How To Clean Your Janome Sewing Machine (Mechanical Straight Stitch Machine HD9/1600P)

แชร์
ฝัง
  • เผยแพร่เมื่อ 6 ก.ย. 2024

ความคิดเห็น • 45

  • @raggedyanna6-Missy
    @raggedyanna6-Missy 2 ปีที่แล้ว +5

    Finally I see where to oil!!

  • @iamjustonemom1950
    @iamjustonemom1950 ปีที่แล้ว +1

    For Janomes that do not have oil holes on the top, they need to unscrew the two screws on top and lift the lid off. If you are fortunate to have a good service tech near by, take it in. I like to be able to do general maintenance myself because I use my machines everyday for hours. So in addition to the wick under the bobbin, there are 2 other wicks in the top of your machine. Unscrew and search until you find both, one to the right of center near the main shaft and one tucked up in a gear area to the left of center. If it is white, yellow, and dry put at least 4 drops over the course of 5 minutes. Many machines are sold with dry upper wicks. We all know about the wick under the bobbin but I only found out about the upper wicks from a serviceman that came to do all my machines.
    Reply

  • @sandracoupje
    @sandracoupje ปีที่แล้ว +1

    I was especially looking for how to open it to clean the dust at the bottom of the bin. Inside the machine. The part you can't just handle.

  • @peggyross3873
    @peggyross3873 8 หลายเดือนก่อน +1

    Thank you! I love the video and will use the tips for my Janome HD9BE. One question- where do folks find a micro vacuum tip (something to work on a Dyson hand held would be ideal)?

  • @raggedyanna6-Missy
    @raggedyanna6-Missy 2 ปีที่แล้ว +2

    Thank you I can finally see where to oil the bobbin area!

  • @betsymegna6263
    @betsymegna6263 ปีที่แล้ว +2

    Do you need to also put oil on the wick in the bobbin area? I though you did need to do that.

    • @dmarie1157
      @dmarie1157 ปีที่แล้ว +1

      They did not mention that but the manual does specify to oil the wick in the bobbin area.

  • @GeraldineMPenny
    @GeraldineMPenny 7 หลายเดือนก่อน

    Fantastic instructional video. I wonder about the little sponge area just before you get to the bobbin itself? I had to bring my machine in for servicing and was heavily scolded for over oiling my machine! Thanks for this instruction.

  • @palmasmyth6605
    @palmasmyth6605 2 หลายเดือนก่อน

    Thank you for your valuable information.

  • @angelamcgovern1525
    @angelamcgovern1525 2 ปีที่แล้ว +2

    In the book is say to put oil on the sponges wick thing that is opposite the bobbin case

    • @myrnapetit6012
      @myrnapetit6012 2 ปีที่แล้ว +1

      I was just going to ask this question? Does this sponge pad need oiling?

    • @lamarlatrell5045
      @lamarlatrell5045 2 ปีที่แล้ว

      @@myrnapetit6012 I oil mine

    • @dmarie1157
      @dmarie1157 ปีที่แล้ว +1

      yes

  • @buickjim
    @buickjim ปีที่แล้ว

    What I would like to see is a quick video on the effects of the Pretensioner. I use thin thread for piecing (Aurifil or YLI Soft Touch (60/2)). I find that just going through the closest hole in the arm to the upper right of the pretensioner and into the pretensioner works well well with thin threads. I don't go through the two "outer" holes to create additional tension.

  • @celestebrown1915
    @celestebrown1915 ปีที่แล้ว +1

    I love the chair. How can I get hold of it?

  • @patricialara2539
    @patricialara2539 ปีที่แล้ว +1

    Do you have a video that talks about the pressure of the foot?

  • @buickjim
    @buickjim ปีที่แล้ว

    Have you used the 1/4" flange foot for the HD machine? It creates a perfect 1/4" seam allowance. Unfortunately that is too large and doesn't take into account the fold and stitching. I was taught to do a seam allowance test by taking four 1-1/2" wide strips of fabric and sewing them edge to edge. The resulting unit should be 4-1/2" wide and the two interior strips should be exactly 1" wide when measured.
    When I used the 1/4" foot (similar to the "O" foot) the unit was 1/4" too narrow and the interior strips were only 7/8" wide. I switched back to the T-shaped seam guide (anchored by a screw) and after a couple of attempts, got the seam allowance to a perfect quarter inch such that the test unit measured exactly 4-1/2" wide and the interior strips were exactly 1" wide.
    Are there any adjustments that can be made to the foot so that you can get the seam allowance to come out exact?

