Looks easier in this video than it is depending on your type vehicle. I strongly suggest discarding all the hardware and getting 1/2 inch self tapping screws. You may or may not need to drill pilot holes if pedals are metal. It will save you time and headache! Plus the chances of them coming off are slim to none. ( I purchased a different type of pedal with multiple holes which made the adapation easier.)
These brake and gas pads are dangerous.Depending on the model car one has my new pads were too close on my gas and brake pedals my footwear would at times press both pedals down I thought I had to just get used to them but I was sadly mistaken.I was approaching a stop light and went to hit my brake instead I accelerated right into the back of someone car my headlamp cracked and left front bumper is hanging off the other car had minor scratch and didn't pursue any insurance payment. I explained to him what happened it was an innocent mistake my drivers license been clean for over 30 years.I will start my own repairs tomorrow. I've taken those dangerous pads off my car so be careful with using them.
Both you guys forgot to take off the black plastic rubber on the brake and the gas pedal,which will cause these covers to slip off,and the nuts come out fast with strong vibration caused by the rubber padding.i had to learn the hard way..they should tell people this in the directions
@@kash662nah he’s talking about the factory pedals. Some cars (mainly older), the foot pad on those pedals aren’t attached to the pedal arm usually just snapped on like a lego piece
I strongly suggest to buy a pack of mini split washers to add onto the nuts, to eliminate the nuts vibrating loose over time and to finish the tightening with an electric screwdriver set to max torque, just so the tightening is quick and less awkward.
Hi! Very good idea but can you please send a link with the Mini Split Washers ? I was trying to found some but nothing on amazon or ebay. Please if you have time just to send a link and the good size. Thank you
You're absolutely right because my new brake pad cover screws loosened in two areas after I tightened them and it can be dangerous while driving if pushing the loose brake pad that's touching the gas pedal causing the car to unexpectedly accelerate.
I have now removed these and gone back to the original factory pedal covers because the color fades easily and looks very ratty. Very poor wear-resistance with these color metal covers. They only look good for a month or two
I got a 2011 Nissan Altima and the brake pedal gave me a hard time too but after over tightening it I got it to stay. The gas pedal is the one fighting me. It don't matter hoe tight I get it the damn thing won't stay. I even tightened it so tight the screws pulled through. It's in the passenger seat til I figure out what I'm going to do to make it stay.
We try and try and try and it’s so hard to put them on😢 we can’t put them on. I will go pay some one to do it for me lol cause it’s so hard tan put them on😅
I bought these off shein for really cheap- but after reading the comments I’m just not gunna bother installing them I rather waste $3 then $$$ getting my car fixed due to negligence.😢
I got these and i am not happy. They only look good but they keep coming loose and it is hard plastic very slippery. They should not be called Non-slip
I tried it on my truck.. seems like its not a good fit.. but it says on the package it can be installed on Cars, SUV, or Trucks.
Very nice work!!! It looks relatively simple to install and I agree with the previous comment about adding split washers
Thank you !!!
I bought the same exact ones for my 96 F-150, but the holes on these aren't spaced enough for the existing pedals...
Not fitting on a tundra neither
Looks easier in this video than it is depending on your type vehicle. I strongly suggest discarding all the hardware and getting 1/2 inch self tapping screws. You may or may not need to drill pilot holes if pedals are metal. It will save you time and headache! Plus the chances of them coming off are slim to none. ( I purchased a different type of pedal with multiple holes which made the adapation easier.)
These brake and gas pads are dangerous.Depending on the model car one has my new pads were too close on my gas and brake pedals my footwear would at times press both pedals down I thought I had to just get used to them but I was sadly mistaken.I was approaching a stop light and went to hit my brake instead I accelerated right into the back of someone car my headlamp cracked and left front bumper is hanging off the other car had minor scratch and didn't pursue any insurance payment. I explained to him what happened it was an innocent mistake my drivers license been clean for over 30 years.I will start my own repairs tomorrow. I've taken those dangerous pads off my car so be careful with using them.
