Shortcut para sa inyo mga kaadik😅! 2:46 P0 - TYRE SIZE 4:09 P1 - CONTROLLER CUTOFF VOLTAGE 7:40 P2 - KPH or MPH 8:25 P3 - START MODE 10:15 P4 - CRUISE MODE 12:30 P5 - ACCELERATION 13:30 TIPS&ADVICE para sa speedometer at battery indicator! Salamat mga kaadik!😅
Hi. How About sa P6 sir, para san kaya yon? Yung brand kasi ng scooter ko is Red Wing, same throttle din sa inyo which is N-JAX, meron sya til P6. I tried yung P0 to P5 ok naman sya, same settings.
Syangapala sir, ask ko na din, when I set yung P0 into 8 which is my tire diameter, yung speed ng scooter ko nag-increase in terms of numbers, but not the actually speed na takbo mismo ng scooter. Before max speed ni scooter was 25kph, then naging 40+ kph na sya.
@@frankvillasor7341 gumamit ka ng gps un sa phone application. Mas accurate mga ganun. Then adjust adjust k n lng po sa Tyre Size(P0). Gang makuha mo un tama. Speedometer ung pangalan nun app na gamit ko. Color green.
Nagbabalak palang tlga ako bumili ng electric scooter kaya madalas ako mag research about electric scooter . kung ano ang maganda? matibay ? at pano gamitin? . Kaya matsala sa video na to at kay KA ADIK 😁 kahit papano my mga idea 💡 nako how to use electric scooter 🛴 👏🔥 Goodjob 👍🏻❗ more power & continue vlogging sana madami kapang ma share about electric scooter 🛴 Godbless🙏☺️
Goodday kaadik! Maramiing salamat din po.. Advice ko lng po sayo is, mas maige kung un mga high end ang bibilihin mo. Itong akin kase is generic lng. Drive safe pag nakabili ka na. Bili k rin ng mga protective gears mo. Thank you for watching!
Hello friend. Please can you help, O have just got my brand new scooter, its Honeywhale E5, pretty much exactly the same as the one in your video. I was playing around with the settings and nir my scooter wint accelerate properly, when I push the lever to go, it races forward then stops. I don't know what I've done or how to fix it back to the factory settings. Please can you help
I can’t find any fucking info in this scooter Im having the same problem you are. The honeywhale e5 is alright but My back wheel hit something around an hour ago and would kick for a second and then stop. When I pressed both of the buttons my scooter restarted and I had to shake the handlebars forward and back before it finally started working again. I have no idea what happened but I hope this helps
Goodday! How are you? Low Voltage Protection is like a voltage cutoff. For example: You have a 48volts scooter. And you set your scooter's low voltage protection at 43volt. When the battery volts drops below 43volts, your scooter will shutdown. You can only turn it on when the voltage(43v) has resumed or higher than the set Low Voltage Protection(43volts upwards) Low Voltage Protection will protect the battery from getting totally depleted and also prevents the motor from running with under voltage. Tahnk you for watching! Drive safe!
sir asko ko na dn po , ung sa p setting ung p0 ung sa tire size tamang tama po ba un na iset sa 5 ung tire size dun bsta ang mismong gulong ay 10inches tire ? salamat po para maging accurate ung speed nya sa throttle?
@@Eriane199RoBloX gumamit k ng GPS Speedometer then subukan mo habang nakasakay ka sa scooter mo. ikumpara mo un GPS SPEEDOMETER jan sa controller(throttle) mo. Kapag maxadong mataas un calculation ng controller mo, bawasan mo nmn un tyre size sa P0. Nka depende kase un speedometer sa Tyre size[(P0)NJAX-T throttle controller].
jayson ulanday hndi po tau prehas sir eh., cge sir adjust ajust cguro dpat gwin ko sa tire size ksi gnwa ko dng 5 mxado nman sya mababa sa throttle hehehe nung ngtry ako
Goodday kaadik! Ang strange nmn yan. May manual b yan scooter mo. Try mo po magpunta dun sa pinagbilihan mo, baka alam nila kung paano. Pacnca n late reply. Ride safe🤟
Boss ask ko lang sabi kasi ng pinagbilhan ko 40mm na daw magnet count niya pero sa psetting naka set lang sa 30 pwede kaya iset to 40 yung magnet count sa psetting?
Sir I have x thunder and its 48v1200w I'm confused about P1 settings ?? When I press it was 32.0 full battery And when I tried to put on 48v its showing low battery
Sir, if 48v ang scooter mo DONT set your voltage (p1 setting) to 48v. The controller will think low batt na ang scooter mo. Set mo sya at a lower voltage Between 40v to 43v. Then kapag bumaba ng ganun voltage ang battery mo dun pa lang sya magshut off.. Hope this helps..
@@jaysonulanday dagdag tip lang sir para sa mga nagtatanong about sa cut-off voltage ng battery,, each cell is 3.7v.. sa 48v battery may total yan na 13 cells (13 x 3.7v = 48.1v).. recommendation is dont let each cell drop below 3.07v.. so safest and lowest recommendation for a 48v battery cut-off voltage is 40v that will leave 3.07v per cell ( 40v÷13 cells = 3.07v) Para naman sa 52v battery (14 cells).. cut off should be 43v (43v ÷ 14 cells = 3.07) Ride safe :)
Good day sir ask klang po bat po bigla namamatay ung sakin, After ko gawin tong setting nyo po, Same lng po NJAX-T after ilang kilo, Namamatay sya kusa? Any advice?
Hello ask ko lang po boss ung e10 scooter bigla2 na lang nag sstop minsan napapansin ko nangyayare ung ganon pag sabay mong ibbreak ano po bang dapat gawin or may settings ba need gawin. Thank you in advance.
Goodday bro! Sorry for the late reply.. Basically it depends on the user if what setting is more convenient. This vid is just an explanation about the P-Settings of NJAX-T throttle. Thank you for watching😃
Boss good day tanong lng po ano ba dahilan kung bakit yung speedo meter ng e10 ko may exclamatory lumalabas pag pinatay ko yumg key tapos on ng wawarning sign siya salamat..
Goodday kaadik! Pacnxa na late response. Honestly, hindi ko pa na encounter yan ganyan. Usually kase pag may exclamatory un ung brake sensor. Di aandar un scooter. Pede mo rin ipakita yan dun sa pinagbilihan mo. Have a great day kaadik!
