Put Glue Into Sawdust and You Will Be Amazed With Result!
ฝัง
- เผยแพร่เมื่อ 23 ส.ค. 2024
- A lot of wood chips and sawdust are formed in the workshop of woodworkers and carpenters. These wood dusts are usually swept up and thrown away. However, it is possible to use wood powders in a very useful way. You can combine wood shavings and dust with glue to obtain wood filler. You can use this paste you have obtained to fill the gaps in the wooden parts. If you are wondering how to evaluate your wood dust and sawdust and how to make homemade wood filler, you should definitely watch this video.
Have done this for decades.
It's important to use the dust from the same species of wood to fill the hole. Also, using an electric sander will tend to heat up the glue making the fill darker and gum up the paper. Use the glue-dust fill sparingly and hand sand.
"Have done this for decades." Me too, nothing new under the sky... Try with superglue (cyanoacrylate) do not mix it, poor the glue on the saw dust in place... in case of a bad joinery, use two components glue instead...
@@garoudahanouman7734 yea agree
Agree
@@garoudahanouman7734 so have I, variously using cyanoacrylate (superglue) for a quick job, or epoxy resin where time is needed for accurate assembly.
Only yesterday, I used rapid epoxy with paper kitchen towel, to fill an enlarged screw hole in veneered chipboard, which was to take a cup hook. Within minutes the hook was weight bearing.
Agree.. Tried & tested method, plus near enough to free for small jobs. Can’t go wrong.
Been doing this for years. My favorite trick is to use particle board for work bench table top. It is cheap and very smooth and flat. Good for project surface to work on. I drill parts right into the table. After a while, just mix up sawdust and glue and fill drill holes in my work surface and sand them smooth. Good as new since particle board actually is just sawdust glued together.
l
sawdust once sifted leaves a finer powder more manageable and much less coarse finish Start with unsifted and finish with sifted
Cléopâtre glue also holds pores and varnish outdoors
La sciure de coupe une fois tamisé laisse une poudre plus fine plus encore maniable et finition beaucoup moins grossières Commencer avec non tamisé et finir avec celle tamisée
Colle Cléopâtre tien même en extérieure elle aussi de bouche pores et de vernis
This works well for painted projects, but it's not recommended for stained projects. The wood glue / sawdust mixture will not stain well at all.
An option to use when staining a project. Use the same stain you're going to use with your project and mix it with the sawdust. Then, mix clear
Like this!
Why
I've used saw dust and wood glue mixture as a filler.Mixing the stain that you're using into wood glue and saw dust mixture does work well to get the color you need.
I've got jars with different colors of sawdust I've saved from sanding for this reason. Works way better than the store bought stuff. A+ tip right here.
Apparently this guy thinks this is a NEW idea...Been doing it Myself since the 1950's. An OLDER thing.
@johnsmythe6134 I'm sure he never said he came up with it. He simply said A+ tip.
If you sand wooden floorboards and decide to fill the expansion gaps with wood filler save money by mixing latex base adhesive with the sawdust from sanding the boards and use the "filler" leave a slight dip in filler to allow for expansion, I did a 20*12 foot Victorian dining room floor for a friend like that and it's still good 10 years later
😊😊
Great idea!
This would work a lot better if the sawdust was from the wood you were working on
Not much. Any sawdust darkens in a mixture with glue.
Maybe that's where the downvotes are coming from!
@@Walker7745 that's why you use clear epoxy instead...
the man doesn't fill 8 minutes of crap to monetize the video, just went to point, nice and clean, Man
Diese Tricks zeigte mir damals schon mein Berufschul Lehrer in unserer Tischlerei ! Guter Tip 👌👌👌
Да да, этот способ я применял ещё в прошлом тысячелетии.
Это было оооо очень давно!
Только не опилки, а пыль от шлифовки.
Аналогично! Даже по времени! Как только я увлёкся изготовлением изделий из дерева!
но буквально вчера ученые изобрели шпатлевку. нужно сказать автору про нано технологию будущего. А шип-паз надо за ранее замерять и делать впритирку.
This method is as old as the hills my Dad thought me that when I was a little boy of 10 when I made some bad school woodworking projects to hide after my inaccurate joints and cutting but thanks for bringing back a 55 year old memory. 👍
Same here.
I had this idea while watching a show with my son, looked on TH-cam and watched this video. Just tried it on a bowl I have been working on that has minor cracks. Worked perfect!! Plus it dries super fast for inpatient guys like me.
