Thank you for the well illustrated advice. For a normal electric drill, you have to use a spanner to immobilize the threaded shaft that holds the chuck before striking the L key.
I took my electric Makita outside with the hex key in place, held it to the ground and put it in reverse. It did unscrew the chuck when the hex hit the ground, when hammering didn't work.
I was listening with headphones and that knocking at the very beginning (in only one earpiece) had me jumping in my seat like "how the hell is someone knocking at my WINDOW? On the first floor???" Don't do that!
tried all you recommended but to no avail ,I had to cut off most of the old chuck with a hacksaw and then heat up the remains with a blowlamp (gas torch? USA ) only then did it come off . I must say I was very near throwing the thing in the trash (rubbish ) UK . took 2 hours.. and broke 3 impact driver bits trying to remove that centre screw .. even when I drilled out the screw the chuck would not give up and move.. thank goodness for heat .. I felt like had won the lottery when the chuck finally came off.. Conan, UK
I would love to see how someone would remove a stripped chuck on this 20v Porter cable drill I have the internal gears are stripped so it just slips even with air gun on it and yes the screw has been removed
@@elmerovero7528 Start with the heres how to drill through your hand bit work next on the hitting with the side part of a dead blow hammer end with the if only i had some vise grips part is that enough or do you need more ?
I’ve removed the retaining screw, but can’t get the Allen key to undo the Chuck, it’s just turning the motor of the drill. Drill clamped to bench, low gear, drilling mode, 10mm Allen key and hitting anti clockwise. Any ideas?
i have a Makita XPH07 and i got the screw out, but the chuck does not want to screw off. I;ve got it in the drill setting on no.1 as another video suggested. It is turning, but not coming off.
I have an old Ryobi D45C which uses a two part chuck with a thin nut at the bottom of the chuck. No retaining screw. The jaws are seized. How does one remove an old chuck like this?
Squirt a bit of WD-40 or any other kind of lubricant on the chuck and let is set for a minute. You can put some vise grips on the chuck and try to bust it loose with a hammer.
Im trying to upgrade the chuck on a brand new drill and the retaining screw itself is not the problem. The chuck is screwed on so tight, I assume there is loctite involved. I could not get it to move no matter how hard I hit the allen key and I even damaged the chuck in the process. Can I take apart the gearbox from the inside to get the shaft out?
Excellent video. My keyless chuck had jammed - shut of course - so I had to grind it off, but the video showed just where to grind, and the bit about the wrong-handed screw was essential, as was the advice on cooling and heating. Both were needed, so maybe you did it right. Tip: if your drill is a DeWalt, it has a Torx 20 screw. If you try to undo it fresh out of the freezer, the Torx bit shatters...
How come when i whack the allen key the drill wants to spin and wont get the chuck loose ? Am I missing something here. The drill is on low speed (1) and when i turn the allen key by hand first it stays really tight until i whack it with the hammer and the drill slowly spins. Is this just a really stubborn chuck or any other suggestions ? It is a newer Makita brushless hammer drill.
@@RiffRaffMama. Sure, will be my pleasure, where do you live, if you are far to from me, I have a solution for, you can take your drill, go to neighbor ask for share his drill for 2 minutes and do the job in his home, then give back it and say thanks. I am sure nobody will reject to share for a few minutes.
@@RiffRaffMama. By this reason I have two drills, one cordless for easy and fast jobs, and other corded to do rough tasks (stone, concrete). You should to consider to buy another drill too.
My driver drill's chuck has misaligned jaw (2 stucked at lower part, 1 at middle part). This method still unable to fix my drill issue. Do i need to replace the entire chuck?
Putting this here just in case it helps someone. I was watching this because I thought my chuck was damage, motor was spinning but chuck did not move. Turns out my drill was somehow stuck between 1 and 2 speed, making sure it was fully switch to one of the speeds fixed it. Good thing too because I couldn't for the life of me get the chuck to come off with the hammer and alan key!