Idol pag ba sinabing 40km/h bilis niya,same din kaya ang bilis niya sa ibang scooter na ganyan din ang takbo?kasi ung sa amin mabilis ung gamit ko pero same 40km takbo pero parang mahina ung sa kanya bumwobwelo pa
Goodday kaadik! Un voltage setting po is para sa safety nun battery at motor. Bale yan po un cutoff voltage(low voltage protection) set mo po ng between 40-43v. Once na bumaba sa naka set na voltage un battery, automatic mag sha shut down un scooter. Mag tuturn off lng ulit once na charge or higher na sa naka set na cutoff voltage. Note: may mga battery kase na kapag totally drained.. mahirap ng i revive kaya nasisisra. May mga motor din na may certain voltage para gumana ng naaayon. Kaya importante po un voltage mai set ng tama. Set mo po between 40-43v. Drive safe!🤟 Maraming salamat po😀
5:36 i would like to understand the the low voltage proction. Today my e-scooter shut down when i was going at work. The battery was at 41/54. Can you please help me to understand how the low voltage protection works?
Goodday bro..! Low Voltage Protection is the lowest level voltage which is "set" related to the battery. For example: If you set your scooter's low voltage protection(p-setting) at 43volts. Once the battery voltage drops below 43volt , your scooter will shutdown automatically. Because you set the low voltage protection(cutoff) at 43v. Low Voltage Protection is very important for the battery and the motor. It protects the battery from getting totally depleted that may quickly reduce the lifespan of the battery. And it will protect the motor running from under voltage.
@@jaysonulanday thank you so much my friend 🙏🏽🙏🏽🙏🏽 Last question... #So i have to use the scooter voltage from 54.4V to 40V and after that i need to recharge it right? Sorry for my stupids questions but i don't understand nothing about e-scooter
@@The_Modern_Gladiatoryes, you can use your scoot from 54v down to 40v. That will be your battery level tracker. Don't depend on the battery indicator that you see from the LCD, it's not reliable. Hehhe! It's alright bro. Even me, i don't know anything about scooter when i first had it hehhe! Thank you so much too! Drive safe!😀🤟
Paps paano yung skin , naisaksak ko sya sa ibang e-10 na ang throttle nya is Lixivae ata yun .. tapos nawala yung kickstat ko sa P3-at cruise mode sa P4 . Kahet naka settings sya ng gnun . Ano dapat gawin ?
Goodday kaadik! Pacnxa na late reply. Search ko yan kung paano ayusin.. Balikan kita pag nalaman ko na. Pag sakaling malaman mo ahead of time, inform mo rin ako. Salamat paps! Drive safe kaadik..!
Ask ko lng kaadik.bkt ung scooter ko nka set lng xa sa p3 pgpindot q ung botton ung 55 nging 60.tpos nwla ung mga bar nya isa nlng ntira ayw ng bumalik ung ibng bar.atska gang p1 p2 p3 lng xq kaadik.
@@jaysonulanday hindi ser gsto ko sundin ung payo mo sa tutoryal mo sa pag baba ng voltage kaso ung blog u pla ay sa single motor paano kung gawin ko po sa dual motor parehas lamg ba yown? all the way dubai ser marami kang fans dto thank you!
@@jaysonulanday try ko kais to nun iniiba ko settings nun ginawa ko 52volts settings bumaba battery which is dko alam kung full bar ko ba nabili kasi kakabili ko lamg nun napanuod ko ung vlog mo tapos sabi nun seller full daw pero nun nag 52volts settings ako bumaba pero binalik kon sa turo mo 43 volts napuno pati ung settings mo na don malalaman kung ilan na batt po hindi sa gauge kung di sa voltage meter nya
Goodday kaadik! Maraming salamat po sa support. Pacnxa n late reply. Kung 48v un scooter mo, ok n ok po na sundan mo un volatge settinga ko. Un low voltage protection(cutoff voltage)pre, bale un ang magiging basehan ng controller mo, kung hanggang saan kababa un voltage ng battery para umandar un scooter. Kunware ang scooter mo is 52v,..tapos i set mo ito ng 52v din. Mamamatay agad un scooter mo pag below 52v n un battery.. kase nka set sa 52v un low voltage protection(cutoff voltage). Kung ano man un naka set, un ang susundin nun controller. Kung i set mo sa 48v(cutoff voltage) Mamamatay din un scooter mo pag reach ng below 48v. -automatic shutdown Magturn-on lng pag nai charge na or more than sa kung ano un naka set sa low voltage protection(cutoff voltage)
Boss bakit habang umaandar X thunder ko then nag break ako ayaw gumana agad ng Accelerator need pa totrally huminto or itaktak gulong sa harap para gumana ang accelator. Basta lagi yan pag mabilis takbo ko at nag break ako ayaw kumuha ng accelator after. Help Idol pleaseeee.....
Maraming salamat sir kc feeling ko ang bilis ng setting nung scooter ko kc 2nd ko na sya nabili kya malaking help po ung video tutorial mo sir at nagrereply ka po tlaga salamat po sa effort yung iba po kc d nagrereply keep safe din po lagi sa ride sir!
ka adik yung battery ng e10 ko dati umaabot sa 40v hindi pa rin nalolobat, ngayon nasa 43-44v (dalawang bar) namamatay na, mga 1 year and 5 months ko na gamit, 48v 13ah battery nya. normal ba yun? o pwede ko palitan yung settings sa controller cutoff voltage?
Goodday kaadik! Check mo un setting ng cutoff voltage mo. Baka nakaset sa 43v. Mamamatay tlga ng kusa yan pag naka set sa 43v. Pero mas ok kung ganyan(43v cutoff voltage) kaadik para di maxado madrain un battery. Masama din kase sa battery pag maxadong drain or depleted. Ride safe kaadik!🤟
Hello i have E20 scooter it shuts down all of a sudden ... I think when its low bay and the p-setting need to be fixed ... I didn't understand your language English only
Goodday bro! Sorry for the late reply. Try to change the volatre setting. If your scooter is 48v, then set the voltage cutoff between 40-43v. Drive safe!
@@DiscoveryEmad voltage cutoff- is the Lowest limit of your scooter battery voltage which is set in the throttle(p-settings). For example: if youre scooter is 48v, usually set the voltage between 40-43v. Once the battery drops below the value you set. Your scooter will automatically shutdown. And you can turn it on again when the voltage is higher(charging) than the set cutoff voltage.
Will It be possible to limit a scooter to 25km/h in the p setting? Everybody is talking about how tot increase but i want to turn the speed down of my kirin M4 pro
Goodday bro! Yes, its possible. If you're throttle is MR-100. (May apply to other trigger throttle). Go to P-15, then set the speed from 10-100. Set at 100, then your scooter will run at 100% speed. If set at 50, then your scooter will run 50% speed. Ride safe🤟
@@nathaliabriellemacatangay5961 maam parihas tau ng throttle sa e10 ko.. paano ba ang settings mo.. baka pwd maka hingi ng idea.. sa akin kasi napansin ko kahit fully charged pag pinipiga ko ung throttle minsan may lumabas sa display na triangle na kulay red. pero nawawala rin naman kaagad.. ewan ko kung ano un..
