake pads. Flashing lights.its normal. But you need to do something. If find the video I will send you link
Hi guys. I followed this amd worked a treat but i now have a parking light flashing on my 2017 quashqua. The handbreak works but doesnt automatically. What do you think has caused this? Thanks all
It might needs a recalibration
Via diagnostic machine
On other videos they say don't disconnect the plug otherwise you get a fault light on
Excellent video thanks
Thanks 😊
U literally are the best 👌 👍, u save me $500bucks buddy
Thanks 😊
I have a qashqai j11 e hand brake won’t release any ideas what to do car is stuck at school
Have you checked the Fuses. Does it make noise when u press the release button.
Can you push the piston back with the motor on it?
On it will damage the motor
Thanks for your response@@diykhan
You can rewind the piston with top level diagnostic machine aswell. You go into the brake pad replacement or service option n thats where it gives you option to rewind or reverse the caliper pistons electronically. Good luck
i unfortunately do have the diagnostic tool so will go with this method@@diykhan
@@Marcus_Govender ok best wishes
Was handbrake on or off!! Cheers gonna try mine tomorrow
It was off.
How do you take handbrake off and it stays off!! I’ve got kadjar! Be same won’t it!! All same
Yes hopefully its going to be same nissan renault parts.
Thanks a lote.....🙏
You are welcome
Salaam brother
Very nice video MaShaAllah.
Where is your workshop located or you do Mobil service. Please advise thanks.
Thanks for your support. I work as a mobile mechanic.
excellent video thanks
You are welcome thanks 😊
If like me the torx screws are worn on the rear of motor, use a 9v battery to rewind the motor
Great bro stay blessed 🙌
My pleasure 😊
You make it looks so simple. Just one question is the procedure the same on a 2019 Qashqai . Thank you so much...
Yes it is same on 2019
Do you have electric handbrake On or Off when you start this job ? Thanks
Off
Silly question is this the same as a Renault Kadjar 2016 with EPB and is it better to do both sides of vehicle before reconnecting the parking brake?
It should be same and I would do one side first then go on to the other.
Thanks DIY Khan
If you're replacing your own brake pads, chances are the vehicle is a few years old and the torx bolts on the motor will be corroded. This method wasn't possible for me. I found that applying 12v to the motor terminals was the only way to retract the handbrake.
cool
👍🏻👍🏻
My pleasure 😊
You can see he has put grease on pad with his hands and put it like that on the disc on the inner one :))
I did clean the grease left on the discs with brake cleaner.