My harbor freight battery drill jammed. I saw the little screw and couldn't undo it so I did as suggested - tapped it with a long nail. The screw vanished and the chuck started working again.
hello the problem is my device has 2 chuck its black & decker cordless 14.4v driver/drill i have screwed out the screw so easily but the problem with the 2 collars after turn one it goes to point that stop and start turning the one behind it so i tried to use 2 wrench one fix one and another wrench to loose the another collar but here is the big problem it doesnt loose whatever i push it so how to replace this doomed chuck i am stuck now with broken jaw teeth??!!
My makita teeth wont close, they are locked all the way open so bits just wobble inside. the chuck it'self wont turn much, just barely moves one way or the other and makes a snaping/locking in place sound when I turn it clockwise. sound like it should make that sound. luck the chuck is slotting into something. sorry i'm not a tool buff not sure how to explain it better. Do I still need to bust it open like this?
There seems to be a million videos on removing a chuck, or fixing a chuck with a bit stuck in it. But I have twice accidentally opened a double-sleeve keyless chuck too far and it won't close again. Are there any videos on how to fix THAT?
I have a drill chuck with the reverse threaded screw removed. The CHUCK seems to be stuck and I cannot use a normal method to remove it. I think some one may have locktited the chuck but as it was newly purchased it may simply be caused by a seized thread. How can I remove the chuck? Good Video but doesnt apply to my problem.
Hi. Thank you. My 3/8 Stanley cordless drill chuck got stuck with a 6 mm bit in it. I didn't grip it too much, just normally, but it won't undo. It's stuck. Please share some ideas to free it up. Thank you!
Does any one perhaps know why a chuck starts to rattle and slip when i try to loosen it. It sounds like grinded teeth. It still drills and drives. Yet manually loosening the chuck sometimes makes this rattling sound
Time for the hammer, LOL! When this happens I've had good luck using a hammer and a punch. Clamp the stuck bit in a vise with the bottom of the drill chuck facing up. Place the punch on the chuck's body next to the jaws. Strike the punch with the hammer until the chuck's jaws slide off of the bit. This method will usually work. In the rare case that it doesn't, I will resort to cutting the chuck off of the drill with a grinder and cutoff wheel. -Mark
Hi, My problem is with a Porter Cable cordless PCC600 with a broken Chuck stock about 5/16" open, but will not close or open running the motor back and forth, it's broken gears and Im unable to remove the inside T20 screw any ideas how to replace this broken chuck?, Cause the motor runs fine, it's a great drill and I will really like to keep it. Please let me know. Thank you! we
Hello , I have a Makita LXPH03 cordless drill , the problem I have is that the chuck pulls out of the gearbox with shaft intact..Is there any way to fix it?? Thanks
Unfortunately the shaft is part of the 126448-9 Gear Assembly. Makita does not provide any parts for the Gear Assembly. You would have to replace the complete gear assembly.
My countersunk is stuck in the chuck, and the chuck is stuck, impossible to undo & release my countersunk, so I am unable to even get to the stage of checking the chuck screw inside....
no, I couldn't do it, but then my hands are a bit older & weaker nowadays... I took it to my local hardware shop, and the very helpful guy did it with one strong twist. It had got a bit clogged with some plastic from me drilling holes in the base of large flower pots... somehow it happened again, and they fixed it again, but he also told me you can buy a replacement chuck... so, so long as it doesn't get stuck with a drill bit in it, I will try undoing the screw like this video says, and then maybe go try and buy a replacement... Good luck with yours! let me know if you managed to sole it, if you feel like it :)
The Makita model number HP1640 does not have a chuck screw. If you follow the instructions shown in the video it will come off. The problem with Hammer Drills, is that because of the constant hammering the chuck will be harder to remove from the spindle. Make sure that you have the selector in drill only mode and not in hammer mode
i need to change the chuck on my dewalt dw991 i dont want to replace it with the 3/8 it has now can i put a 1/2 chuck on it ? if not the way it is what must i do
Dewalt doesn't show the 1/2" Chuck as an option. Usually the 3/8" drills have lighter duty transmissions, spindles and motors in them and they aren't able to handle the stress of the larger bits. The link for the 3/8" Chuck is as follows: www.ereplacementparts.com/keyless-chuck-jacobs-p-64641.html
Keyless Chuck (Jacobs, 3/8 [330075-46] for Power Tool ... www.ereplacementparts.com Buy a Keyless Chuck (Jacobs, 3/8 [330075-46] for your Power Tool - This 3/8" capacity chuck mounts to the drill using a 1/2"-20 threaded spindle. The light-...