It's a very good idea, I use it a few time ago and find work even better with wood sealer, TKS for the video
Saya sudah lama pakai tehnik ini,,
Terimakasih sudah berbagi untuk yang belum tahu tehnik ini. 👍👍
Always nice when people rediscover what generations before have been doing for 200 years/ possibly more. We have to pass information on to to the younger genertions. Paricularly these days where so many people can't do anything they haven't seen on the internet.
Sadly, you're right. With fractured families, mentorship that doesn't seem to exist anymore, and people living their lives on social media, if you don't see it somewhere on line, it doesn't seem to exist anymore. Mine is an overstatement, perhaps, but more and more, it's true.
@@johnsposato5632 .. Overstatement? Not at all. Only the internet also leads people to think they know a lot because they can get info at the tip of a button. The problem is that they are often then partially informiert and believe they know so much. The knowledge that is accumulated through doing the actual work can't be lerned online ...That takes years of experience.
@@robertthomas6127 Yep.
@@robertthomas6127 I get that in my job , I’m a bricklayer and have been for nearly 40 years. The amount of people iv done work for that have seen a load of old crap on the net , then try and tell me how to do my Trade is unreal.
@@richardadams6821 .. I can believe that. What I love the most is when those kind of people conviently find a reason to disappear from the job site when a problem turns up and return when it is solved. Afterwards they then explain the situation to others as if they knew all along what had to be done.
Паркет ещё в 18 веке так правили... неужели есть мужики, которые эти способы не знают...
Есть просмотры значит есть и мужики))
Старо как мир.Но молодым пригодится.
If surface finish is hidden, it may help to use this type of process. For a stained finish it will pay dividends to use your tools and work processes more accurately. e.g. The half-housing joint was out of true and measurement by a country mile. The final appearance would not pass a customer's inspection. The knot was filled and sanded and was still left looking rough. The drilling of the the square length of wood showed that you drill bit was not square in the chuck (or the drill bit was bent). The technique for hidden screw holes is to use a chisel to raise a plug of wood which is larger than the hole. Drill the hole and place the screw then glue and clamp the plug of wood. Sanding the result will yield an invisible screw hole. You will drill much better holes if you use drill bits designed for wood rather than metal. These are known as Brad Point drill bits and can be used for soft and hardwoods.
Pokud je člověk mladý a nehraje si třeba s modely ... může to být pro něho novinka. Je mi šedesátpět a tohle jsem používal když jsem stavěl modely jako dítě. Je to fajn umět si poradit.
Sometimes old stuff is new my father did this probably 50 years ago and taught me how to do it at least 40 years ago. Works quite well
Yup.... my grandfather did this in his cabinet making over 50 years ago.
Так учил меня ещё мой дедушка.
Muito bom tacada de mestre continui demostrando truques de mestre continui demostrando ajuda muito obrigado alegra o coração fica com Deus DEUS abençoe vocês paz profunda SOMOS vencedores Deus os abençoe vocês....São Paulo Brasil s c s SP .....
thank you for the good idea, I also use metal grinder dust I collected for cement mixture.
What for? Do you dream of making a whole sheet?
Красить начнёшь,все вылезет...пятнами)))
A very creative idea. 💛
I look forward to seeing your designs. Congratulations on your journey forward 💪🤝
ich benutze schon lange dieses Systhem wenn man es richtig anwendet eine gute Qualiät Holzleim benutzt und feines Sägemehl gut vermischt ist es trotz Unkenrufen aus bestimnten Ecken ok
I LEARNED THIS IN WOOD SHOP 78 YEARS AGO. I ALWAYS KEEP DIFFERENT GRADES OF SAW DUST I SAVED FROM DIFFERENT PROJECTS.
Только что был вынужден применить подобную шпаклевку. Только не с ПВА, а с эпоксидкой. Делал каретку для циркулярки и когда свинчивал половинки, одну доску увело аж на три миллиметра (как? из-под струбцины?), край каретки стал с изломом, не прямой. А сажал все на клей. Увидел, когда уже все высохло. Переделывать... ну, нафиг. Наклеил на стол скотч (чтобы доска к столу не приклеилось), на ребро доски налепил смеси опилок с эпоксидкой и положил доску на скотч. Стол дал базовую плоскость. Лишнюю шпаклевку снял. Завтра высохнет, края обработаю от облоя и буду иметь прямой край каретки.
Почему эпоксидка, а не клей? Сохнет быстрее. Клей в толще остается мягким несколько суток.
И эпоксидка лучше шлифуется, в отличие от ПВА.
А ещё, если в эпоксидку вместо опилок замесить аэросил, будет прочно и шлифуется легко.