Джейсон привет!!! лайк и подписка и спасибо за видео! я тоже приобрёл самокат с таким компьютером! Я с Украины у нас таких нет ! Я так понял с таким компьютером идёт для Америки а для европы визуально похож а меню другое
Goodday kaadik! Nun nagtanong ako sa courier, sabi pede nmn ipadala(sea cargo). ihiwalay lng daw un battery. Di ko n natanong kung mgkano. Maraming salamat sa panonood😃
Goodday! Andito ka po ba sa abu dhabi? Sali k po sa group ng E10 club dito sa abu dhabi. Marami sa knila marunong mag set up. Nag se set up din ako pero di p ko ganun karunong. Thank you for watching!...
Idol Jayson taga Auh din ako idol..bkt ung e10 na nbili ko 2020..wla ung setting na P1 para maadjust ko sana ung voltage idol?bkt P03 na sya agad at pili ka 24,36 at 48volts lang option ko agad...kya nung ng 43 volt ako matic dna umander nag error 5 na at undervoltage protection na lumalabas...inakay ko scoot ko Al wahda to khalidiya...sana m2lungon mo ako idol...d2 kc sa content mo naadjust mo ung voltage eh...new subscriber idol..more power to ur channel...😊
Goodday kaadik! Nakabili k n pla ng scooter mo. Congrats!🤟 May mga ganyan na nangyayare eh. Di ma-access un P-Settings. Nai patingin mo n ba yan sa pinagbilihan mo?
Good day sir pasagot naman po ako baka may idea kau.. bumili ako ng e10 kagabi pero iba ung throttle nya hindi kagaya nito.. tapos wala pang manual sa box.. baka pwd pasuyo sir ito ung available na P settings nya. P - 3 P - 6 P - 7 P - 9 P - 15 P - 16 P - 99 tapos bro napansin ko kahit full charged maman ung battery pag pinipiga ko ung throttle minsan may lumalabas na warning sign triangle na red tapos nawawala rin kaagad.
Hi Jason, I hope your ok. Can you help me with something please? When I go into the P settings on my scooter, which is a 48V , scooter 600W on P setting 1 which is the battery voltage I am unable to bring the number up to 48, the highest number I can get to is 28.4, If I continue to try and up the voltage I get the empty flashing battery like what you got on your video. Can you tell me why you think is happening?
Sir.. may tanong lang ako kasi bumili ako ng E10 scooter nung friday unang gamit napansin ko sa kalagitnaan ng takbo humhinto na sya di na gumagana accelerator nya at ayaw ng tumakbo.. pinapalitan ko kahapon ginamit ko yung bagong palit na unit tpos same parin naging prob biglang huminto.. factory defect b sya? Same problem lng din.. sana matulungan mo ako sa prob ng scooter ko gusto kong papalitan ngayin ng ibang model nlng
Goodday kaadik! Un isang bilihan ng scoot dito sa abu dhabi sinasabi nga na nagkkaproblema un mga bagong unit ng E10. Kung maibabalik mo p yan gamit un warranty, mas maige n magpalit k n lng ng unit. Di na kase maganda un mga bagong E10 ngayon.
Ka scoot good day sinet ko ng 43 ang P1 settings ko, pero bakit po kaya hindi nacut or nashutdown ang power voltage ko 40 na lang sya pero natakbo pa din although sobrang bagal po sya, chinarge ko na din for assurance hehe.
Goodday kaadik! Dati nasa 38kph lng(gps speedometer) Ang bigat n kse ni unggoy dahil sa mga accessories lalo n un acrylic board at battery. After ko palitan un controller nasa 41kph na Check mo un "Drive Test" na latest upload ko pre. Have a nice day pre🤟.
Hello bro hope you doing well I have e5 same setting can I set my voltage to 70 from 43 And Also my tyre diameter was 6or 7 I think I changed to 10 is that ok? The tyre on scooter is 10inch
goodday bro! Sorry for the late reply. If ur scooter voltage is 48, set ur cutoff(low voltage protection) at 43v. The tyre size will affect the speedometer calcultation. It has nothing to do with the speed. To get accurate speed calculation, use GPS Speedometer. Then match ur throttle controller speedometer by adjusting the tyre size until you get the right value that matches sa GPS Speedometer. You can download from your android fone. SPEEDOMETER app. Thank you for watching! Drive safe!
Goodday kaadik! Kung same lng po tyo ng throttle..possible po na pareho lang. Generic kase ang E10, magkakaiba un throttle. Ride safe!araming salamat po
@@donvalladolid4996 parang may dati ng nagtanong sakin niyan "p0-06" din. As long as ok nmn un performance ng scoot mo. Ok lng yan. Ok po, shout out po kita. Maraming salamat po sa support kaadik!😀🤟
Shortcut para sa inyo mga kaadik😅!
2:46 P0 - TYRE SIZE
4:09 P1 - CONTROLLER CUTOFF VOLTAGE
7:40 P2 - KPH or MPH
8:25 P3 - START MODE
10:15 P4 - CRUISE MODE
12:30 P5 - ACCELERATION
13:30 TIPS&ADVICE para sa speedometer at battery indicator!
Salamat mga kaadik!😅
Hi. How About sa P6 sir, para san kaya yon? Yung brand kasi ng scooter ko is Red Wing, same throttle din sa inyo which is N-JAX, meron sya til P6. I tried yung P0 to P5 ok naman sya, same settings.
@@frankvillasor7341 goodday kaadik!
i sesearch ko po yan.. pag nalaman ko n po, i'll get back to you..
Thank you for watching!
Drive safe!
@@jaysonulanday Thanks for the reply. Sige sige please let me know. Thanks!
Syangapala sir, ask ko na din, when I set yung P0 into 8 which is my tire diameter, yung speed ng scooter ko nag-increase in terms of numbers, but not the actually speed na takbo mismo ng scooter. Before max speed ni scooter was 25kph, then naging 40+ kph na sya.
@@frankvillasor7341 gumamit ka ng gps un sa phone application.
Mas accurate mga ganun. Then adjust adjust k n lng po sa Tyre Size(P0). Gang makuha mo un tama.
Speedometer ung pangalan nun app na gamit ko. Color green.
Wala talaga kong balak mag subscribe dahil sa "kaadik" na tawag pero na-kombinsi din ako dahil sa linaw at scope ng content. Good job sir!