eReplacementParts.com i also have the dewalt dw990 DeWalt said that the housing/shell is the same only different is sticker on back with model number Lowe's speed Manufacturing info housing cover cracked and i know that is a 1/2 inch chuck on that model i just need to replace the clutch because i can grab the chuck why i hit the trigger
Dewalt has 4 variations of the DW990 and another with model number DW990Q type 4 all of which show the Transmission as being no longer available and they don't offer a replacement suggestion. Just a heads up regarding Dewalt tool model numbers.... Dewalt tools sometime have different variation for the same model number. This is true for your DW990. These show Type 1, Type 2 and so on. It is very common for the parts between the different types to not be interchangeable.
eReplacementParts.com i understand i took the motor off of my dw990 and put it on my dw 991 with new carbon brushes as well as put the trigger switch that my dw990 useing same fwd and reverse switch that came on the dw991 because the fwd & reverse of my dw990 dont fit the shell of the dw991 but it's a hundred percent Improvement in performance and I can get the clutch with the spindle that can handle a 1/2 chuck on ebay new old stuck I might do that next and it would be like8 having my dw990 the way it was in 2001 when I purchased it i do own a newer lithium 12 v max but love the rock solid rocket construction of the older dewalts and other brands now they feel so cheap so my motor is of my type 4 dw990 dewalt so its a xrp model its heavy duty motor the trigger switch is from dw990 so its heavy duty k got a new clutch coming to me for dw990 with the right coller that turns up to 23 before drill icon i just need a new transmission gearbox and am back in business not to say it dont work just fine with the clutch from dw991 and transmission from the same model I'm just going to use it for diy repair projects around my house for work i use my dw995
I cut the outer sleeve length wise on a angle so I wouldn't cut the plastic housing with a band saw. Peeled the sleeve off put a releif cut next to a jaw and knocked the jaw out with a hammer and screwdriver. Could be done with a sawzall all the metals that were cut were very soft.
The1fuzzydog If the bolt is so seized that the head gets heavily damaged (or already is so) there's really not a more merciful option for the chuck and the whole drill.
why would you beat with the side of a snap on dead blow hammer ,,, good grief ,,, and then use water pump pliers where vise grips would work so much easier ,,,, ah well , at least your cream shirt stayed clean.
Thank you for the well illustrated advice. For a normal electric drill, you have to use a spanner to immobilize the threaded shaft that holds the chuck before striking the L key.
I took my electric Makita outside with the hex key in place, held it to the ground and put it in reverse. It did unscrew the chuck when the hex hit the ground, when hammering didn't work.
@@elultimo102 Thank you for your advice Elultimo!!!
I was listening with headphones and that knocking at the very beginning (in only one earpiece) had me jumping in my seat like "how the hell is someone knocking at my WINDOW? On the first floor???"
Don't do that!
Ahaha its 1:15am here and i just went to my door shook af because of it lmao
@@leviblank1886 same!
I enjoyed watching and learning how to get the Makita drill chuck unstuck. It was very direct and easy to follow. Thank you!
tried all you recommended but to no avail ,I had to cut off most of the old chuck with a hacksaw and then heat up the remains with a blowlamp (gas torch? USA ) only then did it come off . I must say I was very near throwing the thing in the trash (rubbish ) UK . took 2 hours.. and broke 3 impact driver bits trying to remove that centre screw .. even when I drilled out the screw the chuck would not give up and move.. thank goodness for heat .. I felt like had won the lottery when the chuck finally came off.. Conan, UK
I had to do the same but I used an angle grinder and cutting disc
Retaining screw is left-hand thread. GOOD TO KNOW!
I grinded a bolt down to 3 sides. Locked it in the chuck, put a socket on my impact driver. Much easier then hitting it with a hammer. IMO
you have a picture of a drill with it closed in the thumbnail, mine is closed... and its stuck. how do you get it off if its closed all the way?
Hit the beak with a hammer while trying to turn the chuck body to the open position.