Both you guys forgot to take off the black plastic rubber on the brake and the gas pedal,which will cause these covers to slip off,and the nuts come out fast with strong vibration caused by the rubber padding.i had to learn the hard way..they should tell people this in the directions
Ok so they need a warning “Must have common sense to operate “ 😂
@@Treyhottabeatzwait so that whole black piece needs to come off? Like only the red piece is needed?
@@kash662nah he’s talking about the factory pedals. Some cars (mainly older), the foot pad on those pedals aren’t attached to the pedal arm usually just snapped on like a lego piece
Thank you.
Would this fit in Toyota corolla 2014 hatchback
Видео где всё наглядно и понятно без слов. Браво🎉👍👏
Something I need, but the way you secure it I feel can be better
I tried putting it on but it’s hard
Thank you! Very helpful I was breaking my head for a sec.
good video, specially you managed to get the camera lens focus back of the paddle at the end, great! 👍👍👍👍👍👍👍👍
so effing cool! Looked complicated but you made it look so smooth to install :)
I strongly suggest to buy a pack of mini split washers to add onto the nuts, to eliminate the nuts vibrating loose over time and to finish the tightening with an electric screwdriver set to max torque, just so the tightening is quick and less awkward.
Hi! Very good idea but can you please send a link with the Mini Split Washers ? I was trying to found some but nothing on amazon or ebay. Please if you have time just to send a link and the good size. Thank you
@@alexandrubalanDBX m3 washers
You're absolutely right because my new brake pad cover screws loosened in two areas after I tightened them and it can be dangerous while driving if pushing the loose brake pad that's touching the gas pedal causing the car to unexpectedly accelerate.
I have now removed these and gone back to the original factory pedal covers because the color fades easily and looks very ratty. Very poor wear-resistance with these color metal covers. They only look good for a month or two
great video but now the brake pad one keeps loosing up n falling off any suggestions ?
Threadlock or plumbers tape
Good fit, jus noticed you did not apply fliers to press the metal plate against the back pedal as shown in the manual, no longer needed bro?
Huh?
He did apply them, its even shown at the end of the video
I bought these exact ones for my 2019 corolla the gas one fits great but the brake one pain it falling off and I to cut because it was too wide
I got a 2011 Nissan Altima and the brake pedal gave me a hard time too but after over tightening it I got it to stay. The gas pedal is the one fighting me. It don't matter hoe tight I get it the damn thing won't stay. I even tightened it so tight the screws pulled through. It's in the passenger seat til I figure out what I'm going to do to make it stay.
I bought the same ones for my 2010 accord and the brake pedal cover is giving me hard ass time cuz it doesn’t cover it fully
ok
I have the same car and I’m having the same problem. Did you get them on?
@@Nate0289 no I just took them off and put them away I’m gonna buy different ones
Having the same problem with my 04 accord coupe
@@ShiroyashasamaThank you 👍 I'll be looking for a different set soon
How do you take off the old gas pedal. It doesn't shoe. And I tried looks like a pain
Uhm, u don’t. These go over the existing pedals
@@wildwildwestslmao
kwid climber ko laga sakte hai kya ?
Any advice for a 2007 Mercedes Benz? I got the screws in & that's it..😂
So do you need to remove the pad on the pedal itself to apply this or should you leave the pad on
No need to remove. Just leave the pad on.
Please subscribe for more videos. Thank you.
It depends on the size of the pedal If it is larger then you may have to remove it
@@djayzul Yes the rubber pad grip stonger then the metal plate
Why dont they come with lock nuts?
Very helpful, I have the blue sport pedals
what's the another name use for padel brake?
Will this work my 05 nissan altima?
what's the synonyme padel brake?
i don’t this works on my lexus es 300😢
hello can it fit corolla 2021 brake is 8cm length 4cm width accelator 5.5cm length 8cm width
Do you need to remove the original rubber off the pedals before you place the new ones on? Or does it just go on top ? Many thanks
Just go on top. Thanks for watching!
