Albrecht chuck service

แชร์
ฝัง
  • เผยแพร่เมื่อ 28 พ.ย. 2024

ความคิดเห็น • 80

  • @ROBRENZ
    @ROBRENZ 6 ปีที่แล้ว +11

    Nicely done Stan! Those chucks are available with wrench flats and a wrench for tightening the chucks more firmly and they make disassembly much easier since you can just grab the back half with the wrench.
    ATB, Robin

    • @zephyrold2478
      @zephyrold2478 6 ปีที่แล้ว

      Yes but he did it wrong, look at my link to how to do it : www.albrecht-germany.com/instruction/ pdf name : Reparaturanleitung_SBF_-_Stand_06.07.2016.pdf

    • @zephyrold2478
      @zephyrold2478 6 ปีที่แล้ว

      Sorry to point out that it is not the right way to do it, This is the way to do it right www.albrecht-germany.com/instruction/, look for Reparaturanleitungen SBF, pdf name : Reparaturanleitung_SBF_-_Stand_06.07.2016.pdf

    • @vincerodriguez209
      @vincerodriguez209 6 ปีที่แล้ว

      IF NOTHING ELSE STAn--you should feel great the amazing robrenz watches your videos----noone even close to him cept for this old tony--but for sure to different talents both incredible at what they do in thier own ways---- i think the most amazing thing would be if this old tony and robrenz colaberated ---tony has almost 500,00 subs and if rob got the shine--hias subs would go thru the roof---everyone should shout out rob to push his subs caUSE HE DONT DO ENOUGH VIDS!!!!!!!!!!!!! ENJOY ALL!!

  • @daveharriman2756
    @daveharriman2756 ปีที่แล้ว

    This is a great video, I just got one of these chucks, its touch and go if it works or not, now after seeing your vid, I dont feel scared taking it to bits and cleaning, thanks again Stan!

  • @BleuJurassic
    @BleuJurassic 6 ปีที่แล้ว +5

    The 'Missing' ball allows the bearings to turn without grinding against each other.
    I guarantee if you look closely in all bearing cups there is a space that is 1 to 1/2 the diameter of the bearing.

  • @raincoast2396
    @raincoast2396 6 ปีที่แล้ว +1

    Albrecht = High quality German engineering and machining. A top shelf chuck. Really good video Stan. Simple to the point.

  • @pierresgarage2687
    @pierresgarage2687 6 ปีที่แล้ว

    No missing bearing ball, that's the way they are... Had to "Unglue" mine from dried flood coolant, nothing would do it except a propane torch to soften the dried cake inside the slipping parts of the chuck. Works like a new one until next maintenance is required... Great chucks in deed.. ;)

  • @johnhall8455
    @johnhall8455 ปีที่แล้ว

    Nice video…
    I use copper strips to protect the body parts when unscrewing them….they can be extremely tight, especially if they’ve not been done since original assembly.
    The bearings should be that if they are all touching, another one would not fit in the remaining gap.
    They are all the same size, not as mentioned by someone earlier.
    The only lubrication required is on the bearings…I use a light waterproof grease. No other parts need lubricating, as it-will just act as a magnet to dust and chips, it will also prevent proper operation of the chuck…
    With frequent use, coolant can obviously enter into the internal parts of the chuck, this is why they should be disassembled and cleaned at regular intervals..

  • @marcmckenzie5110
    @marcmckenzie5110 4 ปีที่แล้ว

    Stan, I lost your website months ago and with my chemo-brain addled memory couldn’t find you again. Great segment!

  • @Elektronaut
    @Elektronaut 6 ปีที่แล้ว

    The last video I watched before I left for holidays was this one and I totally forgot about it.
    On holidays I went to a flea market and bought a Röhm and an Albrech chuck.
    I came back to this browser window still open. Now I'm watching it again :D

  • @RightOnJonCrane
    @RightOnJonCrane 4 ปีที่แล้ว

    Great Video Stan! Nice tip on setting those ball bearings in there with that piece inserted in the middle. Makes it a lot easier 💪✨👏👌🏻

  • @stephen7334
    @stephen7334 6 ปีที่แล้ว +1

    Very fussy doing it the first time, but once you get it apart it all makes sense. Totally agree on the fit and finish- such beautiful parts.

  • @johnleake708
    @johnleake708 6 ปีที่แล้ว +1

    Thanks for giving us the "inside scoop" on the Albrecht, I have one and love it, best thing I ever did for my 40+ year old 6+6 Rockwell Drill Press

  • @readysetsleep
    @readysetsleep 3 ปีที่แล้ว

    4:30 The rubber trick really saves the day!
    Just opened up an Albrecht Chuck with the rubber insert, no marring the knurling at all.
    Seriously that internal lube must be a wax based, the same kind from old bicycle hubs.