How about if the problem is that the jaws won’t tighten so I can’t get an Allen key locked in there to hammer on?
I would love to see how someone would remove a stripped chuck on this 20v Porter cable drill I have the internal gears are stripped so it just slips even with air gun on it and yes the screw has been removed
A perfect video. Thanks. I just wonder who gave a "dislike" to this video?
me
@@tomthompson7400 why?
@@elmerovero7528
Start with the heres how to drill through your hand bit
work next on the hitting with the side part of a dead blow hammer
end with the if only i had some vise grips part
is that enough or do you need more ?
The fright at the beginning of the video made me pee myself just a little thinking someone was in the house knocking on the drywall.
Haha yeah fucking hell, could have sworn it was real
I’ve removed the retaining screw, but can’t get the Allen key to undo the Chuck, it’s just turning the motor of the drill.
Drill clamped to bench, low gear, drilling mode, 10mm Allen key and hitting anti clockwise.
Any ideas?
i have a Makita XPH07 and i got the screw out, but the chuck does not want to screw off. I;ve got it in the drill setting on no.1 as another video suggested. It is turning, but not coming off.
I have an old Ryobi D45C which uses a two part chuck with a thin nut at the bottom of the chuck. No retaining screw. The jaws are seized. How does one remove an old chuck like this?
What do I do when my drill chuck is seized in the smallest size (1/16") not (1/2") like in these videos?
Squirt a bit of WD-40 or any other kind of lubricant on the chuck and let is set for a minute. You can put some vise
grips on the chuck and try to bust it loose with a hammer.
Im trying to upgrade the chuck on a brand new drill and the retaining screw itself is not the problem. The chuck is screwed on so tight, I assume there is loctite involved. I could not get it to move no matter how hard I hit the allen key and I even damaged the chuck in the process. Can I take apart the gearbox from the inside to get the shaft out?
also if my chuck is stuck how will I tighten it down on an alan wrench?
Excellent video. My keyless chuck had jammed - shut of course - so I had to grind it off, but the video showed just where to grind, and the bit about the wrong-handed screw was essential, as was the advice on cooling and heating. Both were needed, so maybe you did it right. Tip: if your drill is a DeWalt, it has a Torx 20 screw. If you try to undo it fresh out of the freezer, the Torx bit shatters...
How come when i whack the allen key the drill wants to spin and wont get the chuck loose ? Am I missing something here. The drill is on low speed (1) and when i turn the allen key by hand first it stays really tight until i whack it with the hammer and the drill slowly spins. Is this just a really stubborn chuck or any other suggestions ?
It is a newer Makita brushless hammer drill.
Make sure the clutch is set to the Drill setting. That locks the chuck and drill together, so if one spins they both do.
Ok, I'm going to ask the obvious question - if my drill is the problem.... how can I drill it?
Mmmm, with another drill.
@@fabianore80 Are you going to run over with one for me? Because people aren't often in possession of more than one drill.
@@RiffRaffMama. Sure, will be my pleasure, where do you live, if you are far to from me, I have a solution for, you can take your drill, go to neighbor ask for share his drill for 2 minutes and do the job in his home, then give back it and say thanks. I am sure nobody will reject to share for a few minutes.
@@fabianore80 Dude, you've no idea where I live. My closest neighbour is kilometers away!
@@RiffRaffMama. By this reason I have two drills, one cordless for easy and fast jobs, and other corded to do rough tasks (stone, concrete). You should to consider to buy another drill too.
My driver drill's chuck has misaligned jaw (2 stucked at lower part, 1 at middle part). This method still unable to fix my drill issue. Do i need to replace the entire chuck?
Putting this here just in case it helps someone. I was watching this because I thought my chuck was damage, motor was spinning but chuck did not move. Turns out my drill was somehow stuck between 1 and 2 speed, making sure it was fully switch to one of the speeds fixed it.
Good thing too because I couldn't for the life of me get the chuck to come off with the hammer and alan key!
Omg thank you! I feel silly now
WHy do none of them state in what mode the drill needs to be, is i guess it needs to in remove or counter clockwise, right?