I have the royal blue ones on the way now
you made it look easy I just got the grey ones on the mail!
a large metal surface is very slippery so i dont understand as the bottom of shoes are all rubber for a reason seems more slippery then original ones
very helpful 🙋🏻♂️🙋🏻♂️ thank u so much 🙋🏻♂️ from Malaysia "
Thanks sir.. please subscribe my channel. Thank you.
Thanks 4 the video my 1s didn't come with instructions
Perfect job mate
Thanks mate. Please subscribe my channel. Thank you.
Thanks for that back view at the end needed it have a nice day #🔵
Karon kabalo nako onsa.on pagkabit😁😁 slamat idol
Mine don’t even f fit spent 45 mins and nope doesn’t fit on mine bmw x1
Молодец четко и ярко все показал
Thank you, really needed this!
thank you for this video! I needed it!!
Link please
thanks for video, but after i installed i did not feel unsafe when drive the car like that, i take them off. Thank you anyway
Very helpful. Especially since I have the exact same ones except mine are blue
nice, how did you film this lol
Thankyou i just ordered this at shopee and hope it works well
It was very explainded. Thank you
Thank you!
Gracias!!..no te is ni idea cómo era que se ponían jj 👍
No meu reforcei com fita dupla face ficou top
We try and try and try and it’s so hard to put them on😢 we can’t put them on. I will go pay some one to do it for me lol cause it’s so hard tan put them on😅
Sandle Knotting Is Opinionated Although Brake Is Greater Velocity Adjustment To Clutch From Cruise Slow
Free Suspended Knot Left Large Toe Socked Smoother Clutch
Magnet Density Matters
Thanks a lot…..very helpful….got the silver for my 4Runner
I jus put the blue ones on my 98 4 lrunner
thanks for not showing us how you took off the plastic.
they look pretty thin and cheap, hoping for a quality assessment, but that's ok. thanks for the video
Thanks you. Great video. It helped alot
Thank you 🙏..
Thank you so much!
Ohhhhh damn I thought it just came with a cover.... not a pedal too!
Thank you for your help and I love gas pedal and the brake pedal too
Thanks a lot!
I bought these off shein for really cheap- but after reading the comments I’m just not gunna bother installing them I rather waste $3 then $$$ getting my car fixed due to negligence.😢
Very helpful thanks
I was going to buy these but they seem dangerous considering the bolts can become lose while driving 😢😢😢
You could also put a little threadlocker on the screws. Combined with lock washers, they should stay in place.
@@James-gl3twNot always. It can become worn eventually and may need to be replaced because you use an acceleration pedal more than a brake pedal.
Good decision - they are dangerous.
Thanks
touch screen car pedal to put your feet on levitate car pedal
I didn’t get my hardware
Sir ano sasakyn wrong kinakabitan mo
Vios sir
I got these and i am not happy. They only look good but they keep coming loose and it is hard plastic very slippery. They should not be called Non-slip
Good job.tnx bro😂😊
Thanks sir for watching. Please subscribe.
Helpful thanks
I got these for 4 dollars on temu
Amazing.
💀
Muchas gracias muy bien espléndido excelente
After watching your video I'm about to trash those shitty instructions thanks
I jus put my on there was a bitch to put on but he did it so effortlessly
Selalu tertangal yg dkt padel minyak hmm
THESE DO NOT I REPEAT THESE DO NOT WORK FOR ANY DODGE CHARGERS OR CHALLENGERS
Good video thank you
Thank you Lil’ Sarah Starr. Please subscribe my channel. 😉..
@@djayzul ok!!
@@Sarahstarr1000 thank you
just orange color
This was video was useful
Thank you ☺️
Dont do this for 2006 jeeps its not going to work
The don’t look safe 🥺for my opinion
U right I brought these but know if I should put them on
Don't - they're dangerous.
กิ๊บล็อคฝากระโปรง
MAS OK NA PEDAL ITO KUMPARA SA DRILLING SIR
Oo sir. Madali lang sya iinstall.
Maganda ba quality sir. Fit sa gen 2 Montero?
Gawa Kapa vlog iba
Oo pre.. para sayo 😆..
Hosmuch
cool thanks 👍
Very helpful thanks