Magandang araw sayo kaaaaa......hehehe!
Na adik na po kase ako kaka youtube kaya un na ginamit kong line hehe!
Maraming salamat po😀
Hello, does this model work as an alternative to the NJ-AOXIONG hb02 study? I hope to respond.
I have same Scoty njaxt accelerated not working no error showing can u help me
Goodday bro..
What is the problen with your scoot?
Nagbabalak palang tlga
ako bumili ng electric scooter kaya madalas ako mag research about electric scooter . kung ano ang maganda? matibay ? at pano gamitin? . Kaya matsala sa video na to at kay KA ADIK 😁 kahit papano my mga idea 💡 nako how to use electric scooter 🛴 👏🔥
Goodjob 👍🏻❗
more power & continue vlogging sana madami kapang ma share about electric scooter 🛴
Godbless🙏☺️
Goodday kaadik!
Maramiing salamat din po..
Advice ko lng po sayo is, mas maige kung un mga high end ang bibilihin mo. Itong akin kase is generic lng.
Drive safe pag nakabili ka na.
Bili k rin ng mga protective gears mo.
Thank you for watching!
New subscriber here master, salamat at malaking tulong ito sa aming mga newbie’s👌🏻
Maraming salamat din sa support kaadik!
Ride safe lage!🤟
Hello friend. Please can you help, O have just got my brand new scooter, its Honeywhale E5, pretty much exactly the same as the one in your video. I was playing around with the settings and nir my scooter wint accelerate properly, when I push the lever to go, it races forward then stops. I don't know what I've done or how to fix it back to the factory settings. Please can you help
I can’t find any fucking info in this scooter Im having the same problem you are. The honeywhale e5 is alright but My back wheel hit something around an hour ago and would kick for a second and then stop. When I pressed both of the buttons my scooter restarted and I had to shake the handlebars forward and back before it finally started working again. I have no idea what happened but I hope this helps
thank you boss laking tulong sa newbie na katulad ko salamat.
Goodday kaadik!
Maraming salamat din po..!
Drive safe!
very informative 🔥
Napaka laking tulong. Maraming salamat po😇
Goodday kaadik!
Maraming salamat din.
Ride safe palage🤟
very informative video.. helpful sa mga baguhan tulad namin :)
thanks and keep safe!
I have x thunder scooter 48v 1200w dual motor bt am not able to access the p settings. How do I solve the problem?
hi, i dont know how it work protection voltage ... can you helpme i have the CYCLONE SCOOTER GREENWAY
Goodday! How are you?
Low Voltage Protection is like a voltage cutoff.
For example:
You have a 48volts scooter. And you set your scooter's low voltage protection at 43volt. When the battery volts drops below 43volts, your scooter will shutdown. You can only turn it on when the voltage(43v) has resumed or higher than the set Low Voltage Protection(43volts upwards)
Low Voltage Protection will protect the battery from getting totally depleted and also prevents the motor from running with under voltage.
Tahnk you for watching!
Drive safe!
Hi great 👍 video!!
I have the same question,
52v 20ah lithium battery
2×1000w electric scooter
2×25A controllers.
What is the voltage cut?
Idol sana mapansin mo pareview nmn ng ax-hb20 controller pano mkpunta sa p settings😊😊😊😊😊
Nice 1 bro... Salamat at nagkaroon ako Idea pano iset-up scooter ko👊🙏
Goodday kaadik!
Salamat din po sa panonood..
@@jaysonulanday Welcome boss🙏Kapitbahay lang tyo.. DXB😁
Ikaw na ata napanood ko pinakamalinaw mag-explain🤭
Salamat kaadik sa info...same lng b indicator ng crony
Goodday kaadik!
As long as NJAX-T rin un throttle mo, parehas lng yan.
Maraming salamat din.
Ride safe lage🤟
good job sir sa pgturo po ng mga tamang mga p settings sa gantong scooter ty po 👍🏻👌🏻
Goodday! Salamat po sir😀
sir asko ko na dn po , ung sa p setting ung p0 ung sa tire size tamang tama po ba un na iset sa 5 ung tire size dun bsta ang mismong gulong ay 10inches tire ? salamat po para maging accurate ung speed nya sa throttle?
@@Eriane199RoBloX goodday! Same ba tayo ng throtle controller?
@@Eriane199RoBloX gumamit k ng GPS Speedometer then subukan mo habang nakasakay ka sa scooter mo. ikumpara mo un GPS SPEEDOMETER jan sa controller(throttle) mo.
Kapag maxadong mataas un calculation ng controller mo, bawasan mo nmn un tyre size sa P0.
Nka depende kase un speedometer sa Tyre size[(P0)NJAX-T throttle controller].
jayson ulanday hndi po tau prehas sir eh., cge sir adjust ajust cguro dpat gwin ko sa tire size ksi gnwa ko dng 5 mxado nman sya mababa sa throttle hehehe nung ngtry ako
Idol bakit ung battery indicator niya 1bar lng pero full charge na at ung volt nasa 52v naman na
Goodday kaadik!
Ano throttle mo?
@@jaysonulanday same po ng sau idol dto..
@@jaysonulanday ung battery bar lng ang hindi full
Po-p5 din ido
@@JayDoiTTV sinundan mo lahat un ginawa ko? Lalo n un voltage cutoff na 43v.
Thank you sir same abudhabi naging ok na din takbo ng buddy ko👌😅
Goodday kaadik!
Ride safe palage🤟
Maramung salamat din
Thank you lodi..i always support you lods!
Goodday kaadik!
Maraming salamat po sa support..!
Have a nice day po🤟😀
Boss...anong setting para sa xthunder 48 volts 1000 watts
Goodday kaadik!
Anong throttle ang gamit mo?
Happy New Year!
Hello sir jay ask ko lng bt ayw nung skn wla syang psetting
San po pwdng mkabili ng acelarator motor ng e10 elwctric scoter
Salamat paps nasolve din problema ko sa speedometer
Goodday kaadik!
You're welcome.
Ride safe palage🤟
Thanks bro ngayon ko lang nalaman to😂 subscribed!!
Goodday kaadik!
Maraming salamat po😃
@@jaysonulanday boss ung scooter ko na ganyang bigla nwla ung brake indicator saka Di na gumana ung speed meter ko panu ayusin slmat
boss ur video very helpful thanks bro
Goodday bro!
You're welcome.
Ride safe always..
Thank you too bro🤟
Boss bkt prang wlang p settings njax-t dual motor na my toys mt525? Ket gnawa ko ung tut mo
Paps naka njax-t ang mober md6 v2 ko bagong bili. Hindi ko mapasok yung P-settings kahit i hold ko yung dalawang button , salamat sa sagot 😇
Goodday kaadik!