My harbor freight battery drill jammed. I saw the little screw and couldn't undo it so I did as suggested - tapped it with a long nail. The screw vanished and the chuck started working again.
my 3/8 completely seized and i had a half inch that fit the anvil threads. so far so good...the 1/2 inch seized too after i lube it. gee wiz
hello the problem is my device has 2 chuck its black & decker cordless 14.4v driver/drill i have screwed out the screw so easily but the problem with the 2 collars after turn one it goes to point that stop and start turning the one behind it so i tried to use 2 wrench one fix one and another wrench to loose the another collar but here is the big problem it doesnt loose whatever i push it so how to replace this doomed chuck i am stuck now with broken jaw teeth??!!
My makita teeth wont close, they are locked all the way open so bits just wobble inside. the chuck it'self wont turn much, just barely moves one way or the other and makes a snaping/locking in place sound when I turn it clockwise. sound like it should make that sound. luck the chuck is slotting into something. sorry i'm not a tool buff not sure how to explain it better. Do I still need to bust it open like this?
My defective chuck won't hold anything firmly....so using an allan key/hammer to remove it isn't gonna work.
I agree with the other comment the thumbnail shows a closed Chuck. that is my situation how do you fix that
There seems to be a million videos on removing a chuck, or fixing a chuck with a bit stuck in it. But I have twice accidentally opened a double-sleeve keyless chuck too far and it won't close again. Are there any videos on how to fix THAT?
Hi David, that's one problem that I haven't seen yet. I could not find any videos concerning it also.
I have a drill chuck with the reverse threaded screw removed. The CHUCK seems to be stuck and I cannot use a normal method to remove it. I think some one may have locktited the chuck but as it was newly purchased it may simply be caused by a seized thread. How can I remove the chuck? Good Video but doesnt apply to my problem.
What if your chuck wont tighten? I’d imagine the Allen wrench trick wouldn’t work in this case
How do you know when you’ve drilled out enough of the chuck screw?
Great video. Would this be the same method for a Hyper Tough brand as well? ? My drill has had the same problem for 2 days now.
Just found this channel to hopefully fix my Bosch drill. Awesome video and kick ass intro!
Is the replacement retaining screw just a screw or is it a particularly special screw that I need to obtain from the manufacturer?
You can pick up drill chuck retaining screws online.
Thank you so much! Finally I can get chuck of my drill (even it was a brand new Makita, nothing else helped).
Hi. Thank you. My 3/8 Stanley cordless drill chuck got stuck with a 6 mm bit in it. I didn't grip it too much, just normally, but it won't undo. It's stuck. Please share some ideas to free it up.
Thank you!
What do you do if you have a drill bit already in the stuck chuck?
See above
But I dont have a drill to drill my drill because my drill is broken...
I put a drill bit stuck in a vise and then I used the broken drill to drill itself
Can I buy a Jacobs keyless chuck for my drill motor ?? Where can I get that Sir ??? Thanks
Couldn't we just use a tool to remove the screw? I want to fix my drill not break it worse. Thanks.
You're right, watch this video instead th-cam.com/video/maZH2DRwd7Y/w-d-xo.html
Does any one perhaps know why a chuck starts to rattle and slip when i try to loosen it. It sounds like grinded teeth. It still drills and drives. Yet manually loosening the chuck sometimes makes this rattling sound
Thanks, was about to give up but worked 1st time thanks
Why the door knocking effect?
So what if you cant anything in the chuck because it actually is stuck
Ok, what if you a drill bit stuck in there you can't get out????
Thanks so much this video has really helped with my drill repair
What about a Makita right angle drill that has a huge Implement stuck in it and you can't open the Chuck even with wrenches
Time for the hammer, LOL! When this happens I've had good luck using a hammer and a punch. Clamp the stuck bit in a vise with the bottom of the drill chuck facing up. Place the punch on the chuck's body next to the jaws. Strike the punch with the hammer until the chuck's jaws slide off of the bit. This method will usually work. In the rare case that it doesn't, I will resort to cutting the chuck off of the drill with a grinder and cutoff wheel. -Mark
Thanks your advice was very helpful for me I have nearly given up on my drill. Thanks Again
hi i want to change DCD996 chuck but i am not sure how to do it. thanks
Mine has a bit stuck in the chuck?
What if you get the screw out but the chuck won't come off?