  • @welshwitch2126
    @welshwitch2126 ปีที่แล้ว +1

    My bobbin has NEVER clicked like that. Everybody talks about theirs clicking and mine never has. I have a V1.

  • @MamaChristine
    @MamaChristine ปีที่แล้ว

    Would like to see an unboxing video of HD9 and the boxes of feet available. Website Janome has is not easy to navigate.

  • @valerierosel2399
    @valerierosel2399 6 หลายเดือนก่อน

    Where can one find that tiny vacuum cleaner?

  • @craftingstar777
    @craftingstar777 2 ปีที่แล้ว +1

    Can you highlight the different kits for this machine or some of the special accessories available! hehe

  • @annieconstant
    @annieconstant 2 ปีที่แล้ว +1

    Thank you this is so informative! Love love love!

  • @vickiclose2259
    @vickiclose2259 2 ปีที่แล้ว +1

    If you hear a metallic “ping” (that sounds like it is coming from the tension disk) is that an oil issue or a spring or is that normal for this machine? Thank you

    • @janomejunkies2044
      @janomejunkies2044  2 ปีที่แล้ว +1

      Well considering you don't oil that area I would assume its a spring issue... When is the last time you've oiled the whole machine though?

  • @raggedyanna6-Missy
    @raggedyanna6-Missy 2 ปีที่แล้ว +1

    Thank you so much for this video!!

  • @lovnbnhome
    @lovnbnhome ปีที่แล้ว

    My hd5000 booklet says no oil, is that true? Thx!

  • @majdoulokman294
    @majdoulokman294 2 ปีที่แล้ว +1

    I liked the sewing machine and I want to buy how can I do that I am from the country

    • @janomejunkies2044
      @janomejunkies2044  2 ปีที่แล้ว

      Give us a call 813-661-9000 M-F 10AM-4PM EST we will make sure to take care of you before and after your purchase :)

  • @karynyoung1464
    @karynyoung1464 ปีที่แล้ว

    My stitch plate is on so tight I can not loosen the screws - any suggestions?

  • @CrystalKay356
    @CrystalKay356 2 ปีที่แล้ว +1

    Good video! I have the HD9 but have a hard time with tension, little info...I do bag making and like to use waterproof canvas for many of the linings but it has a hard time with a nice looking bobbin stitch (ie pulling it up) I have the top tension almost as tight as I can tighten it, I normally use a 16 or 18 size needle & T70 thread, any advice? Thanks for the videos!

    • @janomejunkies2044
      @janomejunkies2044  2 ปีที่แล้ว +1

      th-cam.com/video/zxp4-VWB24A/w-d-xo.html Check out this link for a video on tension :)

    • @michaeltexeira6185
      @michaeltexeira6185 ปีที่แล้ว +1

      Use the nylon thread on the small cones.

    • @CrystalKay356
      @CrystalKay356 ปีที่แล้ว

      @@michaeltexeira6185 thanks for your reply, what thread are you referring to? I use bonded poly on the cones, would that be close to what your referring too, if not could you refer me to what you are suggesting, what text and where you purchase? thanks

  • @Angeline_Chnt
    @Angeline_Chnt ปีที่แล้ว

    hello, a highly recognized technician in France says that this machine does not need oil and that for normal use it must be oiled every 2 years, for so-called professional use it fades it every year at the same time as the revision. He laughs and says they are a barracks frit differently. Frankly, it’s a real red flag 🚩 😮 1:11

  • @karynyoung1464
    @karynyoung1464 ปีที่แล้ว

    Do you sell the t screw driver? What kind of machine oil do you sell?

    • @janomejunkies2044
      @janomejunkies2044  ปีที่แล้ว

      yes we do :) And triflow is what we sell janomejunkies.com/product-category/machine-care/
      Here is a link. We sell tri-flow and the T screw will be on that website too.

  • @raggedyanna6-Missy
    @raggedyanna6-Missy 2 ปีที่แล้ว

    Where do I find the mini vacuum please?

    • @janomejunkies2044
      @janomejunkies2044  2 ปีที่แล้ว

      This one was from Home Depot. The nozzle I'm not sure where we got that.

  • @koalabathnbody4748
    @koalabathnbody4748 7 หลายเดือนก่อน +2

    Hi, Great video but could you not talk so fast it makes it hard to hear what you have to say. Thank you.

  • @michaeltexeira6185
    @michaeltexeira6185 ปีที่แล้ว

    Nice store. Next time do a. Removal of Top cover. Plate Etc. Bottom cover. Face plate cover. Cleaning by air compressor. Blowing all dust out. oiling All felts. Hook body. Needle bar mechanism Etc. That ring on your pointy finger is too tight,,,or send ticket airplane and I will help you. Haaa