Цемент+эпоксидка
It’s why I save sawdust! Amazing filling material!
back in the 1950s we used flour as a glue with saw dust.it would dry hard and a nice light colour. try it. UK.
I use it from 1993 , when I started wood working!!
Tengo 50 años y desde niño mi padre lo usaba de esa manera en los trabajos de carpintería, sin duda es bueno.
да это просто кладезь) как ты смог до это додуматься, это же феноменально
¡Por fin alguien q muestra "mi" técnica para restaurar maderas! Yo soy un absoluto fan de esta técnica q permite reparar todas nuestras imperfecciones. Tengo frascos con serrín de diferentes tipo de maderas y con un colador o tamiz de cocina me hago serrín de granulometrías diferentes. Incluso guardo el polvillo q resulta después de lijar, lo q me permite la "terminación" de la reparación. Nunca è usado ni usaré mezclas epoxidas para reparar maderas: Las maderas se reparan con maderas, es mi eslógan. Incluso he reconstruido trozos de centímetros, con la técnica de la paciencia. Una capa, espero q seque bien y agrego otra capa, hasta llegar al lijado y disfrutar de lo realizado. Aunque sea difícil de creer esta técnica, al menos a mi, me ha permitido pasar estos dos últinos años, con todas sus medidas liberticidas, en un estado de casi plenitud; ¡de verdad! Saludos y felicitaciones al autor del video.
Não deve ser usada espátula de metal, mas de silicone ou de madeira para não escurecer a cola
The specialist who loves quality.
Why is the dust grey? Shouldn't you use the sawdust from the same wood?
Нашёл чем удивить,...
Para o reparo não ficar escuro,acrescente gotas de limão à cola e serragem
Oh mi 0
Я добавляю лимонный спирт
Isso mesmo amigo, pois não escurece com limão, fica perfeito.
I've always called this "Wood Filler" Very common practice for older wood workers like myself before the advent of all the fancy stuff you can buy at the store. lol. Waste not, Want not.
A friend of mine alway told me that you can tell a good Woodworker, by his ability to correct and hide his mistakes. Your video illustrates a good technique, I'll use.
Охренеть , вот это да !!! Как такое только людям в голову приходит - смешивать опилки с клеем ? Шестьдесят лет живу и впервые вижу !!!
А мебель из дсп тоже первый раз это старо и было задолго до того как моявилось ДСП 🤔⚠️
@@user-ho2ov8co5x , спасибо , уважаемый , вы мне тёмному прям глаза открыли !!!
@@Имярек-1 сказал как есть без обид!
@@user-ho2ov8co5x , какие обиды , дружище , это изначально была ирония ....
Mixing sawdust w/ clear epoxy can match better w/ the same kind of wood (used in the sawdust) than a white glue. & much stronger...
Mix sawdust in with latex paint, when it dries it's as hard as a rock, but can be worked just like wood.
Takes a while to dry though!
GREAT idea with some color in a knot it could end up looking like epoxy! !! !!!
Para el tipo de pegamento ilustrado, es mejor no usar herramienta de hierro/acero porque oscurece la masilla, cambiando el color madera.
Mixing the saw dust and glue with the same color stain you're using works great.
No hay mejor resanado en el mundo , los resanes comerciales se resquebrajan , con el tiempo, en cambio esto por ser más orgánico , no tiene sustituto ! Es muy buena orientación , para toda persona, que por sus múltiples ocupaciones , no tiene tiempo de reflexionar , y esta solución es mágica siempre! Saludos 🖖😃🇲🇽
Bravo 👍
I was taught about something similar maybe 50 years ago. When site built cabinets were built, finish nails were counter sunk or "set" and glue was put in the tiny depression. After it had begun to harden sanding briskly would make that place almost invisible.
Keen to try this method, learnt something 👍🏻
@@marcosavio1020 I am not positive but I think there is not a day goes by that I do not learn something new, especially now that I watch TH-cam Somewhere over 60 years of woodworking and I still love making saw dust and learning from others. True woodworking not by a CNC or carve master but honestly hand made is unbeatable.
Home made wood putty!
This just in, man discovers...
*FIBREBOARD*
Fantastic tip.Thank youuu!
As long as you can make it on the spot, epoxy or CA glue works better bc it wont blacken like regular paste glue and will match the piece better
This has been a method used for decades, what is not shown here is by using the sawdust from the same wood type or piece you need to fill you avoid seeing a substantial colour difference between the work piece and the filler.
In glue & dust I place my trust,,, if all else fails use 6 inch nails...