Ok, that knocking sound effect creeped me the eff out. With headphones it sounded like someone was knocking on the door. Too real dude.
It sounds to me like someone was knocking on the wall so I checked three times because I restarted watching this video three times.
Hi, My problem is with a Porter Cable cordless PCC600 with a broken Chuck stock about 5/16" open, but will not close or open running the motor back and forth, it's broken gears and Im unable to remove the inside T20 screw any ideas how to replace this broken chuck?, Cause the motor runs fine, it's a great drill and I will really like to keep it.
Please let me know.
Thank you! we
Thanks for the question. Here's a video for replacing the chuck: th-cam.com/video/bp_mXt3Zo5w/w-d-xo.html. We hope this helps!
What if it's welded on?
Hi, can you teardown Ryobi CDL1202P? I can't repair Ryobi 1202P gearbox, thanks :)
thank you - it worked for me very quickly!
How to open a chuck and clean it
hello i need help, i have a Makita XPH07 and i want to know whether i can change the chuck from keyless to SNS.
thanks any help very well appreciated
I haven't found an SDS Chuck that is compatible for your tool.
It'sm all good but my Jacobs chuck is stuck? It will NOT allow me to open it to change bits. It just won't open.. Any tips?
cassiya100 same problem..did ya figure it out.?
yep.. I had to use a large grip pliers, same type as used by plumbers.. grip it tight and twist, it should do the trick.
@@cassiya100 I'll try that
I got the retaining screw off of my Makita XPH07 but I can't get the chuck off, no matter how much I hammer it as shown.
Same problem with my DDF480 stucked chuck. Have tou manage to solve your stucked chuck issue?
Nope. I gave up. Fortunately the drill still works.
Hello , I have a Makita LXPH03 cordless drill , the problem I have is that the chuck pulls out of the gearbox with shaft intact..Is there any way to fix it??
Thanks
Unfortunately the shaft is part of the 126448-9 Gear Assembly. Makita does not provide any parts for the Gear Assembly. You would have to replace the complete gear assembly.
thanks for your help..
My countersunk is stuck in the chuck, and the chuck is stuck, impossible to undo & release my countersunk, so I am unable to even get to the stage of checking the chuck screw inside....
Suze Dunmow Hey, we're you able to undo the chuck of your drill? Mine just got stuck. It's an Stanley 12v drill. Very good until now.
Any ideas?
no, I couldn't do it, but then my hands are a bit older & weaker nowadays... I took it to my local hardware shop, and the very helpful guy did it with one strong twist. It had got a bit clogged with some plastic from me drilling holes in the base of large flower pots... somehow it happened again, and they fixed it again, but he also told me you can buy a replacement chuck... so, so long as it doesn't get stuck with a drill bit in it, I will try undoing the screw like this video says, and then maybe go try and buy a replacement... Good luck with yours! let me know if you managed to sole it, if you feel like it :)
Does someone succeed to remove chuck on an XPH07 drill. One day I try and no way... Please nedd help !!!
Wow Nice tips! Keep up the good work and more power to your channel. Thank you 😊
Dear sir help me plz how to remove chuck from HP 1640 makita drill
The Makita model number HP1640 does not have a chuck screw. If you follow the instructions shown in the video it will come off. The problem with Hammer Drills, is that because of the constant hammering the chuck will be harder to remove from the spindle. Make sure that you have the selector in drill only mode and not in hammer mode
I dig this beat
You can always depend on you guys to come up with a solution
Makita ddf481???
This makes me happy
Worked for me. Easy as pie
Great video. It worked for me..
if the chucked worked enough to clamp onto the big Allen wrench i wouldn't have to replace it...