Ang strange nmn yan. May manual b yan scooter mo.
Try mo po magpunta dun sa pinagbilihan mo, baka alam nila kung paano.
Pacnca n late reply.
Ride safe🤟
Boss ask ko lang sabi kasi ng pinagbilhan ko 40mm na daw magnet count niya pero sa psetting naka set lang sa 30 pwede kaya iset to 40 yung magnet count sa psetting?
Bro.tanong ko lng yung batt.ko 36v8mah,pwd ko ba sya palitan ng higher voltage kasi 3 days ko lng kasi siya magamit bahay trabaho lng..
Sir I have x thunder and its 48v1200w
I'm confused about P1 settings ?? When I press it was 32.0 full battery
And when I tried to put on 48v its showing low battery
Sir, if 48v ang scooter mo DONT set your voltage (p1 setting) to 48v. The controller will think low batt na ang scooter mo. Set mo sya at a lower voltage Between 40v to 43v. Then kapag bumaba ng ganun voltage ang battery mo dun pa lang sya magshut off.. Hope this helps..
@@pg9165
Goodday kaadik!
Salamat sa reply.. this really helps!
@@jaysonulanday dagdag tip lang sir para sa mga nagtatanong about sa cut-off voltage ng battery,, each cell is 3.7v.. sa 48v battery may total yan na 13 cells (13 x 3.7v = 48.1v).. recommendation is dont let each cell drop below 3.07v.. so safest and lowest recommendation for a 48v battery cut-off voltage is 40v that will leave 3.07v per cell ( 40v÷13 cells = 3.07v)
Para naman sa 52v battery (14 cells).. cut off should be 43v (43v ÷ 14 cells = 3.07)
Ride safe :)
@@pg9165
Maraming salamat kaadik!
makakatulong po ito ng lubos,..🤟😀
@@jaysonulanday youre welcome sir :)
sir pashoutout!! ., more power and continue vlogging about this electric scooter!! 👍🏻🛴👌🏻
Good day sir ask klang po bat po bigla namamatay ung sakin,
After ko gawin tong setting nyo po,
Same lng po NJAX-T after ilang kilo,
Namamatay sya kusa? Any advice?
Hello ask ko lang po boss ung e10 scooter bigla2 na lang nag sstop minsan napapansin ko nangyayare ung ganon pag sabay mong ibbreak ano po bang dapat gawin or may settings ba need gawin. Thank you in advance.
Idol pwede ba pala palitan tf-100 throotle at controler ?para sana hanggang p9
Hello my lights & horn won’t work please help
Goodday! Check the wirings. Or maybe you need to replace it.
how to u go to settings? holding power button and mode button doesnt work for me
boss pag na nagccharge ang escoot nd cra ang controller nd kc mabuhay ang throttle salamat
Goodday!
Pcnxa n late reply.
Maaring sira n un controller.
thank you sa sharing... more power
Goodday kaadik!
Thank you rin po for watching!
Bro.. Anong GPS Speedometer apps gamit mo..
Goodday kaadik!
"GPS Speedometer - Odometer App"
ung gamit ko.
May logo na 84MPH.
Ride safe lage kaadik!🤟
@@jaysonulanday Salamat bro. Sa jeddah kaba bro?!
@@junlizada2150 sa UAE ako kaadik.
Ride safe lage sa inyo jn.
Which setting is best according to you for a default normal e10 scooter without any modifications
Goodday bro!
Sorry for the late reply..
Basically it depends on the user if what setting is more convenient.
This vid is just an explanation about the P-Settings of NJAX-T throttle.
Thank you for watching😃
Boss good day tanong lng po ano ba dahilan kung bakit yung speedo meter ng e10 ko may exclamatory lumalabas pag pinatay ko yumg key tapos on ng wawarning sign siya salamat..
Pagkatapos kong na expose sa init
Goodday kaadik!
Pacnxa na late response.
Honestly, hindi ko pa na encounter yan ganyan.
Usually kase pag may exclamatory un ung brake sensor. Di aandar un scooter.
Pede mo rin ipakita yan dun sa pinagbilihan mo.
Have a great day kaadik!
Idol pag ba sinabing 40km/h bilis niya,same din kaya ang bilis niya sa ibang scooter na ganyan din ang takbo?kasi ung sa amin mabilis ung gamit ko pero same 40km takbo pero parang mahina ung sa kanya bumwobwelo pa
Boss if bawasan ung voltage ng scooter to 48v to 45v hindi b magkaprblema s scoot un
Goodday kaadik!
Un voltage setting po is para sa safety nun battery at motor.
Bale yan po un cutoff voltage(low voltage protection) set mo po ng between 40-43v.
Once na bumaba sa naka set na voltage un battery, automatic mag sha shut down un scooter. Mag tuturn off lng ulit once na charge or higher na sa naka set na cutoff voltage.
Note:
may mga battery kase na kapag totally drained.. mahirap ng i revive kaya nasisisra.
May mga motor din na may certain voltage para gumana ng naaayon.
Kaya importante po un voltage mai set ng tama.
Set mo po between 40-43v.
Drive safe!🤟
Maraming salamat po😀
5:36 i would like to understand the the low voltage proction. Today my e-scooter shut down when i was going at work. The battery was at 41/54. Can you please help me to understand how the low voltage protection works?
Goodday bro..!
Low Voltage Protection is the lowest level voltage which is "set" related to the battery.
For example: If you set your scooter's low voltage protection(p-setting) at 43volts. Once the battery voltage drops below 43volt , your scooter will shutdown automatically.
Because you set the low voltage protection(cutoff) at 43v.
Low Voltage Protection is very important for the battery and the motor.
It protects the battery from getting totally depleted that may quickly reduce the lifespan of the battery.
And it will protect the motor running from under voltage.
@@jaysonulanday thank you so much my friend 🙏🏽🙏🏽🙏🏽
Last question...
#So i have to use the scooter voltage from 54.4V to 40V and after that i need to recharge it right?
Sorry for my stupids questions but i don't understand nothing about e-scooter
@@The_Modern_Gladiatoryes, you can use your scoot from 54v down to 40v.
That will be your battery level tracker.
Don't depend on the battery indicator that you see from the LCD, it's not reliable.
Hehhe! It's alright bro. Even me, i don't know anything about scooter when i first had it hehhe!
Thank you so much too!
Drive safe!😀🤟
@@jaysonulanday thank you so much bro. I really appreciate your help. You doing a great work. Keep it up 💪🏽.
Have a great day 🤘🏼
@@The_Modern_Gladiator thank you too bro!drive safe!