  • @terrycannon570
    @terrycannon570 6 ปีที่แล้ว +1

    Stan I see you still have a rare steel garbage can. I have one and even have the lid. When I was younger I guess I did not realize how heavy an empty one is. Mine is pretty heavy even empty. Maybe I should will it to the Smithsonian . LOL Thanks for the video great presentation.

  • @MaturePatriot
    @MaturePatriot 6 ปีที่แล้ว

    Great maintenance video. Almost all types of grease will gum over time. Especially with a lot of heating cooling cycles. Great Edutainment!!

  • @jerrycoleman2610
    @jerrycoleman2610 6 ปีที่แล้ว

    Stan, Very enjoyable video, thanks for sharing.!.!.!

  • @denniswilliams8747
    @denniswilliams8747 6 ปีที่แล้ว +1

    Thank you for the chuck maintenance vid.
    Jacobs chucks need similar maintenance too.
    Thanks for the vids

  • @bartonius1063
    @bartonius1063 6 ปีที่แล้ว

    Thanks! Mine was impossible to tighten or loosen, I followed your instructions and it works perfect now. Mine was in storage for 20yrs and had gummed up grease in it as well.

  • @joepie221
    @joepie221 6 ปีที่แล้ว +3

    Glad to see all is well. Just for reference, when I take one of these apart, I hold the smooth part of the chuck in my 3 jaw chuck on the lathe and use a strap wrench on the knurled part. It comes apart very easy that way. Just make sure the 3 jaw chuck jaws are grabbing the smooth part of the chuck and not the split collar. Good video.

  • @k5at
    @k5at 6 ปีที่แล้ว +1

    Thanks for sharing, I'll have to check my Albrect to see if I have the same problem. I bought it used, and have only used it a few times.

  • @furbarator
    @furbarator 6 ปีที่แล้ว

    Excellent tutorial, thank you for taking the time to make it.

  • @nevetslleksah
    @nevetslleksah 6 ปีที่แล้ว

    Thanks for making the video. I have an Albrecht chuck with an integral R8 shank that I managed to use to chuck and drill with a large Silver & Demming drill. Drill got caught in the work, chuck cranked down on the drill shank and got so tight I had to resort to Channelock pliers to get the chuck loose. Now the chuck has about
    .020” runout in it. So I still have the chuck but it’s in the junk pile. Your video should help me take it apart to figure out what is screwed up about it and maybe repair or at least keep it for spare parts. Needless to say, I don’t use my new Albrecht chuck with my large S&D twist drills any more.

  • @drubradley8821
    @drubradley8821 6 ปีที่แล้ว +4

    I used to service the various chucks at a part time job I had... The balls may have two different sizes, typically only (0.0010") difference is size... every other ball is the larger diameter from the in between the smaller diameter balls... The larger diameter balls balls are the load bearing balls, and the smaller diameter balls are merely just to space the larger balls from touching one another and spalling from the counter rotation of two load bearing balls contact points... I do not know of your chuck, but worth checking the next time, you have it open... sometimes, the balls are color coded, shinny hard chrome look to a darker, but still very shinny chromed look, to allow a visual indicator of the stagger of load bearing balls to spacers balls..

    • @drubradley8821
      @drubradley8821 4 ปีที่แล้ว

      @6818015 Ah, I see... Glad to know that... for that brand of chuck. I had a couple chances to buy one for myself, but, quite costly. sure is nice stuff though..

    • @drubradley8821
      @drubradley8821 4 ปีที่แล้ว

      @6818015 If I come across one of that brand, for a fair price, absolutely, I will grab it. Adding to the collection of chucks, I already have, (not of this brand) but do want to play with one in time.

  • @davep8462
    @davep8462 6 ปีที่แล้ว

    Thanks so much, I have a chuck that wont hold either. I really appreciate you spelling it out. I don't want to go at it with a bear pair of channel lock's but I'd rather not make a custom tool to disassemble either. Being a hobbyist, I don't have the luxury of apprenticeship, and all of the little details that matter. Like how to rough up the backs of the jaws - but not too much.

  • @DL5FS
    @DL5FS 6 ปีที่แล้ว

    Nice and informational videos !! i hope to meet you and all of the machinest at your Summer bash!! thank you

  • @patricksullivan9951
    @patricksullivan9951 6 ปีที่แล้ว +1

    Hi Stan, well it's amazing what a good cleaning can accomplish & repair!! nicely done!!