File down the wrench to fit into the chuck. Chucks cost more than allen wrenches.
i need to change the chuck on my dewalt dw991 i dont want to replace it with the 3/8 it has now can i put a 1/2 chuck on it ? if not the way it is what must i do
Dewalt doesn't show the 1/2" Chuck as an option. Usually the 3/8" drills have lighter duty transmissions, spindles and motors in them and they aren't able to handle the stress of the larger bits. The link for the 3/8" Chuck is as follows: www.ereplacementparts.com/keyless-chuck-jacobs-p-64641.html
Keyless
Chuck (Jacobs, 3/8 [330075-46] for Power Tool ...
www.ereplacementparts.com
Buy a Keyless Chuck
(Jacobs, 3/8 [330075-46] for your Power Tool - This 3/8" capacity chuck
mounts to the drill using a 1/2"-20 threaded spindle. The light-...
eReplacementParts.com i also have the dewalt dw990 DeWalt said that the housing/shell is the same only different is sticker on back with model number Lowe's speed Manufacturing info housing cover cracked and i know that is a 1/2 inch chuck on that model i just need to replace the clutch because i can grab the chuck why i hit the trigger
Dewalt has 4 variations of the DW990 and another with model number DW990Q type 4 all of which show the Transmission as being no longer available and they don't offer a replacement suggestion. Just a heads up regarding Dewalt tool model numbers.... Dewalt tools sometime have different variation for the same model number. This is true for your DW990. These show Type 1, Type 2 and so
on. It is very common for the parts between the different types to not be interchangeable.
eReplacementParts.com i understand i took the motor off of my dw990 and put it on my dw 991 with new carbon brushes as well as put the trigger switch that my dw990 useing same fwd and reverse switch that came on the dw991 because the fwd & reverse of my dw990 dont fit the shell of the dw991 but it's a hundred percent Improvement in performance and I can get the clutch with the spindle that can handle a 1/2 chuck on ebay new old stuck I might do that next and it would be like8 having my dw990 the way it was in 2001 when I purchased it i do own a newer lithium 12 v max but love the rock solid rocket construction of the older dewalts and other brands now they feel so cheap so my motor is of my type 4 dw990 dewalt so its a xrp model its heavy duty motor the trigger switch is from dw990 so its heavy duty k got a new clutch coming to me for dw990 with the right coller that turns up to 23 before drill icon i just need a new transmission gearbox and am back in business not to say it dont work just fine with the clutch from dw991 and transmission from the same model I'm just going to use it for diy repair projects around my house for work i use my dw995
Thanks man! I fixed mine thanks to this video :)
Thank you , liked and subscribed
Great Video.
How about if itis seized around the bit?
I am still researching this for you. Will have a response soon. Thanks
Fixed it by hitting the end of the chuck with a hammer. Yay!
I cut the outer sleeve length wise on a angle so I wouldn't cut the plastic housing with a band saw. Peeled the sleeve off put a releif cut next to a jaw and knocked the jaw out with a hammer and screwdriver. Could be done with a sawzall all the metals that were cut were very soft.
Good vidéo thinks
Thank you! Thought my drill was shot. Here I forgot last time I used it, it was raining, so the clutch rusted shut. Thanks!
very helpfull tnx
Dor shem-tov chinyoul.mastar
that knock boss
I thought someone was legit knocking on my door
Hey thanks man it worked
How to remove in DCD996 dewalt ?
Hello, unfortunately we don't have a chuck for a DCD996.
Do you know how?
My chuck is stuck fully opened heeelp!
Hello my ryobi chuk is stuck please help me
Hello Ed, some chucks take quite a few hits to remove them. Just make sure your drill is in the drill mode and is set to low speed.
Will give it a try thanks 4 answering my question will get back to you
Nice it did work
I wish mine wouldn't bloody remove
bro that knocking was way too realistic with headphones
So I need another drill to fix my drill lol
yes, no good though, when you have a drill bit stuck inside
See below
Nice vid
Most disagreements can be settled with a hammer! …lol
how to remove a left hand threaded screw: use your other drill
The1fuzzydog If the bolt is so seized that the head gets heavily damaged (or already is so) there's really not a more merciful option for the chuck and the whole drill.
I can't believe there was all this screwing/unscrewing by hand. Just pull the trigger! That's how I always adjust/tighten my chuck.
1:33 That's some drill porn right there
Niceeee
why would you beat with the side of a snap on dead blow hammer ,,, good grief ,,, and then use water pump pliers where vise grips would work so much easier ,,,, ah well , at least your cream shirt stayed clean.
The background music is aggressive and useless. Anyway, good job
Repairing gears Gear from the inside drill Gear hammer ridgid