Paps paano yung skin , naisaksak ko sya sa ibang e-10 na ang throttle nya is Lixivae ata yun .. tapos nawala yung kickstat ko sa P3-at cruise mode sa P4 . Kahet naka settings sya ng gnun . Ano dapat gawin ?
Goodday kaadik!
Pacnxa na late reply.
Search ko yan kung paano ayusin..
Balikan kita pag nalaman ko na.
Pag sakaling malaman mo ahead of time, inform mo rin ako.
Salamat paps!
Drive safe kaadik..!
Ask ko lng kaadik.bkt ung scooter ko nka set lng xa sa p3 pgpindot q ung botton ung 55 nging 60.tpos nwla ung mga bar nya isa nlng ntira ayw ng bumalik ung ibng bar.atska gang p1 p2 p3 lng xq kaadik.
Goodday kaadik!
Pacnxa na, na missed ko comment mo.
Ok n b scooter mo?
Pashout naman dyan tapos..alam muna yan...keep safe
Goodday! Ok po! Salamat po..
paano ser kung 52volts daw ung dual motor na xthunder pro na gamit ko ngaun kung 43volts healthy yon ser?
Goodday kaadik!
Hindi na ba naabot sa 52v pag fullcharge?
@@jaysonulanday hindi ser gsto ko sundin ung payo mo sa tutoryal mo sa pag baba ng voltage kaso ung blog u pla ay sa single motor paano kung gawin ko po sa dual motor parehas lamg ba yown? all the way dubai ser marami kang fans dto thank you!
@@jaysonulanday try ko kais to nun iniiba ko settings nun ginawa ko 52volts settings bumaba battery which is dko alam kung full bar ko ba nabili kasi kakabili ko lamg nun napanuod ko ung vlog mo tapos sabi nun seller full daw pero nun nag 52volts settings ako bumaba pero binalik kon sa turo mo 43 volts napuno pati ung settings mo na don malalaman kung ilan na batt po hindi sa gauge kung di sa voltage meter nya
Goodday kaadik!
Maraming salamat po sa support.
Pacnxa n late reply.
Kung 48v un scooter mo, ok n ok po na sundan mo un volatge settinga ko.
Un low voltage protection(cutoff voltage)pre, bale un ang magiging basehan ng controller mo, kung hanggang saan kababa un voltage ng battery para umandar un scooter.
Kunware ang scooter mo is 52v,..tapos i set mo ito ng 52v din.
Mamamatay agad un scooter mo pag below 52v n un battery.. kase nka set sa 52v un low voltage protection(cutoff voltage).
Kung ano man un naka set, un ang susundin nun controller.
Kung i set mo sa 48v(cutoff voltage)
Mamamatay din un scooter mo pag reach ng below 48v.
-automatic shutdown
Magturn-on lng pag nai charge na or more than sa kung ano un naka set sa low voltage protection(cutoff voltage)
@@jaysonulanday grabe maasahan to cge hindi pla basehan ung kung dual motor or single bsta voltage pag uusapan ayos!! approve ser salamat sayo!
Very informative sir
Goodday kaadik!
Maraming salamat sa panonood🤟
@@jaysonulanday new rider lng ako kaadik bumili ako ng e10 2021😁
Boss.. anu kaya setting trottle..PO to P6..G-FORCE
Sir.pede nba I charge pag 44v nlng?
Goodday kaadik!
Pacnxa na late reply..
Pedeng pede po.
Drive safe😀🤟
Boss bakit habang umaandar X thunder ko then nag break ako ayaw gumana agad ng Accelerator need pa totrally huminto or itaktak gulong sa harap para gumana ang accelator. Basta lagi yan pag mabilis takbo ko at nag break ako ayaw kumuha ng accelator after. Help Idol pleaseeee.....
Hi sir same lng po ng mober t10 ung p setting mode newbie lng po kc AU po yung throttle ng scooter ko then P0-P5 setting sya
Goodday kaadik!
Kung parehas po tyo ng throttle, sundan mo lng po un sa vid tutorial ko.
Ride safe!
Maraming salamat🤟
Maraming salamat sir kc feeling ko ang bilis ng setting nung scooter ko kc 2nd ko na sya nabili kya malaking help po ung video tutorial mo sir at nagrereply ka po tlaga salamat po sa effort yung iba po kc d nagrereply keep safe din po lagi sa ride sir!
Youre welcome po..
Drive safe lng palage🤟
So my scooter when is fully charged it will be on 52 voltage how can I stop it from shutting off
ka adik yung battery ng e10 ko dati umaabot sa 40v hindi pa rin nalolobat, ngayon nasa 43-44v (dalawang bar) namamatay na, mga 1 year and 5 months ko na gamit, 48v 13ah battery nya. normal ba yun? o pwede ko palitan yung settings sa controller cutoff voltage?
Goodday kaadik!
Check mo un setting ng cutoff voltage mo.
Baka nakaset sa 43v.
Mamamatay tlga ng kusa yan pag naka set sa 43v.
Pero mas ok kung ganyan(43v cutoff voltage) kaadik para di maxado madrain un battery.
Masama din kase sa battery pag maxadong drain or depleted.
Ride safe kaadik!🤟
@@jaysonulanday wala naman ako binago mula noon, minsan ba nababago yun ng kusa? Ty kaadik
Nice content keep it up godbless Thank you for sharing this nice idea. Keep vloging stay safe po...
48v 1000w ang sccot ko kaadik baka pwede po makahingi ng advice base on your expi
Goodday kaadik! Pacnxa na late reply.. na busy lang sa work.
Sana makatulong p ko sayo.
Ride safe🤟
NJAX-T po ung throttle ko..pero ayaw nya mag P-setting..anu po kya problem nya..
brother yung sa P settings ko 48v, 36v and 24v lang ang choices..ok lang iset to 24v?
Goodday kaadik!
Set mo sa 36v, maxado ng mababa un 24v.
Maraming salamat sa panonood🤟
Drive safe!
@@jaysonulanday thanks lods..keep it up.. 👍👍👍
@@MicoVlogs thank you rin po🤟
Can you please help me to reset al settings?
Which throttle do you have?
How's your scoot now?
@@jaysonulanday we have the same throttle
@@jaysonulanday it's fully charged 54.4V
@@The_Modern_Gladiator Is it functioning well?
Set the Low Voltage Protection at 40v or 43v.
Hello i have E20 scooter it shuts down all of a sudden ... I think when its low bay and the p-setting need to be fixed ... I didn't understand your language English only
Goodday bro!
Sorry for the late reply.
Try to change the volatre setting.
If your scooter is 48v, then set the voltage cutoff between 40-43v.
