hello. can change the encoder to other branded encoder with similar specs than original, and can be recognized in the driver/aplifier? in my case incremental 3 pair phases(A+A-B+B-Z+Z-). (servo Sanyo Denki Q2AA13150H/Driver RS1A05AA) greetings
@@nikhiljambhale1533 hello Mr. Nikhil. I have an Yaskawa SGDM 50 ADA Servo Motor and Drive on my machine. Its giving an error of encoder communication. Can you help change this Encoder? 🙏
Calibrate the encoder using a dual-beam oscilloscope. In short, the corresponding phase of the supply at the first input of the oscilloscope, and on the second - Z. This is if you did not mix up the phases and the shaft did not move much, otherwise you need to turn 120 degrees and catch the approximate position to find the correspondence of the encoder phases with the motor phases. Then, using a drill (not quickly), turn the rotor and precisely install the encoder. Two signals with a phase shift of 90 degrees must coincide. I'm writing from memory, maybe I'm a little wrong. If necessary - I will find the records - I will clarify. Sorry for my language - I am writing through a translator.
Bay maayong adlaw naa kuy problema sa kong alaga, na machine bay servo motor japon halos dumogo na ang utak kuh sa kaka troubleshoot ginawa kuna rin ang mga nakalagay s manual nya peru wala parin ang problema bay wala akong pamali na amplifier at wala din akong servo motor na spare din. Kaya hirap na hirap ako bay
Maybe you don't need it, but... I saw two reasons for the jamming of the 750 W (Sigma1) motor. 1. Two wires to the motor (phase) are shorted - slows down. I had this in the socket. 2. We disassemble and clean the metal shavings on the rotor. Namely, it is on a magnet. We use plasticine, chewing gum, etc. At the same time, it is undesirable for the stator to be without a rotor for a long time - it is desirable to insert at least a metal tube at that time, or (quickly clean the rotor and return it to its place). I disassembled several pieces - they all spin. I did not put them on the machine, but I will calibrate them (encoder). Sorry for the bad language (through the translator).
Congratulations, warranty voided and a motor that likely will not run. Motor Commutation is based on the encoder pulse alignment.
Hello, what model of servo motor is it? ... I would like to know all its characteristics
Do you have the encoder wire connection description
No need calibrasi againt?
hello. can change the encoder to other branded encoder with similar specs than original, and can be recognized in the driver/aplifier? in my case incremental 3 pair phases(A+A-B+B-Z+Z-). (servo Sanyo Denki Q2AA13150H/Driver RS1A05AA) greetings
From where we get spare part Ml694v-0
Next time you can make video of encoder replacement for GSK servo motor.
I need encoder for my servo motor , how to contact?
Hi, where can I find this encoder? I have the similar servo motor I need to fix.
Thanks
at ebay
Hello, can I know the type of the motor, I mean, synchronous or non-synchronous without opening it, and how is that? Thank you very much
Most servos are synchronous
Can you share price of this encoder?
I need help with encoder
Can I get servo motor inporter in Bangladesh?
wondeful
nice
can i get an encoder
Very nice
please tell your friend to subscribe my channel Thanks.
where you buy this spare, please?
At aliexpress
Hello sir, I want CMOS back up file for motoman yakawa NX100 robot can u help me...
Hi po. Do you accept repairs?
Hi? Change okey but angle?
angle i can change you
@@nikhiljambhale1533 hello Mr. Nikhil. I have an Yaskawa SGDM 50 ADA Servo Motor and Drive on my machine. Its giving an error of encoder communication. Can you help change this Encoder? 🙏
Please tell me how to set in zero position of this encoder?
Hello did you find out how to do the zero position for encoder ?
Calibrate the encoder using a dual-beam oscilloscope. In short, the corresponding phase of the supply at the first input of the oscilloscope,
and on the second - Z. This is if you did not mix up the phases and the shaft did not move much, otherwise you need to turn 120 degrees and catch the approximate position to find the correspondence of the encoder phases with the motor phases.
Then, using a drill (not quickly), turn the rotor and precisely install the encoder.
Two signals with a phase shift of 90 degrees must coincide.
I'm writing from memory, maybe I'm a little wrong. If necessary - I will find the records - I will clarify.
Sorry for my language - I am writing through a translator.
Bay maayong adlaw naa kuy problema sa kong alaga, na machine bay servo motor japon halos dumogo na ang utak kuh sa kaka troubleshoot ginawa kuna rin ang mga nakalagay s manual nya peru wala parin ang problema bay wala akong pamali na amplifier at wala din akong servo motor na spare din. Kaya hirap na hirap ako bay
Which country. Please tell me your language. I am in India.
Philippines
Bay pwede bah tikaw ma friend sa FB bay video call sana kita ipakita nako nimo ang error sa machine na problema nako bay
Taga asa mo sir?
Taga Cebu
wala na ni calibration? dagan pud sir?
yup working ra
Thankyou for your help, but your sloppy work ethic is insulting to our trade
Servo motor 750w jaam hone ke Karan
Maybe you don't need it, but...
I saw two reasons for the jamming of the 750 W (Sigma1) motor.
1. Two wires to the motor (phase) are shorted - slows down. I had this in the socket.
2. We disassemble and clean the metal shavings on the rotor. Namely, it is on a magnet. We use plasticine, chewing gum, etc.
At the same time, it is undesirable for the stator to be without a rotor for a long time - it is desirable to insert at least a metal tube at that time, or (quickly clean the rotor and return it to its place).
I disassembled several pieces - they all spin. I did not put them on the machine, but I will calibrate them (encoder).
Sorry for the bad language (through the translator).
wrong way
This is the wrong way to draw the encoder.