  • @joeblan9426
    @joeblan9426 6 ปีที่แล้ว +1

    Great Job Stan ,I would of lost some of the Bearings!

  • @jcs6347
    @jcs6347 6 ปีที่แล้ว

    Thanks Stan, I need to do this for one of my import clones, so it was timely and well presented.

  • @MCEngineeringInc
    @MCEngineeringInc 6 ปีที่แล้ว

    Great video! I’ve always wondered what was on the inside of one of those. Nice job.👍🏻

  • @ke6bnl
    @ke6bnl 6 ปีที่แล้ว

    Good job stan, I have an albrecht chuch that holds well but does not turn freely and will have to service it soon.

  • @larrychamberlain2871
    @larrychamberlain2871 6 ปีที่แล้ว +1

    Good Job, awaiting the next video

  • @MyShopNotes
    @MyShopNotes 6 ปีที่แล้ว +1

    Nice repair, thanks for the vid Stan.

  • @bertwacaser6719
    @bertwacaser6719 6 ปีที่แล้ว +1

    Thanks for the disassembly tips know I hope that my Rohm chuck will be as easy.

    • @duanedickey7043
      @duanedickey7043 6 ปีที่แล้ว +1

      Rohms are easier. At least the Spiro is. No replacements parts available though.

    • @bertwacaser6719
      @bertwacaser6719 6 ปีที่แล้ว +1

      Thanks I'll check it out.

    • @ellieprice3396
      @ellieprice3396 4 ปีที่แล้ว

      Great instructional video. My 0-1/2 Rohm appears to work the same as the Albrecht but much less expensive. It has spanner wrench holes in the body for extra tightening when used in reverse, such as backing out taps in the lathe chuck.

  • @kenzpenz
    @kenzpenz 6 ปีที่แล้ว +1

    Great video, aaaand we can see what you are doing.

  • @kendog4570
    @kendog4570 6 ปีที่แล้ว +5

    No lube on the threads , only on the balls and a slight bit on the inside of the hood. If the threads on the body and spindle are really worn or trashed the parts should be replaced. If they are shiny but not worn they should be lapped with medium valve grind paste in both push and pull directions, all paste fully removed, and the parts assembled and run dry. There should be no grease on the spindle or back surface of the jaw guide. Lube on there will give the jaws a spongy feel.

    • @RobertSzasz
      @RobertSzasz 6 ปีที่แล้ว +1

      kendog4570 if there is water based coolant being used wouldn't an extremely light oil provide some protection?

    • @kendog4570
      @kendog4570 6 ปีที่แล้ว +1

      I dont know. I got my info from Ed Schmidt at Albrecht Inc in New York in the early 1990's, via Guy Lataurd. The lapping is supposed to be part of the deluxe refurbish service. I have done it to several with good results. They might be able to give info on the effect of water based coolants on their chucks.

  • @StreuB1
    @StreuB1 6 ปีที่แล้ว

    Excellent video, Stan. Thanks so much!!

  • @bcbloc02
    @bcbloc02 6 ปีที่แล้ว +4

    I think the missing ball is standard fair.

  • @bid6413
    @bid6413 6 ปีที่แล้ว

    Stan, Very helpful. Thank you.

  • @GaryGrumble
    @GaryGrumble 6 ปีที่แล้ว

    Tom Lipton has a video on Albrecht tear down. His chuck had about 1/3 to 1/2 a ball spacing in the race. Yours looks like over 1 ball spacing. You may be missing a ball or this varies by chuck size.

  • @moeszyslack4676
    @moeszyslack4676 6 ปีที่แล้ว

    Great video Stan. Do one on a 14N, I think mine could use some maintenance.

  • @mikenixon9164
    @mikenixon9164 6 ปีที่แล้ว +2

    Thanks for sharing

  • @josephwilson6651
    @josephwilson6651 6 ปีที่แล้ว

    Another lesson learned Thank you for this video.

  • @dougiefroghopper7567
    @dougiefroghopper7567 6 ปีที่แล้ว +3

    Great use of tupperware.

    • @kenzpenz
      @kenzpenz 6 ปีที่แล้ว

      Yeah, sure hope you rinsed it out well, so the wife doesn't bust you. That solvent after taste is hard to deny.

  • @phrozenwun
    @phrozenwun 6 ปีที่แล้ว +1

    Enjoyed the video, just one note: the cleaning process can cause the appearance of cracks ;-)

  • @brucekoehler276
    @brucekoehler276 6 ปีที่แล้ว +1

    Wonderful

  • @duobob
    @duobob 6 ปีที่แล้ว +2

    This set of Albrecht repair instructions is even better than those by Albrecht:
    www.machinistblog.com/rebuilding-an-albrecht-drill-chuck/
    Yes, one ball is missing. Too much oil in there. The bearings, yes, grease. The coarse square threaded spindle and the nut it screws into should be dead dry. The hood can have a couple drops of oil spread over the entire surface. A drop or two of oil on the hood threads. That's it, to do it correctly. Stan, yours will likely work fine. If not, redo the lube.