Drive safe!
i need explanation for P-voltage setting in English
@@DiscoveryEmad voltage cutoff- is the Lowest limit of your scooter battery voltage which is set in the throttle(p-settings).
For example: if youre scooter is 48v, usually set the voltage between 40-43v. Once the battery drops below the value you set. Your scooter will automatically shutdown.
And you can turn it on again when the voltage is higher(charging) than the set cutoff voltage.
@@jaysonulanday ok but mine shut down when its 3 pars atthe battery indicator and only turn on when its in charge again
@@DiscoveryEmad the battery indicator is not reliable.
You base the battery level from its voltage.
Have you check your voltage setting?
sir. ilang km bago malobat yan e10. my range test ka brow?
Magandang araw sayo kaadik!
Gagawan ko p lng ng range test to.
Pag nagawan ko n, send ko sayo un link..
😀
cge cge sir. para lam ko din kukunin ko . maramin salamat sir.
Salamat din po kaadik😀
dumating na akin sir san mo na buy yang throttle mo sir? n jax.
@@mheckpool stock n yan n throttle. Yan tlga ang nakasalpak nun binili ko.
Enjoy riding kaadik!
Drive safe ha..
Helmet
Protective gear
hi, is there also a hack sa njax-t on how to increase the top speed?
I have a p6 and what function is it?
Good day! Which throttle do you have?
@@jaysonulanday It's the same model I have.
(NJAX-T)
Let me find it out first then i'll get back to you.. but rest p-settings(p0-p5) are the same?
@@jaysonulanday Thank you very much.
Yes, it's the same.
Sir jx-168 throttle anu po settings newbiew lang sa escooter e salamats! And more power!
Lods applicable din ba to sa X thunder scooter? Info please
Goodday kaadik!
Pacnxa na late reply.
PM mo ko sa fb, then send ko dayo un copy ko ng mga P-Settings
Yes same lang sila na try ko na sa x thunder ko
Will It be possible to limit a scooter to 25km/h in the p setting? Everybody is talking about how tot increase but i want to turn the speed down of my kirin M4 pro
Goodday bro!
Yes, its possible.
If you're throttle is MR-100. (May apply to other trigger throttle).
Go to P-15, then set the speed from 10-100.
Set at 100, then your scooter will run at 100% speed.
If set at 50, then your scooter will run 50% speed.
Ride safe🤟
@@jaysonulanday thanks for the answer! Met range Will get better also ? And Will the maximum speed Will be adjusted for all the three P modes?
nice!!! sana meron review nung katulad ng sakin . ...haha...iba kasi controller nun sakin
Magandang araw sayo kaadik!
Anong tatak nun throttle controller mo?
Thank you for watching!😀
mr - 100 bro..., haha...sana makagawa ka din tutorial niyan...salamat... godbless more power
Ok po kaadik!😀
@@jaysonulanday salamat bro
@@nathaliabriellemacatangay5961 maam parihas tau ng throttle sa e10 ko.. paano ba ang settings mo.. baka pwd maka hingi ng idea.. sa akin kasi napansin ko kahit fully charged pag pinipiga ko ung throttle minsan may lumabas sa display na triangle na kulay red. pero nawawala rin naman kaagad.. ewan ko kung ano un..
Anung model ng skoter mo sir?
Goodday kaadik!
E10 un gamit ko. Generic na scooter.
2019.
Ride safe kaadik🤟
Sir baka pwde moko mahelp sa e10 pro.
Ganito din ba sa Mober T10?
Goodday kaadik!
Di ko lng po alam..
Check mo po un reviews sa yt.
Maraming salamat sa panonood
Джейсон привет!!! лайк и подписка и спасибо за видео! я тоже приобрёл самокат с таким компьютером! Я с Украины у нас таких нет ! Я так понял с таким компьютером идёт для Америки а для европы визуально похож а меню другое
I have the same controller. Wala ba talagang silbi yung battery indicator nito? Di kasi gumagana eh.
Goodday kaadik!
Pacnxa na po late reply .
Di po tama un battery indicator.
Mag base ka n lng po sa voltage.
Drive safe!
Maraming salamat po
Boss uae dn po ako balak ko bumili ng e.scooter pde ba i uwi ng pinas at ano possible na pdeng gawin durinh travel?
Goodday kaadik!
Nun nagtanong ako sa courier, sabi pede nmn ipadala(sea cargo).
ihiwalay lng daw un battery.
Di ko n natanong kung mgkano.
Maraming salamat sa panonood😃
kahit ba annh brand ng throttle pwede sa mober s10 v1 salamat
Goodday kaadik!
Hindi po.
Kelangan compatible un throttle at controller.
Tanong lang bro, kung magppaset up at mag aadd ako ng ilaw saan ako dapat magppagawa? Thanks
Goodday! Andito ka po ba sa abu dhabi? Sali k po sa group ng E10 club dito sa abu dhabi. Marami sa knila marunong mag set up.
Nag se set up din ako pero di p ko ganun karunong.
Thank you for watching!...
Aumento de potencia?
Paps yung p5 .....equivalent sa MR-100 throttle.. anung P Setting po sya?
Goodday kaadik!
PM mo ko sa fb.
Send ko sayo un mga settings.
Drive safe!
Maraming salamat po sa panonood😃
Its not getting into p sitting when i press both buttons. What is the solution?
Idol ilang volts ba bago mamatay ang battery? Nasa 53v sakin pag full charge e
Goodday kaadik!
Depende po sa naka set na cutoff voltage mo.
Drive safe!
Maraming salamat sa panonood🤟
@@jaysonulanday hindi naman sya hanggang 0 idol parang cellphone?
@@jaibsm31 Set mo un cutoff voltage ng between 40-43v.
Safe zone un pre
Boss pano b dagdagan ang speed
Goodday kaadik! Wala ng ibibilis pa.. sagad na po ung 40-45kph(depende sa bigat nun nagddrive).
Drive safe!
Maraming salamat..!
Bro my scooter not run please can u Tel me how to setting I have E10 please
Goodday bro!
What happen with your scooter? Did you touch the P-settings?
Idol Jayson taga Auh din ako idol..bkt ung e10 na nbili ko 2020..wla ung setting na P1 para maadjust ko sana ung voltage idol?bkt P03 na sya agad at pili ka 24,36 at 48volts lang option ko agad...kya nung ng 43 volt ako matic dna umander nag error 5 na at undervoltage protection na lumalabas...inakay ko scoot ko Al wahda to khalidiya...sana m2lungon mo ako idol...d2 kc sa content mo naadjust mo ung voltage eh...new subscriber idol..more power to ur channel...😊
Goodday kaadik! Cnxa na po late reply.. anong throttle controller gamit mo?