Really handy tip if normal wood filler is not available, providing you can buy wood glue. 👍
Been doing this for years this trick has saved me a lot of grief. But make sure to use sawdust from the same color wood I save all my sawdust have different colors
Спасибо что выкладываете такие вещи,кому то это поможет.
Эти вещи мне трудовик в школе показывал
Works great on filling nicks, cracks and scratches on gun stocks too.
Таку шпаклівку я використовую з 90-х,дуже міцна і надійна.
После высыхания эта смесь дает большую усадку. Нужно повторять.
Homemade wood filler. The best ideas are always the simple ones.
Aadding sawdust to glue can also help with color matching when staining. The sawdust absorbs the color, the glue does not.
Show me something my dad didn't teach me when I was 8. I'm 60 so I've known this for 52 years.
Stupid question…. But how long do you typically have to wait until you can sand this homemade wood filler?
Adicione algumas gotas de limão 🍋🍋🍋na mistura, e não ficará escuro!!!
Aee parceiro ...eu ia dar a dica mas vi.seu comentário, essa e das antigas em kkk pouca gente sabe
100 лет в обед
Good joiner...solid as rock
شكراً جزيلاً
A slight twist on this is using fine grained swarf to fill cracks on commercial aircraft ...... but mixed with a very advanced resin adhesive. The idea is the same.
I use wood glue and saw dust for a long time now and it makes everything rock solid.
Thanks,I need to use this for a project.
Muy bueno el truco.gracias por compartirlo y animo con el canal👋👋👋Saludos
Сто лет назад так делал. Засыхает намертво. Лайк.
My Dad taught me this trick 50 years ago.
Я 14 лет назад делал такое. Опилка от шлифовки очень хорошо прилагаются
I usually use 2p10 thick and the dust from my sander bag that matches the wood I am using for larger holes/cracks or for small ones like in the knot I just use 2p10 thin and sand over it. It creates a closer match and not so much of a grey look.
Better than welding, plus a lot nicer & easier material to work with.
Buen día una pregunta, para aberturas, puertas agrietadas por estar al exterior, es una solución? O el agua, el sol le perjudica gracias por subir videos, saludos de Puerto Iguazú argentina
Auf diese Idee bin ich schon vor Jahrzehnten gekommen nur mit Knochenleim ,
We did this same thing when I was in grammer school. We would make all kinds is animals and cups abd plates birds... .it was so much fun.
In glue and dust we place our trust😁👍
how strong is the filler? e.g. will a screw in tapped filler hold the same or more as wood, including if pulled directly out?
Bonjour c très connu mon père l avais appris quand il étais apprenti menuisier en 1953 !! Qui me l appris en 1977 !! Qui moi même l ai appris à mes enfants. C deja loin et la retraite dans quelques mois bonne continuation. Yann
Ist ein uralter Tischler Trick, kenn ich von meinem Opa schon und ich bin heute auch bald ein solcher ;-) Bei ihm hieß das "Pfusch- oder Russen Fuge"... Wirklich!!!
Senas bajeris.
Bet geras 👍. Senai naudoju
Этому результату 1000 лет
Which bond is good to use.
I tried with title bond III. But it blacks / darks too much in my red oak project
I used Durham's water putty... Woks well.
para evitar que la pasta se engresca se recomienda usar herramientas que no sean de metal mejor plásticas o papel, ademas se añade unas gotitas de limón a la mezcla esta mantendrá su color original. un saludo desde la bella Guatemala.
In Thailand , we do this long time ago . It works
Does the glue oxidize the wood? It would explain why the resulting filler is always darker color than its constituent parts.
Oh! Hai inventato lo...stucco per legno! Geniale! 😱 😏
пипец мы поражены...а еще вместо опилок можно туалетную бумагу крахмал цемент гипс и... да блин все что всасывает пва....
A chippy showed me this method about thirty years ago and have used it ever since :)
I was doing that 50 years ago building model airplanes, old trick.
Kitt und Leim macht alles fein.... ;-)
Wow, he invented wood dough.
All I need in life is sawdust and glue.
О, чудо из чудес 😸🙀!
..a nebylo by účinnější tu nepovedeně vyfrézovanou drážku slepit rovnou tou pastou?
Я лет 35 этим пользуюсь.
O resultado é bom, mais há dificuldade em lixar já que a cola branca fica emborachada, como eu uso muito esse sistema tenho melhor resultado com araudite ou resina epóxi.
He should’ve use the wood glue combination for everything.
Not really surprised. It makes wood putty . this is also how particleboard is made, just uses a combination of sawdust and wood pieces.