    • @ShadonHKW
      @ShadonHKW  6 ปีที่แล้ว +1

      That's a great article Bob, in other news my chuck is working great and its only a matter of time till that 10W oil works its way out of there :)

    • @nowayjerk8064
      @nowayjerk8064 6 ปีที่แล้ว

      mine on my walker turner gets the oil down it every day and pukes it out to keep the rest of the table rust free dry steal = rust !!!!

  • @ls2005019227
    @ls2005019227 6 ปีที่แล้ว +1

    Nice repair! I've watched Tom's disassembly vid some time back, but this was a great refresher. My Albrecht style seems to slip (on a tap) while attempting to tap with the mill; is this common or does it need the disassembly/cleaning tune-up?

    • @ShadonHKW
      @ShadonHKW  6 ปีที่แล้ว +2

      These really rely on the friction between the drum and jaws to create the "cam" effect, heavy lube will reduce this effect.

  • @sharkrivermachine
    @sharkrivermachine 6 ปีที่แล้ว +1

    Very interesting.

  • @PeterWMeek
    @PeterWMeek 6 ปีที่แล้ว

    Look for [ bead tweezers ]; they have a little pocket in the tips to keep the balls from squeezing out. Excellent for manipulating small balls (or beads). Sometimes called pearl tweezers.

  • @craigs5212
    @craigs5212 6 ปีที่แล้ว +1

    Nice video, had to do my chuck a couple weeks ago. If you get a chance measure the run out on the BP. Would like to know what you see compared to my BP with an Albrecht.
    Craig

    • @TheOpinionationer
      @TheOpinionationer 6 ปีที่แล้ว +1

      Stan did a video some years ago, in which he re-ground the spindle in his mill using a rather simple technique. The run-out was much better after that if i remember. I would like to see what the chuck tir is too.

  • @baggd65
    @baggd65 6 ปีที่แล้ว

    I needed this video. Thanks.

  • @RGSABloke
    @RGSABloke 4 ปีที่แล้ว

    Hi STAN, the same thing is happening to my new Albrecht chuck. After a week working on it I found using a pair of sticky rubber glove to close the chuck does the business. Interested to hear your thoughts? Kindest regards. Joe.

  • @shiro-r4m
    @shiro-r4m 6 ปีที่แล้ว

    Nice chuck but the glorious ass crack had me distracted

  • @AtelierDBurgoyne
    @AtelierDBurgoyne 6 ปีที่แล้ว +3

    Nice job. Oxtools also has an excellent video on an Albrecht chuck tune-up.

    • @zephyrold2478
      @zephyrold2478 6 ปีที่แล้ว

      Yes but he did wrong, no oil on screw, look at this link www.albrecht-germany.com/instruction/ pdf name : Reparaturanleitung_SBF_-_Stand_06.07.2016.pdf

    • @zephyrold2478
      @zephyrold2478 6 ปีที่แล้ว

      No, Oxtools did it wrong, This is the way to do it right www.albrecht-germany.com/instruction/, look for Reparaturanleitungen SBF, pdf name : Reparaturanleitung_SBF_-_Stand_06.07.2016.pdf

  • @steven.h0629
    @steven.h0629 4 หลายเดือนก่อน

    Nice 👍😎✊

  • @sstorholm
    @sstorholm 6 ปีที่แล้ว

    What's the brand of that black oil can? Looks like a Goldenrod but I've never seen a black one.

    • @ShadonHKW
      @ShadonHKW  6 ปีที่แล้ว

      Not sure, I get them from NAPA auto parts.

  • @daveanderson2316
    @daveanderson2316 6 ปีที่แล้ว

    He said "hold those balls"... Yes I'm a child...

  • @ll6261
    @ll6261 3 ปีที่แล้ว

    Bevor du Videos drehs kannst du die Bude aufräumen.

  • @johndarakashiko9011
    @johndarakashiko9011 6 ปีที่แล้ว

    At 10:43 I like your Tshirt, is it moth attacks on your belly ... :)

  • @11zekim
    @11zekim 6 ปีที่แล้ว

    Good save. Here's a test: clamp a smooth HSS tool shank in the vise, then tighten the Albrecht down onto it with both hands. Then, see if you can spin the chuck on the shank with the same hands. If you can, jaws are worn; should be rebuilt.