Boss san po location you gsto k sana ipaadjust ung scooter k
Nakailang try ako pagsabayin ung dalawang button kaadik pero wala lumalabas..e10 pro max sya..njax-t dn ung controller
Goodday kaadik!
Nakabili k n pla ng scooter mo.
Congrats!🤟
May mga ganyan na nangyayare eh. Di ma-access un P-Settings.
Nai patingin mo n ba yan sa pinagbilihan mo?
@@jaysonulanday kakabili ko lng kahapon kaadik kasi nagandahan ako kay unggoy gusto ko din gayahin mga upgradesn mo
@@jaysonulanday hindi pa kaadik dun ko binili sa shen shen kaadik sa pinagbilhan mo ng battery sabi ko nakita q kasi shop nila dahil sau..
Sir. Recommend naman kung saan mo nabili ang Scooter. Planning to buy din po ako for daily trasport use po. - Abu Dhabi
Goodday kaadik!
Behind Madinat Zayed.
Proffesional Bicycle shop.
Maraming salamat sa panonood😃
X thunder gamit ko po gear 3 n sya pero max takbo nya 50 lng bakit ganun?
Goodday kaadik!
Nagalaw mo n b un p-settings mo?
@@jaysonulanday opo
@@jaysonulanday pano kya pwede gawin dun paps?
@@lucasgabrielhernandez6095 pm mo ko sa fb ko.. may ise send ako sayo na guide. Photo kase un.. para mai send ko sayo kaadik!
@@jaysonulanday same name po boss pm send po thanks
Good day sir pasagot naman po ako baka may idea kau.. bumili ako ng e10 kagabi pero iba ung throttle nya hindi kagaya nito.. tapos wala pang manual sa box.. baka pwd pasuyo sir ito ung available na P settings nya.
P - 3
P - 6
P - 7
P - 9
P - 15
P - 16
P - 99
tapos bro napansin ko kahit full charged maman ung battery pag pinipiga ko ung throttle minsan may lumalabas na warning sign triangle na red tapos nawawala rin kaagad.
Goodday kaadik!
PM mo ko sa fb, send ko sayo un copya ko niyan.. mahaba eh.
Salamat sa panonood!
Drive safe!
same issue ako neto sir,pano ba dapat gawin para maiset ung sa voltage,ganito din po settings ko,salamat po
Hi Jason, I hope your ok. Can you help me with something please? When I go into the P settings on my scooter, which is a 48V , scooter 600W on P setting 1 which is the battery voltage I am unable to bring the number up to 48, the highest number I can get to is 28.4, If I continue to try and up the voltage I get the empty flashing battery like what you got on your video. Can you tell me why you think is happening?
Sir.. may tanong lang ako kasi bumili ako ng E10 scooter nung friday unang gamit napansin ko sa kalagitnaan ng takbo humhinto na sya di na gumagana accelerator nya at ayaw ng tumakbo.. pinapalitan ko kahapon ginamit ko yung bagong palit na unit tpos same parin naging prob biglang huminto.. factory defect b sya? Same problem lng din.. sana matulungan mo ako sa prob ng scooter ko gusto kong papalitan ngayin ng ibang model nlng
Goodday kaadik! Un isang bilihan ng scoot dito sa abu dhabi sinasabi nga na nagkkaproblema un mga bagong unit ng E10. Kung maibabalik mo p yan gamit un warranty, mas maige n magpalit k n lng ng unit.
Di na kase maganda un mga bagong E10 ngayon.
@@jaysonulanday ah kaya pla.. binalik ko na sir ung unit sabi bigyan nlng nila ako ng ibng model wag lng e10.. ano b mas maganda sir?
@@boyjackpottv9585 mag X Thunder k n , may kamahalan pero naka porma na agad.
Buti madali kausap un pinag bilihan mo.
@@jaysonulanday cge seach ko yunh x thunder sir
Thank you sir
salamat Lods 🙏
Goodday kaadik!
Maraming salamat din po🤟😀
Ka scoot good day sinet ko ng 43 ang P1 settings ko, pero bakit po kaya hindi nacut or nashutdown ang power voltage ko 40 na lang sya pero natakbo pa din although sobrang bagal po sya, chinarge ko na din for assurance hehe.
Goodday kaadik!
i-monitor mo na lng.
Pag nasa 43V na lang saka mo i charge.
Nice!
Yung sakin ayaw mag appear ang settings. Speed lang pwede kong baguhin
Pare ilang speed ng e10 mo
Goodday kaadik!
Dati nasa 38kph lng(gps speedometer)
Ang bigat n kse ni unggoy dahil sa mga accessories lalo n un acrylic board at battery.
After ko palitan un controller nasa 41kph na
Check mo un "Drive Test" na latest upload ko pre.
Have a nice day pre🤟.
Hello bro hope you doing well
I have e5 same setting can I set my voltage to 70 from 43
And Also my tyre diameter was 6or 7 I think I changed to 10 is that ok?
The tyre on scooter is 10inch
Yes or no bro
goodday bro!
Sorry for the late reply.
If ur scooter voltage is 48, set ur cutoff(low voltage protection) at 43v.
The tyre size will affect the speedometer calcultation. It has nothing to do with the speed.
To get accurate speed calculation, use GPS Speedometer. Then match ur throttle controller speedometer by adjusting the tyre size until you get the right value that matches sa GPS Speedometer.
You can download from your android fone. SPEEDOMETER app.
Thank you for watching!
Drive safe!
@@jaysonulanday thanks bro stay bless can you make a video on that please
Boss parehas lng ba settings niyan sa e10-t13 2021
Goodday kaadik!
Kung same lng po tyo ng throttle..possible po na pareho lang.
Generic kase ang E10, magkakaiba un throttle.
Ride safe!araming salamat po
I changed my P0 settings by mistake and still give me wrong speed reading even I put my tire size 10 inch... any help?
Goodday!
Bro just put 5inch
(rim size in diameter)
Have a nice day🤟
Paps pa help nmn bkit ung p settings ko p0-p6? May idea ka dn ba panu ireset ang e10?
Goodday kaadik!
Anong throttle gamit mo?
Pacnxa na po, late reply..
Njax t din kaadik
Pa shout out dn pla sa next video kaadik
@@donvalladolid4996 parang may dati ng nagtanong sakin niyan "p0-06" din.
As long as ok nmn un performance ng scoot mo. Ok lng yan.
Ok po, shout out po kita.
Maraming salamat po sa support kaadik!😀🤟
Salamat kaadik minsan sama ako sa ride mu basta friday hehehe godbless more power kaadik